1987 Mercury Colony Park Performance and Racing Products

Competition design uses a stud, washer & nut to secure the clamp rather than a bolt. The clamp itself is also chromed. Fits 1962-2001 Small Block Ford V8s, including both Windsor and Cleveland as well as Ford 385 series 429/460 big blocks including Boss models.

Product Features:

• Eliminates bolt in favor of stud mount design
• Chrome plated
• Ideal For Ignition Distributor

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Die cut silicone rubber gaskets conform to out-of-flat covers
• Great for on-again/off-again situations
• Not intended for use in emission controlled vehicles.

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

• Oil Filled For Better Cooling
• Optimized Low Resistance
• Silicon Magnetic Steel E-Core
• Higher Energy/Voltage Outputs
• Quicker Starts
• Improved Idle Quality
• Resists Shock And Vibration
• Resists Corrosion

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

• Excellent Weight Transfer
• Lets Front End Down Quickly
• Maximum Traction
• Makes Vehicle Safer
• Easier Control At End Of Track
• Better Overall Stability

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

• Rynite Injection Molded Caps And Retainers
• Designed w/Performance In Mind
• High Quality; Voltage Insulating Material
• Stainless Terminals

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Flexplt: Bb Ford 70-97 (164T)

Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:

• Graphite-Impregnated Facing
• Steel Expanded Metal Core
• Superior Tensile Strength
• Resists Cracking
• Withstands Intense Heat
• Resists Deteriorating
• Anti-Stick Properties
• Easy Removal For Disassembly

Replace your stock black engine pulleys with chrome plated steel pulleys from Mr. Gasket.

Product Features:

• Triple Groove
• Chrome Plated
• Diameter: 5.90″

Product Features:

• Prevents Air Inclusion
• Direct Replacement
• For OE Bleeders
• One Person Bleeds Safely
• Without The Mess
• No Chance Of Air Bubbles

RngPnn

The Edelbrock part #41603 Classic Series Valve Covers are designed for Ford 221-351W V8 1962-95 applications and have a Black finish. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. Made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:

• Small Block Ford 221-351W 62-95
• Tall
• Black Aluminum
• Set Of Two

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
• With steel core to provide ultimate excellent blowout resistance.
• Not intended for use in emission controlled vehicles.

Our advanced power system line has grown to include starters. Our new APS starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The APS starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The armature is balanced during assembly and is guided by two ball bearings for smooth engagement and thousands of starts. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

• Mount Can Be Clocked To Assist In Mounting
• Downsized design helps clearance issues w/oil pans and exhaust
• Ball bearing supported armature and pinion gear
• 3 Hp Motor Provides Power For High Compression Engines
• Gear reduction of 4.4:1 improves torque for great cranking

The Original Pro Stick shifter delivers rock-solid performance, mixed with clean design cues and compact size. This is why you see so many Pro Stick shifters at the race track. We start off with a heavy duty steel base with a hardened steel gate plate, a reverse lockout feature that only requires one hand to operate, and complies with NHRA/IHRA safety rules. Then add the billet aluminum shift handle with classic white shift knob, lightweight aluminum trigger and finish it off with a brushed aluminum cover with quick release pins, and you end up with one good looking bullet-proof race shifter. Optional Forward and Reverse shift pattern gate plates are available for most popular 2, 3 and 4-speed transmissions. This model Pro Stick comes out of the box ready for action for most popular 3-speed transmissions, includes a 5-foot Super Duty shift cable, brackets, levers, hardware and detailed instructions for an easy installation. Be sure to check out all the optional Magnum Grip side grip plates including the one and two button 12-volt momentary switches or any of the other accessories we offer for the Pro Stick in the Shifter Accessories section. Notes: AOD requires installation kit #40496, AODE & 4R70W requires installation kit #40504, E40D & 4R100 requires installation kit #40505, 2004R & 700R4 require gate plate #80712, 4L60E – 4L85E equipped with PRNDL switch requires cable bracket kit #70499 and gate plate #80712. Overall Dimensions – 8.25L x 2.92W x 9.25H

Product Features:

• All One-Handed
• Reverse Lockout Meets NHRA And IHRA Requirements
• Mount Directly To Floor/Chassis/Or w/Quick Release
• Ultimate For Powerglide Applications
• Lightweight Brushed Alum. Cover
• Cover Removed Quickly and Easily
• Includes 5 Ft. Super Duty Race Cable
• Quick Change Plate Design

Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:

• Service Part
• No Moving Parts To Wear Out
• Self Contained Unit
• Can Drive OEM
• Can Drive High Performance Ignition Coils

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

• Ideal For Tight Spaces
• Serrations Prevent Loosening
• Flange Distributes Pressure
• Zinc Plated Bolts
• Grade 5 Material
• Easy Installation

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

• Manufactured from high-density cork/rubber blend gasket material
• Provides excellent sealing and durability
• For OE replacement, high performance street, drag race and oval track use

Product Features:

• Use W/ Valve Springs Part #5822, 5882, 5896, 5872, 5867, 5812, 5857
• Set of 16
• 1.50 in. Outside Diameter
• Steel Material
• Black Oxide Finish

MSD Ignition control are easy to install, but we also offer several plug-in harnesses. These are especially handy for quick installation on late model vehicles! The harnesses plug directly into your factory coil and harness then four color coded wires plug into the corresponding wires of the MSD. Two wires go from the MSD to the battery and you’re done with no cutting or splicing!

Product Features:

• Splice free installation
• Plugs directly into factory coil

Product Features:

• Designed for 1500 to 7000 Performance
• Large Plenum
• Long Tapered Runners
• 90mm. Throttle Body Opening
• Polished Finish

Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering

Product Features:

• Good blend of efficiency and performance.
• Perfect choice for performance street rebuilds.
• Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.

Product Features:

• Solid Bushing Chain Resists Stretching
• For Use with Stock or Edelbrock Camshafts
• Stressproof Steel Crank Gears
• 3 Keyway Setting Points To Ensure Accurate Timing
• True Bearing Surface Rolls with the Sprockets
• For Engine with One-Piece Fuel Pump Eccentric

Spectre’s Ford water neck fits Ford 390, 427 and 428 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

• Fits Ford 390, 427 and 428 engines
• Includes bolts and gasket
• Chrome plated
• Easy to install

MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase

Product Features:

• Rotor phasing can be adjusted.
• Ideal When Atomic TBI Is Controlling The Timing

The Edelbrock #38183 is a single-bore 90mm throttle body designed with a 5.0L Ford-style base pad. It is fully machined and assembled by Edelbrock. It includes a Throttle Position Sensor, a progressive throttle cable lever, and cruise and kick-down attach

Available in different sizes for many different vehicle models/years. Clean positive seal. Embossed silicone bead surrounding the port. Matched to manifolds and cylinder heads. In the early days of the automotive performance industry, you either ran what

Product Features:

• Clean positive seal
• Embossed Silicone Bead Surrounding The Port
• Matched To Manifolds And Cylinder Heads
• Fits 1963-96 289/302/351W Engines
• 10-Pack Of Gaskets

Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:

• Maximum Cooling for Street and Racing Engines
• Internal Passages Are Balanced for Maximum Flow
• Impeller is Larger than Others For Max Pressure
• Impeller Vanes Dramatically Increase Flow Rates
• Equal Distribution to Both Sides of Block
• Only Flows in One-Direction for Optimum Efficiency