from

$724.99

The off-road truck avenger is designed specifically for off-road applications. The unique fuel metering block eliminates fuel spillover through the boosters at extreme angles allowing for 40 degree climbing, 30 degree side hill maneuvers and nose-down descents to avoid hesitations, stalling and flooding typically associated with carbs in an off road environment. The 470 CFM off-road truck avenger is the perfect carburetor for 4 cylinder, V-6, and inline 6 cylinder engines. Viton(R) is a registered trademark of DuPont Performance Elastomers.

Product Features:

Gold Dichromate Finish For Extreme Off Road Environments
Single Feed Fuel Inlet For Ease Of Installation
Optimized Off-Road Calibration That Works Out-Of-The-Box
Factory Preset Electric Choke For Easy Startups
Quick Change Vacuum Housing Cap To Tune For Performance/Fuel Econ
One Piece Off-Road Vent Tube Eliminates Fuel Spillover
Metering Block For Flood Free Op. 40 deg. Climb/30 deg. Side Hill
Limited Lifetime Warranty Defects In Material/Workmanship

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$21.99

Mr. Gasket Performance Timing Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-density cork/rubber blend gasket material
Provides excellent sealing and durability
For OE replacement, high performance street, drag race and oval track use

from

$99.99

Product Features:

Use W/ Valve Springs Part #5703, 5794
Set of 16
1.50 in. Outside Diameter
Steel Material
Black Oxide Finish

from

$165.99

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

High Output Fuel Flow
Flows 130 gph Free Flow
Shutoff Pressure Pre-Set From 7.5 To 9 PSI
Fuel Pressure Regulator Required Recommend P/N 12-704
Heavy Duty Construction For Continuous High rpm Operation
Redesigned High Flow Valves Ensure Adequate Fuel Delivery
Fuel Body Casting Can Be Rotated For Plumbing Situations
Inlet And Outlet Tapped For 3/8 in. NPT

from

$85.09

Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:

Black Oxide Coated Grade 8 Steel
Kit Contains 16 Studs
Easy To Install
Heat Treated Steel
Prevents Stud Flexing
Black Plated Finish

from

$174.99

The B&M Transpak has all the features in the Shift Improver Kit, plus it provides additional driver manual control. Retain full automatic features and standard shift points with selector in Drive.

Product Features:

Recalibrate Auto. Transmission
Optimum Performance
Select Your App. Mode
Improves Transmission Life
Trans. Removal Not Required
Downshift At Any Speed
Great For Trailer Towing
For Heavy Loads Driving Downhill

from

$48.09

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

Indicates coolant temperature
Helps prevent coolant injuries
Fahrenheit and centigrade readings
Color-coded temperature ranges
Integrated coolant reclamation valve
Improves under-hood appearance
Chromed crown with a colored trim ring

from

$369.99

HoleShot 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) Application: HoleShot 2000 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot c

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$14.99

Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:

4 bolts included in each package
Allen head includes decorative O-ring cap
Triple chrome-plated finish
Fits standard height Chevy Center bolt valve covers

from

$394.99

Product Features:

High Rise/Dual Plane Design For Maximum Torque
Fully CNC Machined For A Perfect Fit
Square Bore Carburetor Flange
Exhaust Crossover For Improved Street Drivability
Permanent Mold Casting Process
Lighter/Smoother/Better Looking
More Consistent Castings

from

$443.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

7 in. Diameter
Absolutely the most accurate way to trigger the ignition.
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$342.99

Product Features:

Incredible Improvement in Control
Maintains Proper Caster and Camber Alignment
Increase in Handling and Control
Greatly Reduce Wheel Hop on Quick Acceleration
Even Braking Control is Improved
Better Suspension Stability

from

$499.99

Power Train

from

$23.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$31.99

ACCEL high performance standard size caps offer superior protection from arc-thru and crossfire. Features hi-performance. 60kV- rated alkyd compound, stress-relieved at molding to ensure stability. Brass inserts provide for high spark energy flow.

Product Features:

Brass Inserts Provide For High Spark Energy Flow

from

$38.99

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

Gains Both Performance and Longevity
Will Handle Any and All Torque
Out Lasts Rubber

from

$141.99

COMP Cams Hi-Tech Roller Race Timing Sets include cast iron camshafts gears, induction hardened billet steel crank sprockets, and pre-stretched, heat-treated double roller chains with heavy-duty large pin design. They feature 3 keyway crank sprockets for

Product Features:

Cast iron camshaft gear and induction hardened billet steel crank sprocket
Pre-stretched, heat-treated true double roller chain with heavy-duty large pin design; chain available separately
Ideal for all street performance and race applications
Features 3 keyway crank sprocket for 4-degree incremental adjustability, 4-degree maximum advance/retard
Dynamically balanced and quality checked for run-out tolerances

from

$296.99

Designed to fit Hooker Competition header, Manifold or catalytic converter back applications. Cat-back kits install behind the converter and all other applicable emission control devices.

Product Features:

Reducer Flex-Tubes
Reduces Backpressure
Hardware Included
Instructions Included

from

$27.49

Secure the harmonic balancer or dampener on your Chevy. Works on original equipment, high performance street, drag or circle track applications. Features a heat treated black oxide coated Grade 8 alloy steel bolt for strength with a tall hex head to prevent wrench from slipping. An extra thick parallel ground washer provides accurate, uniform torque, and a lock washer is also included.

Product Features:

Heat treated black oxide coated Grade 8 alloy steel
Tall hex head bolt to prevent wrench from slipping
Extra thick parallel ground washer provides accurate, uniform torque
Washers Provides More Accurate And Uniform Torque
Grade 8 Alloy Steel

from

$30.99

This Spectre Alternator Bracket is an upper mount designed to fit 1969 and later Chevrolet Big Block engines with a long water pump. Featuring a triple chrome-plated finish and high quality steel construction, this part is an OEM replacement that mounts on the passenger’s side.

Product Features:

Fits Big Block Chevy engines with a long water pump from 1969 and later
Manufactured from high quality steel
Upper bracket for passenger side mounting
Features a triple chrome-plated finish
Stock replacement part

from

$63.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
Not intended for use in emission controlled vehicles.

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$149.99

K&N performance High-Flow Air Filters are engineered to improve engine performance. Unlike disposable paper filters which must be frequently replaced, K&N Air Filters are washable, reusable, and engineered to last for the life of your vehicle or outdoor power small engine. Engineered to fit easily into your factory air box, installation can be completed in a matter of minutes! K&N develops and tests each product on the world┐s toughest race tracks, so we can bring the highest level of performance to your daily driving. Join the millions of customers who have saved money and improved vehicle performance by upgrading to K&N filtration.

Product Features:

ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (based on the average miles driven per year of 15,000 miles)
ULTIMATE LONGEVITY: No-hassle lifetime warranty on stock replacement K&N air filters- limitations apply
EASY INSTALLATION: K&N Air Filters are pre-treated and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
ECO-FRIENDLY: Using a washable, reusable engine air filter helps reduce replacement air filter waste- a K&N air filter is designed to last longer than 10 or more disposable filters
MADE IN USA: K&N Air Filters are proudly made in the USA for trusted quality & reliability

from

$148.99

Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.

Product Features:

Thicker Than Stock Steel Plate
Ring Gear Securely Welded
Dual Bolt Patterns
Zinc-Dichromate Plated To Resist Corrosion
Withstands High Torque and RPM

from

$31.99

Mr. Gasket Ultra-Seal Intake Manifold Gasketss are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For original equipment replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use

from

$10.49

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features: