from

$309.99

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit is used in 8.5″ differentials using a Yukon Dura Grip, Eaton posi, ValueTrac, True Trac, Pro-Series Auburn, Detroit Locker or standard carrier with large bearing journals. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. Includes Supershims.

Product Features:

Fits GM 8.5″ rear with aftermarket positraction
Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

from

$4.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$57.99

Product Features:

Crush sleeve eliminator kit for GM 8.5″, 8.6″ and Chrysler 9.25″ rear

from

$109.99

12P, 12T, CI VET, & 55GM 8460N REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits GM 12 bolt passenger car, 12 bolt truck and 1963-1979 Corvette

from

$6.59

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$39.99

8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.

Product Features:

Pinion depth shim kit for Toyota 7.5″, 8″ and V6

from

$28.99

Positraction cross pin bolt for GM 12P and 12T.

Product Features:

Cross pin bolt for GM 12 bolt passenger car and truck
For OEM positraction applications only

from

$209.99

Product Features:

Spider gear kit
Fits GM 8.5″ 28 spline open differential
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$226.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits GM 8.5″ front
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

from

$9.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$83.99

Replacement front axle inner seal redi-sleeve for Dana 44 & 8.5″ GM.Yukon Mighty seal.

Product Features:

Axle Redi-sleeve
Fits Dana Spicer 44

from

$232.99

8.5″ GM EXTRA HD standard Open case (uses larger bearings).

Product Features:

Standard open carrier case
Fits GM 8.5″ with 28 or 30 spline axles
2.73 and up ratio only
Does not include spider gears
Has larger carrier carrier bearing journals for high strength

from

$139.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$188.99

Mini spools are a low-cost traction option for vehicles looking for full-time lockup. The mini spool installs into a standard open carrier and give 100% power to both tires at all times. These units are not recommended for street-driven vehicles. We recommend full spools for vehicles with large tires or high horsepower. These units come with a one year warranty against manufacturing defects.

Product Features:

Fits GM 8.5″ with 30 spline axles
Installs into a standard open carrier case
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$404.99

Product Features:

Clutch kit
Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction
14 piece kit
Carbon fiber clutches

from

$11.99

8.5 front cover gasket.

Product Features:

Cover gasket
Fits GM 8.5″ front

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$7.79

Product Features:

Brand may vary by location

from

$4.99

3/8″ ring gear bolt washer for GM 12 bolt car & truck, 8.2 BOP & more.

Product Features:

Ring gear bolt washer for GM 12 bolt car and truck, 1955-1964 passenger car, 1963-1979 Corvette and 8.2″ Buick, Oldsmobile and Pontiac

from

$148.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for GM 8.5″ differential with HD bearings for large journal carrier. This kit contains carrier bearings, races and shims. This kit is used in 8.5″ differentials using a Yukon Dura Grip, Eaton posi, ValueTrac, True Trac, Pro-Series Auburn, Detroit Locker or standard carrier with large bearing journals.

Product Features:

Fits GM 8.5″ with aftermarket positraction
Works with Heavy Duty Bearings
Includes carrier bearings and races and “super” carrier shim kit

from

$425.99

Yukon positraction internals (0.806″ diameter) for GM 12P and 12T with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit GM 12 bolt passenger car and truck Dura Grip positraction with 30 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$9.99

Pinion nut for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.0″, 8.25″, 8.5″, 8.6″, 9.25″ IFS, 9.5″ & Oldsmobile Dropouts. 1 1/4″ socket, 7/8″ x 14 thread.

Product Features:

Pinion nut for GM 7.2″, 7.5″, 7.625″, 8.0″, 8.25″ IFS, 8.5″, 8.6″, 9.25″ IFS and 9.5″
7/8″ x 14 thread
1 1/4″ socket

from

$259.99

The Motive Gear replacement axle shaft offers an OE-quality axle shaft at a fraction of the OE cost. Manufactured from 1541H material on high-tolerance CNC equipment, this axle shaft is designed to provide a perfect fit every time.

Product Features: