1985 Chevrolet K30 Performance and Racing Products

Essential 1985 Chevrolet K30 Performance and Racing Products

Edelbrock – Performer Small-Block Chevy Cylinder Head 64cc Hydraulic Flat Tappet (Part No.60909)

Performer Small-Block Chevy Cylinder Head 64cc Hydraulic Flat Tappet

from

$1009.99
Product Features:
  • 50-State Street Legal Aluminum Cylinder Head
  • Out-of-the-Box Bolt-On Performance
  • 64cc Combustion Chambers Improve Performance
  • Retain Stock Compression Ratio
See More

MSD Ignition – Wire Set; Black Super Conductor; Small Block Chevy with HEI Cap (Part No.35593)

Wire Set; Black Super Conductor; Small Block Chevy with HEI Cap

from

$109.99
The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:
  • Less than 50 ohms per foot for superior spark
  • Ferro-magnetic impregnated core creates an effective EMI choke
  • 40 ft. Of Conductor Wound Into A Single Foot Of Wire
  • For high EMI suppression
  • Conductor core features Dupont Kevlar material
  • Proprietary compound sleeves for resistance to high heat/abrasion
See More

MSD Ignition – Rotor; Extreme Output; GM HEI (Part No.84101)

Rotor; Extreme Output; GM HEI

from

$30.19
With the introduction of our 20 Amp extreme HEI module, we needed an HEI cap and rotor that could withstand the high output. The answer was to mold our own HEI cap, rotor and coil cover. The cap and rotor will fit our HEI Pro-Billet distributor, PN 8365, plus will work on stock applications.

Product Features:
  • Extreme output rotor
See More

MSD Ignition – Distributor; Crank Trigger; Chevy V8 Low Profile (Part No.84697)

Distributor; Crank Trigger; Chevy V8 Low Profile

from

$384.99
The unique design of these distributors fit tight intake systems while still transferring the high voltage of the MSD racing ignition to the spark plugs. The high voltage carrying capabilities are the result of several features which have been designed to fit the tight quarters and still accurately deliver sparks.

Product Features:
  • Designed to fit low in the block to clear firewall/intake combos
  • Supplied w/Bronze Gear
  • Supplied w/Large Diameter HEI Style Distributor Cap And Rotor
  • Must Be Used w/An MSD Crank Trigger And MSD Ignition Control
  • O-ring seals can be installed for oil press. control (Mods only)
  • Special oil tract improves lubrication to the dist./cam gear
  • QPQ coated polished steel shaft; guided by sealed ball bearings
  • Oversized Polished Steel Shaft w/QPQ Coating
See More

Mr. Gasket – A/Tdipstick (Part No.9704G)

A/Tdipstick

from

$79.99
Billet aluminum handle with flexible braded steel tube mounts to the firewall. 29-3/4 inch long.

Product Features:
  • Braided Stainless Steel
  • Firewall Mounting
  • Includes Oil Fill Tube
See More

Hays – Power Train (Part No.10-132)

Power Train

from

$499.99
Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:
  • Certified Billet Material
  • Borg and Beck Clutch Pattern
  • Long-Style Clutch Pattern
  • Ring Gear Securely Mounted To Prevent Spinning
See More

PerTronix – D4061 Flame-Thrower HEI Distributor Rotor Red (Part No.D4061)

D4061 Flame-Thrower HEI Distributor Rotor Red

from

$15.99
Made from hi-performance 60 KV rated alkyd molding compound for superior protection from “arc-thru” and cross-fire. Our cap and rotor kits include nylon rotor hold-down screws. Flame-Thrower dust covers provide a larger air gap around the coil which provi

Product Features:
  • PerTronix D4061 Flame-Thrower HEI Distributor Rotor Red
  • Made from hi-performance 60 KV rated alkyd molding compound.
See More

Mr. Gasket – Timing Tab (Part No.4598)

Timing Tab

from

$15.99
Bolts on with existing timing cover bolts. It is chrome plated steel, which makes is a better compliment to a chrome timing cover. It also has an adjustable red timing pointer. This allows for better visibility and helps you set your timing more easily. Just loosen the screw, set the pointer to the desired initial timing level, and screw it back down. Then you’ll be able to more clearly see if your timing is where you want it when checking your timing.

Product Features:
  • Bolts on using existing timing cover bolts
  • Chrome finish compliments chrome timing covers
  • Red adjustable pointer makes it easier to check timing
See More

Mr. Gasket – Enhancement Products (Part No.2060)

Enhancement Products

from

$10.49
This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:
  • Internally battled
  • High-porosity filter
  • Ideal for high performance
  • Includes rubber grommet
See More

Hooker Headers – Competition Header (Part No.2463HKR)

Competition Header

from

$410.99
LS1 full length engine swap header fits 66-72 Chevelle, El Camino, Monte Carlo and Sprint applications. Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • High Performance
  • Affordable
  • Durable 16 Gauge Material
  • Welds Easier
  • Lasts Longer
  • Heat Cured
  • High Heat Resistant
See More

MSD Ignition – Crank Trigger Kit; Small Block Chevy; 6? Balancer (Part No.8600)

Crank Trigger Kit; Small Block Chevy; 6? Balancer

from

$461.99
For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:
  • 6.25 in. Diameter
  • Absolutely the most accurate way to trigger the ignition.
  • The non-magnetic pickup cannot be false triggered.
  • Powerful magnets are embedded in a billet aluminum trigger wheel.
See More

Spectre – Spectre Replacement Air Filter (Part No.HPR0136)

Spectre Replacement Air Filter

from

$31.99
This Spectre OEM replacement air filter is an easy to install performance option for multiple Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac applications that use a 14 inch by 3 inch round air filter. With its performance synthetic air filter media, this air filter has been designed to add horsepower and quicker acceleration by allowing more air flow into your engine than ordinary paper filters. This air filter’s sealing edge was engineered to insure a proper air cleaner housing seal for great engine protection.

Product Features:
  • Replacement for 14 inch by 3 inch round air filter
  • Fits perfectly in your vehicle’s air box as a replacement for your factory air filter
  • Engineered for increased flow and greater performance
  • Fits select Buick, Cadillac, Chevy, GM, Mercedes, Oldsmobile and Pontiac models
  • Factory pre-oiled and ready to use
  • Simple installation
See More

Spectre – Valve Cover (Part No.5220)

Valve Cover

from

$57.99
Available in various sizes, heights, and finishes, Spectre offers a wide variety of high performance valve covers designed to easily replace your stock covers. Designed for 1958-1986 Chevrolet Small Block 265-400 engines, this valve cover features chrome-plated steel construction and a smooth design. Sold in pairs, this stock profile cover is baffled to provide optimum function. With show quality construction and a sealing edge designed for an ideal fit, our valve covers are engineered to look great for applications ranging from custom builds to replacing stock equipment.

Product Features:
  • Designed for 1958-1986 Chevrolet Small Block 265-400 engines
  • Baffled for breather system compatibility
  • Sold in pairs
  • Triple chrome-plated steel construction
  • Stock height
  • Features OEM style sealing edge
See More

Mr. Gasket – Valve Cover Gasket Set (Part No.179)

Valve Cover Gasket Set

from

$36.99
Mr. Gasket Performance Valve Cover Gaskets are high-density cork/rubber blend gaskets that use evenly sized cork particles distributed evenly throughout the rubber binder. The result is a compressible valve cover gasket without leak paths. These gaskets create a positive seal by controlled swelling of the gasket material when exposed to hot engine oil. Provides excellent flange sealing and durability. For original equipment replacement, high performance street, drag race and oval track use.brbrThese gaskets are .312 inch thick. That’s substantially thicker than stock which can allow for additional valve train clearance. brbrFits Chevrolet 262,265,267,283,307,327,350,400 Gen I Small Block with Perimeter Bolt Valve Covers.

Product Features:
  • Provides Excellent Flange Sealing And Durability
  • For High-Performance Street, Drag Race & Oval Track Use
See More

B & M – Shift Improver Kit, 82-93 TH700R4 (Part No.70239)

Shift Improver Kit, 82-93 TH700R4

from

$73.99
The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:
  • Provides Crisp Shifts
  • On Any Stock Automatic Transmission
  • Eliminates Soft/Sluggish Shift
  • Eliminates Shift Overlap
  • Eliminate Clutch and Band Wear
  • Improves Transmission Life
  • Transmission Removal Not Required
See More

Mr. Gasket – Intake Manifold Bolts (Part No.6091)

Intake Manifold Bolts

from

$32.09
These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:
  • Features 12-point Smaller-than-standard Bolt Head
  • Thick Flat Washers Distribute Optimum Clamp Load
  • Ideal Use Where Space Is Minimal On Race Manifolds
  • Bolts And Washers Zinc Plated For Protection
  • Zinc Plated For Protection
See More

Edelbrock – Water Pump Big-Block Chevy Standard/Long in Polished Finish (Part No.8861)

Water Pump Big-Block Chevy Standard/Long in Polished Finish

from

$475.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Hays – Power Train (Part No.85-114)

Power Train

from

$653.99
High burst strength woven lining to withstand heat and higher engine RPM. Heavy-duty sprung hub assembly to allow smooth engagement and steady torque transfer without chatter. Recommended for high horsepower street vehicles in addition to occasional drag strip use.

Product Features:
  • Built As Matched Assembly
  • Exceptional Performance
  • Exceptional Durability
  • Long Term Dependability
See More

Edelbrock – Cylinder Head Gasket Set for Chevrolet (Part No.7310)

Cylinder Head Gasket Set for Chevrolet

from

$58.99
Product Features:
  • 4.125 in. Cylinder Bore Diameter
  • 0.039 in. Thickness
  • 8.7cc Volume
  • Charcoal Color
  • Two Piece Configuration
See More

MSD Ignition – Distributor Cap and Rotor; MSD/GM V8 Points (Part No.8442)

Distributor Cap and Rotor; MSD/GM V8 Points

from

$49.49
The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:
  • Fits MSD/GM V8 Distributors
  • Made from high quality materials
  • Brass terminals
  • High dielectric properties
See More

Fram – High Performance Spin-on Oil Filter: Ideal for Racing Oil (Part No.HP4)

High Performance Spin-on Oil Filter: Ideal for Racing Oil

from

$16.99
FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.** 

Product Features:
  • Proven protection for up to 10,000 miles
  • Engineered for use with synthetic or conventional motor oils
  • Filter media is a blend of fiber and resin that captures 95% of the dirt particles
  • The perfect balance of dirt-trapping efficiency and dirt-holding capacity
See More

Dynomax – Dual Header Exhaust System Kit for Classic 4WD Trucks & SUVs (Part No.89003)

Dual Header Exhaust System Kit for Classic 4WD Trucks & SUVs

from

$209.99
Give your vintage vehicle’s exhaust system an upgrade with a DynoMax? dual header kit. Designed to attach to OE manifolds, it features a special reducer that allows for a variety of mounting options.

Product Features:
  • COMPATIBILITY — Designed for a variety of full-size 1973-89 GMC 4WD trucks and Chevrolet 4WD SUVs; see product information for compatibility and engine spec
  • BUILD IT YOURSELF — Design and custom fabricate your own exhaust system with this kit that attaches to OE manifolds
  • FLEXIBLE MOUNTING — Special reducer design allows for a variety of mounting options
  • IMPROVED FLOW CAPACITY — Smooth bends improve flow capacity over traditional bends
  • SPECS — Extra-long tailpipes with side exits with a full 2.25-in. diameter; tailpipes exit each side of vehicle behind rear tires
  • COMPLETE SOLUTION — Includes all the necessary clamps, hangers, flanges, gaskets, mounting hardware, intermediate, extension and tail pipes
  • PREMIUM MATERIALS — Made from quality aluminized steel for durability and long life
  • PREMIUM MATERIALSÿ–ÿMade from quality aluminized steel for durability and long life
  • BETTER TOGETHER — Complete your system with premium DynoMax mufflers and DynoMax accessories for a complete performance exhaust system
  • WARNING — Not legal for use on pollution-controlled motor vehicles
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Holley – Mechanical Fuel Pump (Part No.12-327-13)

Mechanical Fuel Pump

from

$165.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • High Output Fuel Flow
  • Flows 130 gph Free Flow
  • Shutoff Pressure Pre-Set From 7.5 To 9 PSI
  • Fuel Pressure Regulator Required Recommend P/N 12-704
  • Heavy Duty Construction For Continuous High rpm Operation
  • Redesigned High Flow Valves Ensure Adequate Fuel Delivery
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 3/8 in. NPT
See More

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

from

$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Energy Suspension – Motor and Transmission Mount (Part No.3.1130G)

Motor and Transmission Mount

from

$109.99
Product Features:
  • Re-Engineered to Handle High Horsepower
  • Outlasts Rubber
  • Virtually Indestructible
See More

FEL-PRO Performance – PERFORMANCE REAR MAIN SEAL SET (Part No.2904)

PERFORMANCE REAR MAIN SEAL SET

from

$16.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Meets or exceeds all original equipment specifications
  • Application specific design to ensure a perfect fit
  • Engineered and manufactured specifically for repair applications
  • Unsurpassed quality you can trust
  • Validated for fit, form, and function
See More

Competition Cams – FUEL PUMP PUSH ROD, CHEVY 1 EA (Part No.4607)

FUEL PUMP PUSH ROD, CHEVY 1 EA

from

$53.99
When a high pressure fuel pump is run with a steel roller cam core, the stock fuel pump pushrod is not compatible with the steel core. You can damage an expensive roller cam as a result of wear at the fuel pump lobe. COMP Cams offers several fuel pump pushrods for various applications.

Product Features:
  • Lightweight tubing with bronze tip for steel cams
  • 5.75″ Length
  • Eliminates wear at the fuel pump lobe often caused by a stock fuel pump pushrod
See More

Popular 1985 Chevrolet K30 Performance and Racing Products Categories

1985 Chevrolet K30 Performance and Racing Products

You count on your 1985 Chevrolet K30 to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Performance and Racing Products. With 290 Performance and Racing Products ranging in price from $7.99 to $1,009.99, you’re sure to find everything you need for your 1985 Chevrolet K30.

Brands matter. If you want to shop a specific Performance and Racing Products brand, we stock 22 different brands like Mr. Gasket, Edelbrock, and K&N. 1985 Chevrolet K30 Performance and Racing Products start as low as $7.99!

One of the best ways to find top quality OEM or aftermarket Performance and Racing Products is by asking professionals. Short of that, you can shop with confidence thanks to our 803 extensive product reviews on 1985 Chevrolet K30 Performance and Racing Products. Some of the top-rated Performance and Racing Products products we carry are Distributor; Street Fire; Chevrolet V8 GM HEI with 4-Pin Module with 4.7 stars and GM 1984-95 Remote Supercoil with 3.9 stars.

Did we mention you can order your Performance and Racing Products from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Performance and Racing Products inventory for your 1985 Chevrolet K30 below to get started!

Top-Rated Performance and Racing Products Brands For Your 1985 Chevrolet K30

Trusted Performance and Racing Products OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 1985 Chevrolet K30 running right for years to come. In our inventory you’ll find brands like Mr. Gasket, Edelbrock, K&N, and even more.

Popular Flowtech Performance and Racing Products

You’ll find popular Flowtech brand products across Performance Exhaust Products. All are waiting to get your 1985 Chevrolet K30 back on the road. Some of the top-rated Flowtech products in these categories are:
Real-Seal; Header Gasket
from $85.39
(1)
Real-Seal; Header Gasket
Performance Exhaust Manifold Gaskets

Top-Rated Edelbrock Performance and Racing Products


If Edelbrock are what you’re looking for, our inventory holds plenty. We stock Edelbrock brand Performance and Racing Products for your 1985 Chevrolet K30, and some of our most reviewed Edelbrock parts include:
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
from $195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds

FAQs for 1985 Chevrolet K30 Performance and Racing Products

What are the most purchased Performance and Racing Products for the 1985 Chevrolet K30?

Out of 290 Performance and Racing Products for the 1985 Chevrolet K30, the most popular in our inventory are:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats
Ultra-Seal Intake Manifold Gasket with Silicone Beading
from $31.99
(18)
Ultra-Seal Intake Manifold Gasket with Silicone Beading
Performance Engine Intake Manifold Gaskets

What are the top-rated 1985 Chevrolet K30 Performance and Racing Products?

Top-rated Performance and Racing Products for your 1985 Chevrolet K30 based on customer reviews/ratings are:
Distributor; Street Fire; Chevrolet V8 GM HEI with 4-Pin Module
from $259.99
(20)
Distributor; Street Fire; Chevrolet V8 GM HEI with 4-Pin Module
“Best Distributor I have ever bought, has made a big difference on my small block Chevy. Stronger spark, more powerful combination, which allows no mor”
GM 1984-95 Remote Supercoil
from $79.99
(15)
GM 1984-95 Remote Supercoil
“Works great!”
Performance Exhaust Gasket Set for Enhanced Sealing and Durability
from $20.99
(14)
Performance Exhaust Gasket Set for Enhanced Sealing and Durability
“Put new headers on motor”