1982 Ford F-100 Differentials

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses carrier bearings & races with an I.D. of 1.625″ and an O.D. of 2.891″. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

• Fits Ford 9″ with LM501310 carrier races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, pilot bearing, marking compound and brush.

Genuine Spicer light vehicle axle products are manufactured to the same high standards as original equipment (OE) parts because they are OE parts. That means when an automotive axle part is replaced with a genuine Spicer part, you are getting the same performance and reliability you have come to expect. And because Dana is constantly revolutionizing the technology behind its Dana axles and Spicer products, the replacement car axle or component you purchase today may even exceed the standards set for the original equipment part that you are replacing.

Product Features:

• Genuine OE quality. Tested and proven.
• Ultrasonically tested for internal cracks that magnetic testing can miss.
• Built from high grade steel that stands up to any grade on the market.
• Engineered for consistent quality and durability.

Product Features:

• Fits Chrysler Dana Spicer 60 with 35 spline axles
• 4.56 and up ratio only
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with Daytona pinion support
• Included are pinion bearings and races, pinion seal, crush sleeve eliminator , complete pinion shim kit, and marking compound with brush.

Product Features:

• Pinion depth shim kit
• Fits Ford 9″ with 7/16″ pinion support bolts

Yukon Power Lok positraction replacement internals for Dana 44 and Chysler 8.75″ with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 44 and Chrysler 8.75″ Powr Lok positraction
• Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

O-ring for 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion support o-ring
• Fits Ford 9″

Trac Loc clutch guide for 9″ Ford.

Product Features:

• Clutch guide
• Fits Ford 8″ and 9″

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Trac Loc uses a nodular case, billet side hat, and forged internals for higher strength than stock Trac-Locs. The units use composite clutches for high performance and long life. All units are Rebuildable. Yukon offers a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″ with 28 spline axles
• Trac Loc positraction
• Clutch style positraction
• Aggressive design
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

DiffrlPinSupport

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

• Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
• 1/2″ x 18 thread

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

9″ Ford gasket.

Product Features:

• Dropout gasket
• Fits Ford 9″

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

• Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

• Side adjuster
• Fits Ford 9″
• 3.062″ designs only

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

• Carrier race
• Fits Ford 9″
• Conversion race to install small bearing carrier into 3.250″ dropout

1310 and 1330 U/bolt kit (2 U-bolts and 4 nuts) for 9″ Ford.

Product Features:

• u-joint u-bolt kit
• Fits Ford 9″
• 1310 and 1330 u-joint size
• Includes two u-bolts and four nuts

Product Features:

• SOLID SPACER FORD 8.8″ & 9″

Product Features:

• NODULAR HOUSING 9″ FORD 3.25″ BORE

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; multi-lip
• Temperature range: -20 Deg. F to 300 Deg. F / -29 Deg. C to 49 Deg. C
• Resistance to EP lubricants
• Low swell in hydrocarbon fluids
• Delivers quality and reliable performance for every type of repair

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Ford 9″
• Works with Spartan Locker or standard open spider gears
• Long shaft

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

• Fits Dana Spicer 44 with 30 spline axles
• 3.92 and up ratio only
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Product Features:

• Carrier shim kit for Dana Spicer 30 and Dana Spicer 44 with 19 spline axles

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Bearing race driver for Dana 44 front (TK 02820). No return.

Product Features:

• Bearing race driver
• Fits 02820 race
• All steel construction