1977 Ford F-100 Differentials

Product Features:

• Nodular iron for added strength
• Thick design
• Durable powder coat finish
• Magnetic drain plug
• Made in USA
• High strength stainless steel fasteners

Differential

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses carrier bearings & races with an I.D. of 1.780″ and an O.D. of 3.062″. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Ford 9″ with LM603011 carrier races and Daytona pinion support
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, pilot bearing, thread locker, marking compound with brush, and gasket.

9″ Ford gasket.

Product Features:

• Dropout gasket
• Fits Ford 9″

Product Features:

• Cover gasket
• Fits Dana Spicer 60, 70, 70U and 70HD

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Dana Spicer 60 rear
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil baffles and slingers, thread locker, marking compound with brush and gasket.

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

• Power Lok case bolt for Dana Spicer 60 and 70
• 7/16 x 14 thread
• 3.5″ long
• 9/16″ hex head

Product Features:

• Oil baffle for Dana Spicer 44

Yukon Performance full spool for Dana 60 with 30 spline axles. fits 4.56 and up. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler Dana Spicer 60 with 30 spline axles
• 4.56 and up ratio only
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

• Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

Yukon replacement trail repair kit for Dana 30 and 44 with 1310 size U/joint and u-bolts. This kit comes with a yoke, U/joint, pinion seal, U/bolt or strap kit, pinion nut, and pinion nut washer (if applicable).

Product Features:

• Fits Dana Spicer 30 and 44
• 1310 u-joint size
• Kit includes yoke, U-joint, pinion seal, pinion nut and washer, U-bolts and threadlocker

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

• Carrier bearing puller
• Works with an impact gun to safely and easliy remove carrrier bearings
• Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

Ford 8″ & 9″ TracLoc ring gear bolt, 1-1/4″ long.

Product Features:

• Ring gear bolt for Ford 8″ and 9″
• For use with Trac Loc limited slip
• 1.25″ long

Axle shaft damaged or bearings worn out. This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Product Features:

• Driven plate
• Fits Dana Spicer 44 Powr Lok

Yukon standard open spider gear kit for 9″ Ford with 31 spline axles and 4-pinion design. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Ford 9″ open differential with 31 spline axles
• Includes two side gears, four pinion gears, cross pin shaft, roll pins and spider gear thrust washers.

Product Features:

• Fits Ford 9″ with 28 spline pinion
• Larger inner pinion bearing reduces gear deflection under high load
• Races installed
• 6061 aluminum
• Annodized purple

Product Features:

• SOLID SPACER FORD 8.8″ & 9″

Pilot bearing retainer for Ford 9″.

Product Features:

• Pilot bearing retainer for Ford 9″

Fine thread pinion support bolt (aftermarket aluminum only) for 9″ Ford.

Product Features:

• Pinion support bolt for Ford 9″
• 3/8″ x 24 thread
• 1.5″ long

Product Features:

• Inner oil slinger for Dana Spicer 60

Product Features:

• Pinion depth shim kit
• Fits Ford 9″ with 7/16″ pinion support bolts

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

One (1) specialty bearing race to adapt small bearing journal into a 3.250″ dropout. This adapter allows the use of a 28 or 31 spline carrier, positraction or locker in a 3.250″ dropout. This is a perfect solution if you are currently running 28 or 31 spline axles but are looking to upgrade to 35 spline later, or are stepping down from 35 spline but don’t want to buy a new dropout.

Product Features:

• Carrier race
• Fits Ford 9″
• Conversion race to install small bearing carrier into 3.250″ dropout

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9″ with35 spline pinion
• For oversize applications
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

• Side adjuster
• Fits Ford 9″
• 3.062″ designs only

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only