1982 Chevrolet Camaro Performance Engines

Essential 1982 Chevrolet Camaro Performance Engines

Edelbrock – Pushrod Set for S/B Chevy (Part No.9629)

Pushrod Set for S/B Chevy

from

$187.99


Product Features:
  • Case-Hardened Tubing
  • Surface Hardening
  • Welded Ends
  • 0.3125 in. Diameter
  • Use with or without Hardened Steel Guideplates
See More

Edelbrock – Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet (Part No.3702)

Performer-Plus Camshaft Kit for 1976-95 Small Block Chevrolet

from

$306.99


Product Features:
  • Designed for Optimum Torque and Acceleration
  • Maximum Performance From Idle through Mid-Range
  • Matched to Edelbrock Performer Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Major Improvement in Throttle Response and Torque
  • Use For Daily Drivers/Trucks/Vans/RVs/4x4s
  • Take The Guesswork Out Of Camshaft Selection
See More

Edelbrock – Performer Series Retainer (Qty 16) (Part No.9730)

Performer Series Retainer (Qty 16)

from

$99.99
Product Features:
  • Use W/ Valve Springs Part #5703, 5794
  • Set of 16
  • 1.50 in. Outside Diameter
  • Steel Material
  • Black Oxide Finish
See More

Mr. Gasket – Ultra Seal: Competition Screw-In Rocker Arm Studs (Part No.1074)

Ultra Seal: Competition Screw-In Rocker Arm Studs

from

$85.09
Mr. Gasket competition screw-in rocker arm studs are manufactured from heat treated black oxide coated Grade 8 steel. Ideal for high performance street and race applications.

Product Features:
  • Black Oxide Coated Grade 8 Steel
  • Kit Contains 16 Studs
  • Easy To Install
  • Heat Treated Steel
  • Prevents Stud Flexing
  • Black Plated Finish
See More

Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)

Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads

from

$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Mr. Gasket – Intake Bolt Kit (Part No.5003)

Intake Bolt Kit

from

$75.99
Finish your custom engine job with these show quality grade 5 chromed 12-point bolts, includes AN washers which have no exposed shoulder for a professional appearance. Includes (12) 3/8-16 x 1 inch bolts with (12) 3/8 inch AN washers.

Product Features:
  • Chrome plated
  • Grade 8
  • 12-point head
  • AN washers with no exposed shoulder for a professional appearance
See More

Mr. Gasket – Tstat (Part No.6368)

Tstat

from

$31.99
Designed to open at 180 degrees every time, regardless of engine rpm, and it’s high-flow design and brass and copper construction eliminate the damaging effects of cycling when you’re stuck in stop-and-go traffic. It includes the rubber gasket and has a pressure relief valve.

Product Features:
  • Opens sooner than stock at 180 degrees
  • High flow design for performance applications
  • Includes rubber o-ring seal/gasket
  • Incorporates pressure relief valve
See More

Mr. Gasket – Rear Main Seal Gasket (Part No.1960)

Rear Main Seal Gasket

from

$23.99
This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:
  • Repairs That Leaky Rear Main Sail
  • Silicone Rubber to Withstand Extreme Engine Oil Temperatures
  • Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
  • Injection Molded for Precise Fit
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1884 R)

PERFORMANCE OIL PAN GASKET SET

from

$64.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Rigid core, molded silicone rubber gaskets utilize the one-piece molded rubber technology for a perfect fit, ease of installation and include compression limiters to prevent overtightening.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Engine Timing Cover Gasket (Part No.2335)

Engine Timing Cover Gasket

from

$20.29
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Steel core gasket construction
  • Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8 (Part No.5002)

Torker-Plus Camshaft Kit for 1957-1986 Small-Block Chevy 283-400 V8

from

$411.99
Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:
  • Designed for 2500 to 6500 Performance
  • Designed for Hi-Perf Street; Drag or Marine Use
  • Matched to Edelbrock Torker II Intakes
  • Includes Hydraulic Lifters and Assembly Lube
  • Dyno Matched/Street Proven Performance
  • Take The Guesswork Out Of Camshaft Selection
See More

Competition Cams – CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA (Part No.12-250-3)

CAMSHAFT, SBC 284 XTREME ENERGY HYDRAULIC 1 EA

from

$258.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:
  • Excellent performance in street carbureted applications.
  • More vacuum allows an increase in duration for improved performance and assists power brakes.
  • Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
  • Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4377)

Cylinder Head Dowel Pins

from

$17.79
Big Block Chevrolet tubular head dowel, .638/.639 inch o.d. (outer diameter) by 1/2 inch. Packaged two per set. These hard to find dowel pins are precision machined then case hardened for accurate alignment in engine assembly.

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

Mr. Gasket – Cylinder Head Dowel Pins (Part No.4375)

Cylinder Head Dowel Pins

from

$14.99
Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:
  • Precision Machined
  • Case Hardened
  • Give Accurate Alignment
  • 2 Per Set
See More

Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.6561)

Ultra Seal: Oil Pan Gasket

from

$68.99
High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:
  • Steel core provides rigidity, durability and prevents gasket push out
  • Molded rubber coating seals minor irregularities in pan surface
  • One piece design is easier to install and even less prone to leak
  • Direct replacement suitable for all uses – street, racing, heavy duty
  • Include both gasket and new oil pan bolts
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1640)

Engine Valve Cover Gasket Set

from

$22.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Intake Gasket Set – Standard Duty – Big Block Chevy With Stock Rectangle Ports – 1.75"W X 2.50"H (Part No.108)

Intake Gasket Set - Standard Duty - Big Block Chevy With Stock Rectangle Ports - 1.75"W X 2.50"H

from

$29.99
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. Comes complete with front & rear manifold end seals. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Die-cut for an excellent fit
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals & distributor gaskets if applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Mr. Gasket – Intake Gasket (Part No.116)

Intake Gasket

from

$40.19
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material.
  • Provides excellent sealing and durability.
  • Can be trimmed if necessary for modified port applications.
  • Complete with manifold end seals and distributor gasket.
  • For OE replacement, high performance street, drag race and oval track use.
See More

Mr. Gasket – Advance And Retard Cam Bushings (Part No.85)

Advance And Retard Cam Bushings

from

$42.49
With Mr. Gasket cam degree bushings you fine tune the camshaft timing of your engine to as little as 1 degree. Even aftermarket timing sets with multiple keyways can’t give the range of adjustment these bushings allow. Retard your camshaft to lower the powerband for more low end torque and midrange horsepower, or advance for more top end power. This kit does even number adjustment 0-8 degrees.

Product Features:
  • Advance the cam for increased torque and horsepower
  • Tune your powerband for more end torque or increase top end horsepower
  • Includes (4) offset bushings and (1) 0 degree bushing
  • Cam sprocket dowel pin hole must be drilled to .406¿ (13/32¿) dia.
  • Cam sprocket dowel pin hole must be drilled to .406┐ (13/32┐) dia.
  • Increase Top-End Horsepower
See More

Edelbrock – TIMING CHAIN (Part No.7844)

TIMING CHAIN

from

$29.99
Product Features:
  • Timing Chain Only
See More

Edelbrock – Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy (Part No.2703)

Performer EPS Intake Manifold w/ Oil Fill Tube for 1955-86 Small-Block Chevy

from

$322.99
Edelbrock part #2703 Performer EPS intake manifold is designed for 1986 and earlier 262-400 cubic-inch Chevys. Edelbrock’s Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent thro

Product Features:
  • Idle-5500 RPM Range
  • Dual Plane Type-4150 Style Flange
  • 3.74 in. Front Height, 4.27 in. Center Height, 4.8 in. Rear Height
  • Satin Finish
  • Non-EGR W/ Oil Fill Tube
See More

Edelbrock – Street Tunnel Ram Small Block Chevy Intake Manifold (Part No.7110)

Street Tunnel Ram Small Block Chevy Intake Manifold

from

$631.99
For 3500 to 7500 PRM. Use where low-end torque is not a prime factor. Great for engines with slightly modified heads. HEI ignition will not clear manifold. Street machines, street rods, pro-street and marine.

Product Features:
  • For 3500 to 7500 RPM
  • Use Where Low-End Torque is Not a Prime Factor
  • Great For Engines w/Slightly Modified Heads
  • Top Has Vacuum Outlet for Power Brakes
  • Will Accept Forward and Sideways Mounted Carbs
  • Carburetor Center-to-Center Dimensions 8.875 in
  • HEI Ignition Will Not Clear Manifold
  • For Street Mach.; Street Rods; Pro-Street; Marine
See More

FEL-PRO Performance – Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts (Part No.1003)

Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts

from

$39.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
  • NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
  • SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
  • STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
  • DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
See More

Mr. Gasket – Ultra Seal: Head Gasket (Part No.5788G)

Ultra Seal: Head Gasket

from

$75.99
Mr. Gasket Ultra-Seal Head Gaskets are a five layer (graphite core/perforated steel outer layers) composite construction. The graphite core has excellent thermoconductivity (transfers heat) away from hot spots in head preventing gasket burn-out. They provide excellent stability, compressibility and high temperature endurance. A high temperature silicone coating ensures sealing of engine fluids. Compatible with cast iron or aluminum heads, they will not brinell (indent) aluminum cylinder heads. Suitable for high performance street, drag race and oval track use. Sold individually.brbrGasket Bore 4.230 inch, Compressed thickness 0.038 inch

Product Features:
  • Five layer (graphite core/perforated steel outer layers) composite construction
  • Graphite core has excellent thermo-conductivity-transfers heat away from hot spots in head preventing gasket burn-out
  • Provides excellent stability, compressibility and high temperature endurance
  • Coated with high temperature silicone to ensure sealing of engine fluids
  • Will not brinell (indent) aluminum cylinder heads
  • For high performance street, drag race and oval track use
  • Compatible w/High Octane Fuel
  • Compatible With Exotic Fuel
See More

Edelbrock – Water Pump Big-Block Chevy Standard/Long in Polished Finish (Part No.8861)

Water Pump Big-Block Chevy Standard/Long in Polished Finish

from

$475.99
Maximum cooling for street and racing engines. Internal passages are balanced for maximum flow. Impeller is larger than others for maximum pressure. Impeller vanes dramatically increase flow rates. Equal distribution to both sides of block. Only flows in one direction for optimum efficiency. In the early days of the automotive performance industry, you either ran what was available, or you fabricated something you thought met your needs. Such needs were the building blocks of this industry, and it was through the efforts of many that we have the automotive aftermarket, but it was through the work of one name in particular to which many in the industry owe a great debt, and that name is Edelbrock.

Product Features:
  • Maximum Cooling for Street and Racing Engines
  • Internal Passages Are Balanced for Maximum Flow
  • Impeller is Larger than Others For Max Pressure
  • Impeller Vanes Dramatically Increase Flow Rates
  • Equal Distribution to Both Sides of Block
  • Only Flows in One-Direction for Optimum Efficiency
See More

Weiand – Action Plus Water Pumps (Part No.9208P)

Action Plus Water Pumps

from

$215.99
Weiand’s light weight, performance aluminum mechanical Action-Plus water pumps give a weight saving of 30 percent to 50 percent over stock cast-iron pumps. These pumps feature a premium quality bearing and seal that have twice the load capacity of stock pumps. Weiand’s exclusive housing counter bore keeps the bearing form walking out. All pumps are designed with the necessary bracket bosses and water connections to fit popular street applications.

Product Features:
  • Twisted Snout Water Pump Design For Updated Style
  • Street Performance
  • Heavy Duty Shaft w/5/8 in. Pilot
  • Six-Blade Stamped Steel
  • Anti-Cavitation Impeller
  • 100 Percent Leak Tested
See More

B & M – Holeshot 3600 (Part No.20425)

Holeshot 3600

from

$825.99
HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
  • Dual Pattern Drive Lugs
  • New Turbine Hub
  • New Springs/Rollers In Stator
See More

B & M – Torque Converter, Holeshot 3000 (Part No.70421)

Torque Converter, Holeshot 3000

from

$789.99
The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some GM Holeshots.

Product Features:
  • Furnace Brazed Impeller
  • Steel Alloy Pump Drive Tube
  • Heavy Duty Needle Bearing
  • Between Stator and Turbine
  • Furnace Brazed Turbine
See More

1982 Chevrolet Camaro Performance Engines

Maybe you’re in the middle of a full rebuild of that 1982 Chevrolet Camaro. Maybe you just need a couple of Performance Engines. Either way, Advance Auto Parts has 81 different Performance Engines in our inventory ranging from $14.99 to $704.99. That means you can find the exact parts or products you need to keep that 1982 Chevrolet Camaro running smoothly.

Performance Engines are only as good as their brand. We stock 7 different brands to make sure you have plenty of trusted parts to choose from for your 1982 Chevrolet Camaro. Mr. Gasket, Edelbrock, and FEL-PRO Performance are just some of the brands we stock. Search for brands you know or compare prices and reviews to help you decide!

We know you’ll find the perfect Performance Engines for your 1982 Chevrolet Camaro, but don’t take our word for it – read our customer ratings and reviews and buy with confidence. Out of the 85 reviews in this category, some of the top rated parts include Action Plus Water Pumps with 3.7 stars and Action Plus Water Pumps with 1.5 stars.

So if you’re in the market for aftermarket Performance Engines to keep your 1982 Chevrolet Camaro rolling for years to come, look no further. Shop online and have your products shipped direct to your door, or pick up at the nearest Advance Auto Parts location today!

Performance Engines Brands To Make Your 1982 Chevrolet Camaro Last

Simple repair, complete replacement, or a full rebuild. No matter the job, your 1982 Chevrolet Camaro demands trusted brand parts and products to keep it running. Many trusted brands of Performance Engines make up Advance Auto Parts’ inventory, and all are ready to help make your Camaro the best it can be. Be sure to browse some of our top Performance Engines brands and parts.

Popular Competition Cams Performance Engines

We carry Competition Cams parts in our stock across Performance Engine Rocker Arms categories, plus more. For a 1982 Chevrolet Camaro, our most popular Competition Cams Performance Engines include:
MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST
from $213.99
(1)
MAGNUM ROLLER ROCKERS, SMALL BLOCK CHEVY 1.52 1 ST
Performance Engine Rocker Arms

Top 1982 Chevrolet Camaro Performance Engines from Mr. Gasket

Mr. Gasket products are another trusted brand when it comes to Performance Engines for your 1982 Chevrolet Camaro. Popular Mr. Gasket parts include:
High Performance 180 Degree Thermostat for Increased Flow
from $26.99
(20)
High Performance 180 Degree Thermostat for Increased Flow
Performance Engine Coolant Thermostats

FAQs for 1982 Chevrolet Camaro Performance Engines

What are the most purchased Performance Engines for the 1982 Chevrolet Camaro?

Out of 81 Performance Engines for the 1982 Chevrolet Camaro, the most popular in our inventory are:
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
from $195.99
(7)
Performer EPS Intake Manifold for 1955-86 Small-Block Chevy
Performance Intake Manifolds
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
from $39.49
(1)
Cylinder Head Gasket: Multi-Layered Steel, Without Head Bolts
Performance Engine Cylinder Head Gaskets
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
from $52.99
(1)
Cylinder Head Gasket: Steel Core Composite, Without Head Bolts
Performance Engine Cylinder Head Gaskets

What are the top-rated 1982 Chevrolet Camaro Performance Engines?

Top-rated Performance Engines for your 1982 Chevrolet Camaro based on customer reviews/ratings are:
Action Plus Water Pumps
from $215.99
(3)
Action Plus Water Pumps
“I bought this item for my 1979 Camaro SBC for Street/Strip application. Water pump weighs 4 LBS less than factory, comes with its own cork gaskets. N”
Action Plus Water Pumps
from $215.99
(2)
Action Plus Water Pumps
“The twisted neck comes to far up on the hub. For a 2 groove pulley it causes the pulley to hit the water pump. You will also need new bolts for the”
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
from $329.99
(1)
Performer Intake Manifold for 1987-95 Small Block Chevy, Satin Finish
“product fit as described , no complaints”