1980 Jeep J10 Performance Engines

Product Features:

• Case-Hardened Tubing
• Surface Hardening
• Welded Ends
• 0.3125 in. Diameter
• Use with or without Hardened Steel Guideplates

Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

• For Use With Cast Iron Heads
• Springs Made of Highest Quality Spring Wire
• Springs Precision Wound To Close Tolerances
• Use with Original Equipment Heads Only

Edelbrock #8832 Water Pump AMC long style 1973-later ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cooling” Water Pumps

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 4.1875 in. Block To Hub Height
• Satin Finish

HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) APPLICATION: HoleShot 3600 for GM 1965 to 1991 TH400, 425, 375 and 1968 to 1981 TH350, 375B (not 350C) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• Dual Pattern Drive Lugs
• New Turbine Hub
• New Springs/Rollers In Stator

The Holeshot Converter is a very good choice for the typical street machine that is looking for better launch capability and more strength. With a furnace brazed turbine, New turbine hub and dual pattern drive lugs on some Holeshots.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• Metal Outer Rubber Inner
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Are you rebuilding an engine and need a fresh set of piston rings? Omix-ADA offers high-quality replacement piston ring sets from Standard to .080 thousandths over size. They will give you years of service and get you back on the road.

Product Features:

• .060 Over
• Engine Work May Be Required To Install This Part
• Limited 5 Year Warranty

The Edelbrock #7372?head gaskets provide the best sealing solution and are matched to Edelbrock cylinder heads for optimal performance. Edelbrock relies on industry leading head gasket manufactures to ensure our head gasket sets will provide the best fit

Product Features:

• Head: 4.275″ Bore/0.045″ Thick/10.60cc Vol.
• Intake: 1.13″x2.21″ Port/.030″ Thick
• Exhaust: 1.80″x1.30″ Port
• 3/16″ Valve Cover
• Multi Piece Configuration

Are your Jeep’s cylinder head gaskets leaking? Or, are you rebuilding an engine and need fresh gaskets? Omix-ADA offers high-quality replacement cylinder head gaskets that will give you years of service and get you back on the road.

Product Features:

• Composite
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Is your Jeep’s cylinder head gasket leaking? Or, are you rebuilding an engine and need a fresh gasket? Omix-ADA offers high-quality replacement cylinder head gaskets that will give you years of service and get you back on the road.

Product Features:

• Composite
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Product Features:

• Designed for Optimum Torque and Acceleration
• Maximum Performance From Idle through Mid-Range
• Matched To Performer Intakes PN[2131/3731]
• Includes Hydraulic Lifters and Assembly Lube
• Major Improvement in Throttle Response and Torque
• Use For Daily Drivers/Trucks/Vans/RVs/4x4s
• Take The Guesswork Out Of Camshaft Selection

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Not for Stock Motorcraft Spread Bore Carburetor
• Two Center Bolt Holes are Offset

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used
• Not for Stock Motorcraft Spread Bore Carburetor
• Two Center Bolt Holes are Offset

Product Features:

• For Idle to 5500 RPM Street-Driven Performance
• Dual-Plane Low-Rise Intake w/180 deg. Firing Order
• Patented Runner Design Ensures Broad Torque Curve
• Excellent Throttle Response and Mid-Range Power
• 50-State Street Legal if Correct Carburetor Used

Timing chains stretch over time. If left untouched, they can begin jumping teeth on the camshaft and crankshaft sprockets. This will change your timing and will do major damage to your Jeep’s engine. It is recommended that you change the timing chain and

Product Features:

• 3 Piece Kit
• OE Style
• Direct Fit
• Limited 5 Year Warranty

Direct OE replacement Jeep parts and accessories built to the original specifications by Omix-ADA. Limited five year Manufacturer’s warranty.

Product Features:

• OE Style
• Direct Fit
• Highly Durable
• Long Lasting
• Limited 5 Year Warranty

Are you rebuilding an engine and need a fresh set of pistons? Omix-ADA offers high-quality replacement pistons from Standard to .080 thousandths over size. Wrist pins included. They will give you years of service and get you back on the road. Sold individ

Product Features:

• .020 Over
• Engine Work May Be Required To Install This Part
• Limited 5 Year Warranty