1979 Ford F-250 Differentials

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years. This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 35 spline axles
• 4.10 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

Product Features:

• Brand may vary by location

Product Features:

• Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
• Fits standard open differentials only

Yukon replacement yoke for Dana 30, 44, and 50 with fine spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 44
• 26 spline
• 1310 u-joint size
• 3.219″ snap ring span
• 1.062″ cap diameter
• Outside snap ring design
• Strap style

Pinion gear thrust washer for 9.75″ Ford.

Product Features:

• Pinion gear thrust washer
• Fits Ford 9.75″

Product Features:

• Seal housing for Dana Spicer 44
• Includes o-rings

Product Features:

• DANA-60 R/P 5.38 THICK REV MG (USES PRE-LOAD SHIMS)

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.

Product Features:

• Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
• 7/8″ x 20 thread
• 1 1/8″ socket

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Replacement crush sleeve for Dana 44 & Dana 50 APROX 2.650″ long.

Product Features:

• Crush sleeve for Dana Spicer 44 and 50
• 2.650″ tall

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• KIT BRG.& SEAL FORD 10.25

Product Features:

• Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″

Product Features:

• Bulkhead fitting kit
• Includes bulkhead fitting, outer fitting and o-ring

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
• For Trac Loc positraction applications only

Product Features:

• Ford 10.25″RING GEAR BOLT 1.33″ O.A. 1″ THREADS

Product Features:

• Floater roll pin
• Fits Dana Spicer 44 and Chrysler 8.75″
• Powr Lok positraction only

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

• Fits Dana Spicer 44 with 30 spline axles
• 3.92 and up ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

Product Features:

• INSTLTN KIT-DANA 60 & 61

Right hand inner 4340 Chrome Moly replacement axle shaft for Dana 44, ’75-’79 Ford F250, uses 5-760X u/joint. 34.75″ long with 30 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

• Fits 1978-1979 Ford F250 front with Dana Spicer 44
• 4340 Chromoly
• Right hand side inner
• 30 spline
• 34.75″ from end of splines to center of u-joint bore

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Product Features:

• Spider gear kit
• Fits Dana Spicer 60, 30 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Product Features:

• Inner oil slinger for Dana Spicer 60