1979 Ford F-150 Differentials

Product Features:

• Shim kit
• Fits Ford 8.8″, 1963-1979 Corvette, GM 12 bolt passenger car and truck, 8.2″, 8.5″ and 8.6″ Dura Grip positraction

Flat side gear without hub for 8″ and 9″ Ford with 28 splines.

Product Features:

• Side gear without hub
• Fits Ford 8″ and 9″ Trac Loc positraction with 28 spline axles

Yukon Extra HD 3.062″ nodular Iron dropout for Ford 9″. Yukon nodular iron dropouts feature a 5/8″ cap bolt and forged caps for maximum strength. Rated up to 1200HP!

Product Features:

• Fits Ford 9″
• 3.062″ carrier race diameter
• Nodular iron for added strength

Valvoline is the No. 1 ATF brand, and now we’ve taken it to the next level with our hybrid performance fluid: Valvoline Full Synthetic Hybrid Automatic Transmission Fluid. Specifically designed for hardworking hybrids, Valvoline Full Synthetic Hybrid ATF is suitable for use in more than 95% of hybrid vehicles in operation with registered US ATF full hybrid vehicles (not including mild hybrids, traditional CVT or DCT hybrid models). Valvoline Full Synthetic Hybrid ATF is proven to maximize transmission life, and it’s compatible with copper and the coatings on copper in hybrid transmission, providing greater oxidation stability, insulation for the electrical current, and increased heat transfer capabilities to protect against transmission failure. Look for Valvoline’s complete lineup of hybrid performance fluids, including motor oil and antifreeze/coolant ¿ from the brand trusted for over 150 years.

Product Features:

• Full synthetic hybrid ATF with Copper Care Technology, from the No. 1 ATF brand
• Enhanced protection against corrosion that can result in hybrid transmission failure
• Protects electrical systems maximizing transmission efficiency
• Increased heat transfer capabilities to protect against higher temperatures produced by hybrids

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 2011 and up Ford 8.8″ in F150
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

Side gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Side gear thrust washer for Ford 8.8″
• 0.750″ diameter cross pin shaft applications only

DiffrlPinSupport

Adjuster lock bolt 3.062″ & 3.250″ Yukon Ford 9″ Drop Out.

Product Features:

• Side adjuster lock bolt

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

STAR washers, 3.250″ Yukon Ford 9″ Drop Out new design ONLY.

Product Features:

• Star washer
• Fits Ford 9″
• 3.250″ designs only

Fine thread pinion support bolt (aftermarket aluminum only) for 9″ Ford.

Product Features:

• Pinion support bolt for Ford 9″
• 3/8″ x 24 thread
• 1.5″ long

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

• 35 spline
• 8 x 3.96″ bolt pattern
• Cut to length design fits 40″-43.5″ applications
• Fits Dana Spicer 60, 70 and 80

B&M Cast Aluminum Differential Covers are designed to strengthen the differential by preventing case distortion and ring gear & bearing cap deflection. Constructed of A356.0-T6 aluminum, these rugged covers significantly increase the fluid capacity and dissipate heat much faster than the stock factory unit to prolong the life of your ring and pinion gears. Additional features include an engraved B&M logo, drain and fill port locations, a magnetic drain plug for catching ferrous metal particles, and complete hardware and installation instructions.

Product Features:

• Additional Oil Capacity
• More Cooling Ability
• No Dipstick Modification
• Some Include Fluid Pickup Extension
• Built-In Drain Plugs
• Cast Aluminum

Our wheel seals are engineered using only the highest-quality materials to meet vehicle manufacturer specificatons. We work with suppliers to design seals that meet FAG’s quality standards. Seals are designed to protect wheel end components from contamination – such as dirt, dust, and moisture – and prevent the loss of grease over the life of the bearing. The specifications for wheel seals are very demanding, and the type required depends on the specific application, position and vehicle class.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

9″ Ford Spartan locker cross pin, short.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Ford 9″
• Works with Spartan Locker or standard open spider gears
• Short shaft for four pinion designs

3.062″ side adjuster, Only Fits Yukon Ford 9″ Drop Out, new design ONLY.

Product Features:

• Side adjuster
• Fits Ford 9″
• 3.062″ designs only

Product Features:

• Seal housing for Dana Spicer 44
• Includes o-rings

Yukon Trac Loc positraction, Ford 8.8″, 31 spline, with Carbon Fiber clutches.

Product Features:

• Trac Loc positraction carrier case
• Includes spider gears
• Fits Ford 8.8″ with 31 spline axles
• Carbon fiber clutches

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits 2008-2010 Ford 9.75″ housing with 2011 and newer ring and pinion set
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve, thread locker, marking compound with brush, and gasket.

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Pinion gear thrust washer
• Fits Ford 8.8″
• 0.750″ I.D.

Product Features:

• Crush sleeve
• Fits Ford 9.75″
• Conversion crush sleeve to install 2011 and up ring and pinion set into 2000-2010 housing

High-quality Differential Component Shim

Product Features:

• SHIM KIT FITS-8.25-F7.5-AMC20-GM0

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread