from

$21.99

8.75″ Chrysler & 9″ Ford preload shim kit.

Product Features:

Preload shim kit for Ford 9″ and Chrysler 8.75″ with ’41’ and ’42’ case housing

from

$616.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Ford 8.8″ with 31 spline axles and 7/8″ cross pin shaft
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$125.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 44 differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Dana Spicer 44
Includes carrier bearings and races and carrier shim kit

from

$175.99

9″ large solid pinion preload spacer & shim kit for 35 spline pinion.

Product Features:

Crush sleeve eliminator kit for Ford 9″ with 35 spline pinion

from

$21.99

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
Left hand thread

from

$383.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Ford 9.75″
Install 2011 and up Ring & Pinion into 2000 – 2007
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$194.99

Differential Carrier

from

$31.99

Product Features:

MINI SPOOL 8″ & 9″ 31 SPLN STL 090431

from

$4.99

Dana 44, GM55P & 8.2″ GM pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer for Dana Spicer 44, GM 8.2″ and 1955-1964 GM passenger car

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$12.99

Product Features:

Cover gasket
Fits Dana Spicer 44

from

$615.99

Yukon Extra HD 3.062″ nodular Iron dropout for Ford 9″. Yukon nodular iron dropouts feature a 5/8″ cap bolt and forged caps for maximum strength. Rated up to 1200HP!

Product Features:

Fits Ford 9″
3.062″ carrier race diameter
Nodular iron for added strength

from

$36.99

Product Features:

Belleville plate, splined
Fits Dana Spicer 44 Powr Lok

from

$13.59

Product Features:

FORD 9″ CROSS PIN

from

$299.99

Yukon standard open spider gear kit for 8.8″ Ford with 31 spline axles and 7/8″ pin. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fits Ford 8.8″ with 31 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.
0.875″ cross pin shaft diameter

from

$399.99

Yukon positraction internals for Dana 44 Dura Grip posi, 30 spline. Does not include clutches. Does NOT fit Trac Loc or Powr Lok. Fits Dura Grip ONLY.

Product Features:

Spider gear kit
Fits Dana Spicer 44 with Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$203.99

Yukon yoke for Ford 9″ with 28 spline pinion and a 1330 U/joint size. 5″ length. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Ford 9″
28 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.125″ cap diameter
U-bolt style

from

$188.99

Bearing race driver for Dana 44 rear. (TK 31520) No return.

Product Features:

Bearing race driver
Fits 31520 race
All steel construction

from

$5.99

Ford 7.5″ & 8.8″ ring gear bolt, standard Open & TracLoc. 7/16″ x 20.

Product Features:

Ring gear bolt for Ford 7.5″ and 8.8″
7/16″ x 20

from

$10.99

Replacement pinion nut for Model 20 & 35, Dana 30 JK, 44 JK front, Ford 10.25″, 10.5″ & some 9.75″. 7/8-20 thread, 1 1/8 socket.

Product Features:

Pinion nut for Jeep JK front, Jeep Liberty front, Ford 9.75″, 10.25″, 10.5″ and AMC Model 20 and Model 35
7/8″ x 20 thread
1 1/8″ socket

from

$44.99

3 Qt. Penzoil 80W90 conventional gear Oil.

Product Features:

Includes three quarts of conventional oil

from

$8.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$3.99

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

from

$52.99

Cross pin shaft (0.875″) for ’86 and newer 8.8″ Ford.

Product Features:

Cross pin shaft for Ford 8.8″
0.875″ diameter

from

$482.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits 2000-2007 Ford 9.75″
Requires 2011 and up Ring and Pinion set
Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.

from

$6.99

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features: