1978 Ford E-150 Econoline Differentials

9″ Ford pinion nut, 35 spline Large pinion oversize.

Product Features:

• Pinion nut
• Fits Ford 9″ with 35 spline pinion

Yukon Trac Loc internals for 8″ & 9″ Ford, 31 spline, includes hub & clutches. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Ford 9″ with Trac Loc positraction with 31 spline axles
• Includes two side gears, four pinion gears, cross pin shaft, clutch hub, roll pin and spider gear thrust washers.

The Yukon Zip Locker is the latest in on-demand traction. Its air-operated design allows you to switch from an open differential to 100% lockup when you need it, giving you the ultimate in driver selectability. The Yukon Zip locker is an air operated locker that provides selectable traction for off road or street use. This unit features 4320 Chrome Moly internals for added strength. Assembled in the USA! compressor sold separately. All Zip Lockers are backed by the best warranty in the business! All Zip Lockers come with a six (6) year warranty, including any collaterally damaged parts and associated labor, up to $2,000, for the first two (2) years.

Product Features:

• Fits Dana Spicer 44 with 30 spline axles
• 3.73 and down ratio only
• Forged case and 8620 internals for added strength
• Works with a variety of air delivery systems
• Assembled in the USA

Chrome cover for 9.75″ Ford.

Product Features:

• Fits Ford 9.75″
• Chrome

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Yukon forged yoke for Ford 9″ with 35 spline pinion and a 1350 U/joint size (stronger than billet). 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 9″
• 35 spline
• 1350 u-joint size
• 3.625″ snap ring span
• 1.188″ cap diameter
• Outside snap ring design
• U-bolt style

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 44 and Toyota 8″ and V6

Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.

Product Features:

• Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
• Left hand thread

Mr. Gasket Axle Housing/Differential Cover or Rear End Gaskets are manufactured from a .047 inch thick cellulose/nitrile composite gasket material for excellent sealing and durability. They are precision die-cut for an excellent fit. Fits 1957-1981 Ford 10 bolt 9 inch ring gear.

Product Features:

• .047″ thick cellulose/nitrile composite gasket material
• Precision die cut
• Reusable

8″ & 9″ Ford 5-Tab clutches (early Equalock).

Product Features:

• Clutch kit
• Fit Ford 9″ Equa Loc positraction
• 5 outer tabs

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

Set-up carrier bearing (2 bearings, no races) 25590. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 44
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM89410 race
• All steel construction

Product Features:

• Carrier shim kit for Dana Spicer 30 and Dana Spicer 44 with 19 spline axles

Pinion gear thrust washer for 8″ and 9″ Ford, Model 20, and 7.25″ Chrysler.

Product Features:

• Pinion gear thrust washer for Ford 8″, Ford 9″ and Chrysler 7.25″

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Ford 9.75″
• Included are pinion bearings and races, pinion seal, pinion nut, crush sleeve, complete pinion shim kit, and marking compound with brush.

Product Features:

• Inner oil slinger for Dana Spicer 25, 27, 30, 44 and 50

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

• Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
• 3/8″ x 24 thread

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000!

Product Features:

• Fits Ford 8.8″ with 31 spline axles
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Product Features:

• DANA 44 R/P 3.92 STD MG

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• Meets or exceeds OE specifications

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Product Features:

• Cover gasket
• Fits Dana Spicer 44

Product Features:

• Spider gear kit
• Fits Ford 8″ and 9″ 28 spline open differential
• Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses carrier bearings & races with an I.D. of 1.625″ and an O.D. of 2.891″. This kit uses Timken bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Ford 9″ with LM501310 carrier race
• Included are Timken bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , thread locker, marking compound with brush, and gasket.

Product Features:

• NODULAR HOUSING 9″ FORD 3.25″ BORE

This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

Product Features:

• Super carrier shim kit for Ford 8.8″, GM 12 bolt passenger car and truck, GM 8.0″, 8.6″, 8.6″ IRS and 1963-1979 Corvette
• Interlocking design makes installation much easier