from

$80.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$67.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
For Engine with One-Piece Fuel Pump Eccentric

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
Not intended for use in emission controlled vehicles.

from

$23.99

Spectre’s Ford small block water neck fits 1965 – 19475 Ford 221, 289, 302 and 351W engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes the bolts and sealing O-ring, and also features a 1/2 inch outside diameter by-pass hose connection.

Product Features:

Fits 1965 – 19475 Ford 221, 289, 302 and 351W engines
Includes bolts and sealing O-ring
Has additional 1/2 inch by-pass hose fitting
Chrome plated
Designed for OEM fit
Easy to install

from

$24.99

Precision die-cast, these water necks or thermostat housings are first polished to a high luster, then chrome plated. Features an o-ring style seal to prevent water leaks. Comes with o-ring gasket and mounting bolts.

Product Features:

Chrome plated
Features an O-Ring style seal to prevent water leaks
Includes O-Rings andmounting bolts

from

$54.99

Spectre’s Ford V8 water neck fits Ford 429 – 460 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes sealing O-ring, and has a 3/8 inch NPT threaded hole for the Ford temp sensor.

Product Features:

Fits Ford 429 – 460 engines
Has a 3/8 inch NPT threaded hole for temperature sensor
Includes sealing O-ring
Chrome plated
Easy to install
Hardware not included

from

$28.99

Product Features:

Clean Positive Seal
Embossed Silicone Bead Surrounding The Port
Matched To Manifolds And Cylinder Heads

from

$38.59

Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:

Manufactured from cellulose/nitrile composition gasket material
Provides excellent sealing and durability
Silicone beading on both sides of each gasket
Complete with manifold end seals and distributor gasket
For OE replacement, high performance street, drag race and oval track use
Creates Tight Leak proof Seal

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

from

$31.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$30.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$59.19

High performance, race quality gasket with molded rubber coating over a steel core. Steel core provides rigidity and durability, preventing prevent push out while the molded rubber coating helps seal minor oil pan rail irregularities. The one piece design eliminates the need for separate end seals to make installation easier and even further reduce the possibility of oil leakage. Provides excellent sealing and durability. Excellent replacement for stock original equipment, high performance street, drag race and oval track. Includes gasket and new oil pan bolts.

Product Features:

Steel core provides rigidity, durability and prevents gasket push out
Molded rubber coating seals minor irregularities in pan surface
One piece design is easier to install and even less prone to leak
Direct replacement suitable for all uses – street, racing, heavy duty
Include both gasket and new oil pan bolts
No Cork Particles
Easy Removal For Disassembly

from

$32.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
With steel core to provide ultimate excellent blowout resistance.
Not intended for use in emission controlled vehicles.

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$27.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 195 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$788.99

Dual Valve Springs from COMP Cams are manufactured from Super Clean wire and subject to extensive quality control testing to deliver a valve spring assembly with superior strength, durability and valve train stability, no matter what the application. The dual spring design creates a stronger valve spring that can easily handle the increased lift found in extreme stress applications. COMP Cams Dual Valve Springs exceed the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 112 lbs. @ 1.900″, Open Pressure: 355 lbs. @ 1.200″
O.D.: 1.509″, I.D.: 0.697″
Dual valve springs with damper

from

$52.99

Product Features:

Non-Rotator Type
1.384 in. Outer Diameter
1.020 in. Inner Diameter
1.020 in. Coil Blind
Set of 16

from

$299.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal
Available in Multiple Finishes

from

$772.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Improve performance on the street or race track. Larger cross-sectional area and taller card flange. Compatibility with lar

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed For 1500 To 6500 RPM
Designed For Street And High Performance
Larger Cross Sectional Area
Taller Carb Flange
Compatibility w/Large Displacement 351W Based Eng.

from

$349.99

New Everbright(TM) Manifold coating now available on the most popular Weiand and Holley intakes uses proprietary vacuum metalizing technology combined with a protective clear powdercoat to provide long lasting, virtually maintenance free polished looks.

Product Features:

Low Rise/Dual Plane Design For Maximum Torque
Permanent Mold Casting Process
Lighter/Smoother/Better Looking/Consistent Casting
Dyno Proven To Make 25hp Over Competition
Fully CNC Machined For A Perfect Fit
Square Bore Carburetor Flange
Exhaust Crossover For Improved Street Drivability

from

$579.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 deg. Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal

from

$468.99

Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Improve performance on the street or race track. Larger cross-sectional area and taller card flange. Compatibility with large displacement 351W based engines. For 4 bbl carbs. Available in cast, polished and endurashine finish.

Product Features:

Based on Performer RPM-Series with Unique Air Gap
Air Gap Cooler and Denser Mixture for More Power
Designed For 1500 To 6500 RPM
Designed For Street And High Performance
Larger Cross Sectional Area
Taller Carb Flange
Compatibility w/Large Displacement 351W Based Eng.

from

$186.99

Product Features:

Head: 4.500″ Bore/0.048″ Thick/12.5cc Vol.
Intake: 1.98″x2.26″ Port/.060″ Thick
Exhaust: 1.50″x2.10″ Port
5/16″ Valve Cover
Multi Piece Configuration

from

$49.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$41.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
Raises combustion sealing force to roughly three times that of standard head gaskets.
Steel wire rings for the greatest combustion seal strength.
Not intended for use in emission controlled vehicles.

from

$52.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

from

$51.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces

1969 Ford F-250 Pickup Performance Engines

More 1969 Ford F-250 Pickup Performance Engines

Essential 1969 Ford F-250 Pickup Performance Engines

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7808)

Edelbrock – Performer-Link Adjustable True-Roller Timing Chain Set (Part No.7820)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1614)

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1619)

Spectre – Water Neck (Part No.4232)

Mr. Gasket – Water Neck (Part No.2667)

Spectre – Water Neck; Ford 429-460 (Part No.4734)

Edelbrock – Intake Manifold Gasket for 302 E-Boss & 351W E-Boss Clevor Conversions (Part No.7265)

Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5831)

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1248)

Competition Cams – VALVE SEALS, TEFLON 3/8" 1 ST (Part No.505-16)

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1811)

Mr. Gasket – Ultra Seal: Oil Pan Gasket (Part No.6683)

FEL-PRO Performance – Oil Pan Gasket Set: High-Temperature Rubber-Coated Fiber, 5 Piece Set (Part No.1820)

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

Mr. Gasket – High Performance Thermostat (Part No.4365)

Competition Cams – VALVE SPRINGS, 1.509" DUAL 1 ST (Part No.924-16)

Edelbrock – Sure Seat Valve Springs for Ford 351W V8 (Part No.5882)

Edelbrock – Performer 289 Intake Manifold for Small-Block Ford (Part No.2121)

Edelbrock – RPM Air-Gap Small Block Ford Polished Intake Manifold (Part No.75811)

Weiand – Action +Plus; Intake Manifold (Part No.8010)

Edelbrock – Performer 289 Intake Manifold for Small-Block Ford, Polished Finish (Part No.21211)

Edelbrock – RPM Air-Gap Small Block Ford 351W Intake Manifold (Part No.7581)

Edelbrock – Engine Gasket Set (Head / Intake / Exhaust / Valve Cover) for Ford (Part No.7365)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1018)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1020)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-2)

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1011-1)

Popular 1969 Ford F-250 Pickup Performance Engines Categories

1969 Ford F-250 Pickup Performance Engines

Performance Engines Brands To Make Your 1969 Ford F-250 Pickup Last

Popular Competition Cams Performance Engines

Top 1969 Ford F-250 Pickup Performance Engines from Mr. Gasket

FAQs for 1969 Ford F-250 Pickup Performance Engines

What are the most purchased Performance Engines for the 1969 Ford F-250 Pickup?

What are the top-rated 1969 Ford F-250 Pickup Performance Engines?

More Popular Parts for All Makes