1968 Ford Galaxie Performance and Racing Products

Essential Performance and Racing Products for 1968 Ford Galaxies

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1812)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)

Blaster 2 Coil: High Performance Ignition Upgrade

from

$49.99
If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:
  • Improved output coil for electronic ignitions
  • Works w/Blaster Ignition Or MSD 5/6/7 Series
  • Ballast Resistor Required If Used w/Stock Points Ignition
  • Alkyd tower w/high dielectric properties lessens carbon tracking
See More

Energy Suspension – Strut Rod Bushing Set (Part No.4.7117R)

Strut Rod Bushing Set

from

$31.99
These performance polyurethane components help reduce common wheel roll-under. This occurs when stopping abruptly, especially when using performance tires for both front of rear drive vehicles is so equipped. Replaces that original, short lived and too-soft O.E.M, rubber on front wheel drive vehicles – diminishes wheel hop and traction loss during standing start accelerations. Better maintains proper alignment under extreme conditions. Made of Energy’s Hyper-Flex performance polyurethane to add both performance and durability.

Product Features:
  • Made from HYPER-Flex Polyurethane
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1020)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$41.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

Mr. Gasket – Ultra Seal: Intake Gasket (Part No.5831)

Ultra Seal: Intake Gasket

from

$38.59
Ultra-Seal intake manifold gaskets are manufactured from cellulose/nitrile composition gasket material. Provides excellent sealing and durability. Incorporates Silicone beading around each intake and water outlet port to provide additional sealing strength on both sides of each gasket. No gasket sealer required. For OE replacement, high performance street, drag race and oval track use. Includes manifold end seals and distributor gasket.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Silicone beading on both sides of each gasket
  • Complete with manifold end seals and distributor gasket
  • For OE replacement, high performance street, drag race and oval track use
  • Creates Tight Leak proof Seal
See More

Edelbrock – RPM Air-Gap Small Block Ford 351W Intake Manifold (Part No.7581)

RPM Air-Gap Small Block Ford 351W Intake Manifold

from

$468.99
Based on performer RPM-series with unique air gap. Air gap cooler and denser mixture for more power. Designed for 1500 to 6500 RPM. Improve performance on the street or race track. Larger cross-sectional area and taller card flange. Compatibility with large displacement 351W based engines. For 4 bbl carbs. Available in cast, polished and endurashine finish.

Product Features:
  • Based on Performer RPM-Series with Unique Air Gap
  • Air Gap Cooler and Denser Mixture for More Power
  • Designed For 1500 To 6500 RPM
  • Designed For Street And High Performance
  • Larger Cross Sectional Area
  • Taller Carb Flange
  • Compatibility w/Large Displacement 351W Based Eng.
See More

Edelbrock – Classic Series Valve Covers: Small Block Ford 221-351W 62-95, Black Aluminum (Part No.41603)

Classic Series Valve Covers: Small Block Ford 221-351W 62-95, Black Aluminum

from

$361.99
The Edelbrock part #41603 Classic Series Valve Covers are designed for Ford 221-351W V8 1962-95 applications and have a Black finish. Edelbrock first made these aluminum valve covers in the late ’50s and they’re still a classic. Made of heavy-gauge sand-cast aluminum, Overall height is measured from base to top at the highest point. Edelbrock classic valve covers can be machined to accept breathers if desired.

Product Features:
  • Small Block Ford 221-351W 62-95
  • Tall
  • Black Aluminum
  • Set Of Two
See More

Edelbrock – Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp) (Part No.70050)

Performer RPM Carb/Plate Nitrous Systems Square-Bore Carbs (100-250 Hp)

from

$735.99


Product Features:
  • Designed For Carbureted V8 Engines
  • Simple To Install
See More

FEL-PRO Performance – Engine Valve Cover Gasket Set (Part No.1639)

Engine Valve Cover Gasket Set

from

$26.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Blue Stripe performance cork-rubber gaskets use cork particles evenly distributed throughout a rubber binder resulting in a compressible gasket without leak paths.
  • Not intended for use in emission controlled vehicles.
See More

B & M – Automatic Shifter, Light Truck Megashifter (Part No.80680)

Automatic Shifter, Light Truck Megashifter

from

$479.99
The B&M Megashifter has it all, form, function and classic style. This all adds up to bring you a quality shifter that’s been one of the most popular automatic shifters of all time. The light truck Megashifter is better suited for truck and bench seat applications with its overall height of 14.85-inches tall (2.25-inches taller than #80690 Megashifter.) The positive ratcheting action won’t allow you to over-shift and miss a gear at that critical moment, along with the reverse lockout feature meets NHRA/IHRA safety rules for those weekend grudge races at the track, while the look and feel of the T-handle and accordion style shift boot really shows off its racing heritage. Other features include a black console that you can trim to match the contour of your vehicle’s floor, 5-foot long shifter cable, cable brackets, transmission shift levers, chrome plated top plate with lighted gear indicator and everything needed for an easy at home installation. An optional T-handle with a 12-volt button is available separately for actuating a trans-brake, nitrous oxide or other accessories for the hard-core performance enthusiast. This shifter fits most popular Chrysler, Ford and GM 3 and 4-speed automatic transmissions. Note: AOD transmissions require optional kit #40496, GM 4L60E through 4L85E transmissions with PRNDL switch will require optional kit #70499. Overall Dimensions – 14.9L x 6.4W x 14.8H

Product Features:
  • Universal Floor Mount Application
  • Cable Operated
  • Quick Installation
  • Accurate Shifting
  • NHRA/IHRA Reverse Lockout Meets Requirements
  • Use w/Reverse Pattern Valve Body
  • Includes Neutral Safety Switch
  • Includes Backup Light Switch
See More

Hooker Headers – Super Comp. Header (Part No.6130HKR)

Super Comp. Header

from

$834.99
Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • Long Tube Lengths
  • Long Transition Collectors
  • Monstrous Low-Mid Range Torque
  • Keep Top End Horsepower
  • Provides Finest Fit
  • Most Durable Design Available
See More

Hays – Flexplt: Bb Ford 70-97 (164T) (Part No.12-055)

Flexplt: Bb Ford 70-97 (164T)

from

$185.99
Flexplt: Bb Ford 70-97 (164T)

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

Mr. Gasket – Exhaust Gasket Set (Part No.253)

Exhaust Gasket Set

from

$29.49
Manufactured from high-temperature composite exhaust material. Provides maximum torque retention to eliminate gasket failure. Can be trimmed if necessary for modified port applications. Precision die cut for an excellent fit. For OE replacement, high-performance street, drag race and oval track.

Product Features:
  • High-Temperature Exhaust Material
  • Withstands Extreme Exhaust Heat
  • Excellent Sealing Durability And Torque Retention
  • Superior Tensile Strength
See More

MSD Ignition – Distributor; Ford 302; Pro-Billet; Small Cap (Part No.8579)

Distributor; Ford 302; Pro-Billet; Small Cap

from

$399.99
MSD engineers fit all of their high performance distributor experience into a special compact housing designed to be less obtrusive for Ford engines. The diameter of the special cap and housing are 5/8 inch smaller than stock Ford distributors providing extra room in front of the engine. The new MSD cap features spark plug style terminals and is firmly screwed down to the housing. The distributor relies on MSD’s race proven magnetic pick-up and precision reluctor to deliver accurate trigger signals to the MSD ignition throughout high rpm. The reluctor assembly is turned by a hardened steel shaft which rides in a sealed ball bearing for high rpm stability and endurance. Mounted to the top of this shaft is a fully adjustable mechanical advance assembly. The rate at which the chromoly assembly advances the timing is easily controlled by changing the supplied advance springs and stop bushing for total advance.

Product Features:
  • Billet housing 5/8 in. smaller dia. than stock Ford distributors
  • Must Be Used w/An MSD Ignition Control
  • Supplied w/small dia. cap w/HEI style terminals; race and rotor
  • Will accept PN[8441] Cap-A-Dapt
  • Nylon pads ensure smooth operation of the advance weights
  • Advance weight pins are staked and tig welded to the plate
  • Mech. advance assem. can be locked out for crank trigger systems
  • Advance plate and weights are fine blanked from chrome moly steel
See More

PerTronix – D660701 Rotor Flame-Thrower Billet Distributor (Part No.D660701)

D660701 Rotor Flame-Thrower Billet Distributor

from

$18.99
Rotor for Flame-Thrower cast distributors. Premium rotor with brass contact

Product Features:
  • PerTronix D660701 Rotor Flame-Thrower Billet Distributor
  • Rotor for Flame-Thrower cast distributors
See More

Richmond Gear – Differential Ring And Pinion (Part No.49-0027-1)

Differential Ring And Pinion

from

$344.99
Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:
  • For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
  • The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
  • Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
  • Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
  • Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.
See More

Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

Remote Oil Filter Kit

from

$97.99
This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:
  • Relocate oil filter to an easy access location
See More

Mr. Gasket – Thermocap Radiator Cap (Part No.2476BK)

Thermocap Radiator Cap

from

$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:
  • Indicates coolant temperature
  • Helps prevent coolant injuries
  • Fahrenheit and centigrade readings
  • Color-coded temperature ranges
  • Integrated coolant reclamation valve
  • Improves under-hood appearance
  • Chromed crown with a colored trim ring
See More

Holley – Mechanical Fuel Pump (Part No.12-460-13)

Mechanical Fuel Pump

from

$221.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • High Output Fuel Flow
  • Flows 130 gph Free Flow
  • Shutoff Pressure Pre-Set From 7.5 To 9 PSI
  • Fuel Pressure Regulator Required
  • Heavy Duty Construction For Continuous High rpm Operation
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Redesigned High Flow Valves Ensure Adequate Fuel Delivery
  • Inlet And Outlet Tapped For 3/8 in. NPT
See More

B & M – Transpak, 67-91 C6 Transmission (Part No.40228)

Transpak, 67-91 C6 Transmission

from

$152.99
Use the B&M Transpak to recalibrate your automatic transmission for optimum performance. With the Transpak you will be able to downshift into low at any speed, and keep it in low to any speed that you want.

Product Features:
  • Recalibrate Auto. Transmission
  • Optimum Performance
  • Select Your App. Mode
  • Improves Transmission Life
  • Trans. Removal Not Required
See More

Mr. Gasket – Dust Cap (Part No.2485)

Dust Cap

from

$12.09
If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:
  • Chrome Plated Steel
  • Set of 2 Caps
  • Easy Installation
  • 2 Per Set
See More

Edelbrock – NHRA Legal Ford FE 428 Cylinder Head (Part No.60058)

NHRA Legal Ford FE 428 Cylinder Head

from

$567.99


Product Features:
  • Out-of-the-Box Bolt-On Performance
  • Valves Promote Excellent Flow For Streetable Power
  • NHRA Accepted For Stock And Super Stock
  • Thicker Deck Surfaces than Other Brands
  • NHRA Accepted for Stock/Super Stock
See More

Edelbrock – Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1412)

Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$538.99
The Edelbrock 1412 Performer Series 800 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1412 Performer Series 800 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation. Dyno tests proved that the EPS 800 carb outperformed a Holley #3310 carb out-of-the-box by 26 ft-lbs. of torque and 22 hp on a small-block Chevy engine equipped with an Edelbrock Performer RPM power package

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
  • Can Easily Calibrate with Rods and Jets
See More

Accel – Module:Eliminator Replacement (Part No.2005)

Module:Eliminator Replacement

from

$91.99
Put an end to high maintenance point ignition systems by utilizing a specialized electronic circuitry and an infrared signal. Stabilizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.

Product Features:
  • Most Accurate Ignition Timing System
  • Improves Performance And Fuel Economy
  • Easy To Install With Simple Hand Tools
  • Reduced Maintenance
  • Eliminates Changing Points
See More

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Spectre – Oil Pan (Part No.5491)

Oil Pan

from

$165.99
This Spectre Performance oil pan was designed for Ford cars and 2WD trucks with 352, 360, 390, 406, 427, & 428 (except 428CJ and 428 SCJ) engines. This stock 4 quart capacity pan features a triple chrome-plated finish and durable steel construction. Precision engineered for optimum fit and function, this high quality OEM replacement part is easy to install.

Product Features:
  • Fits Ford cars and 2WD trucks (does not fit vans or 4WD trucks)
  • Fits 352-428 Ford engines (except the 428 CJ or 428 SCJ)
  • OEM replacement for easy installation
  • Triple chrome plated steel
See More

Upgrade your 1968 Ford Galaxie with Top-Quality Performance and Racing Products

When it comes to maintaining or upgrading your 1968 Ford Galaxie, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Performance and Racing Products are key to keeping your Galaxie functioning at its best. At Advance Auto Parts, we offer a wide selection of 79 Performance and Racing Products for the 1968 Ford Galaxie, designed to meet your needs without breaking the bank. From Performance Ignition Product replacements to Performance Exhaust Products upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Performance and Racing Products for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Performance and Racing Products for your 1968 Ford Galaxie at great prices. Our Performance and Racing Products inventory for this model ranges from just $12.09 to $1,138.99, with an average price of $334.18. Our 79 Performance and Racing Products in stock come from 15 trusted brands, so you’re sure to find the right part for your 1968 Ford Galaxie without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1968 Ford Galaxie, we stock popular OEM and aftermarket Performance and Racing Products from top names like Accel, Mr. Gasket, Edelbrock, and more. Accel Performance and Racing Products start at just $38.99 and boast an impressive 4 stars average rating from customers. Mr. Gasket and Edelbrock also bring quality to the table, with Performance and Racing Products available starting at $12.09, and at an average 4 stars rating. With 348 customer reviews and counting, our 1968 Ford Galaxie Performance and Racing Products have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Performance and Racing Product upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1968 Ford Galaxie is always ready to roll. We’re committed to providing you with everything you need to keep your Galaxie in top shape, all in one place. Start shopping confidently below for your 1968 Ford Galaxie!

Best-Selling Performance Ignition Products for 1968 Ford Galaxies

Enhance the driving experience in your Ford with 11 quality Performance Ignition Product components, starting at $30.49.

Mallory – Unilite Ignition Module (Part No.605)

Unilite Ignition Module

from

$85.29
Mallory’s UNILITE (R), and magnetic breaker less ignition modules are self contained module assemblies which have no moving parts to wear out. Using Mallory’s time tested breaker less ignition circuit, combined with modern surface mount thermal-clad construction, these ignition modules can drive both OEM and high performance ignition coils. For best results always use a Mallory PROMASTER coil or a Mallory chrome electronic ignition coil. These are also an excellent choice for triggering one of the Mallory HyFire series of electronic ignition controls. Hookup is as easy as a three wire connection.

Product Features:
  • Service Part
  • No Moving Parts To Wear Out
  • Self Contained Unit
  • Can Drive OEM
  • Can Drive High Performance Ignition Coils
See More

Accel – Contact And Condenser Kit (Part No.8203)

Contact And Condenser Kit

from

$79.99
Regain horsepower and economy for your street machine with new contact and condenser kit. Large tungsten contacts provide crisp coil firing and perform solidly up to 5,000 RPM. Condenser’s special winding protects from pitting of point contacts. Heavy duty 23 ounce points.

Product Features:
  • High Performance Points and Condenser
  • With Integral Conductor
See More

Mallory – Mallory Kit: Unil Conv: Delco: V8 (Part No.501)

Mallory Kit: Unil Conv: Delco: V8

from

$134.99
Put an end to high maintenance point ignition systems by installing a proven Mallory Unilite ignition conversion kit. Features at a glance, improves performance and fuel efficiency, easy to install with simple hand tools, reduced maintenance and is available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:
  • Easy Installation
  • Improved Fuel Economy
  • Reduced Maintenance
  • Accurate Timing
  • Improved Performance
  • Provides A Simple Conversion
  • No Moving Parts To Wear Out
See More

Accel – Super Stock Replacement Coil for Improved Performance, Starting, and Power (Part No.8140)

Super Stock Replacement Coil for Improved Performance, Starting, and Power

from

$42.49
Excellent high performance replacement for import and domestic vehicles with canister type oil filled coil. Re-engineered windings for even higher energy output resulting in quicker starting improved throttle response and more high RPM power. Designed to work with Points style and Breakerless electronic ignition systems. Heavy duty black Alkyd tower provides in flashover in protection to primary terminals. ACCEL Yellow can. 42000 volts effective up to 6500 RPM 1.4 ohms on the primary

Product Features:
  • 42000 Volts
  • Effective To 6500 RPM
  • Quicker Starting
  • Improved Throttle Response
  • Higher RPM Power
  • Can Finished In Yellow
See More

MSD Ignition – Blaster 2 Coil: High Performance Ignition Upgrade (Part No.8202)

Blaster 2 Coil: High Performance Ignition Upgrade

from

$49.99
If you are looking to upgrade your stock coil, or want to compliment the performance of your MSD blaster ignition, MSD 5, 6 or 7, the blaster coil line is the right choice. All of the blaster coils are designed for improved spark output. Special 100:1 windings are used to provide maximum build-up of voltage. These windings are held secure and kept cool in an oil filled metal canister. The tower assembly is molded of durable alkyd material due to its high dielectric characteristics while wide spaced brass primary terminals prevent the possibility of spark. There are several versions of the blaster coil available. All of them have the same internal specifications, but have different housings or components. Each blaster coil can be used with a stock ignition, blaster ignition, MSD 5, 6 or 7 ignition control. Most late model vehicles with electronic ignitions do not require a ballast resistor, check your ignition and manufacturers specifications to determine if a ballast is required in your application.

Product Features:
  • Improved output coil for electronic ignitions
  • Works w/Blaster Ignition Or MSD 5/6/7 Series
  • Ballast Resistor Required If Used w/Stock Points Ignition
  • Alkyd tower w/high dielectric properties lessens carbon tracking
See More

Accel – Supercoil (Part No.140001)

Supercoil

from

$105.99
Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:
  • Oil Filled For Better Cooling
  • Optimized Low Resistance
  • Silicon Magnetic Steel E-Core
  • Higher Energy/Voltage Outputs
  • Quicker Starts
  • Improved Idle Quality
  • Resists Shock And Vibration
  • Resists Corrosion
See More

Accel – Module:Eliminator Replacement (Part No.2005)

Module:Eliminator Replacement

from

$91.99
Put an end to high maintenance point ignition systems by utilizing a specialized electronic circuitry and an infrared signal. Stabilizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.

Product Features:
  • Most Accurate Ignition Timing System
  • Improves Performance And Fuel Economy
  • Easy To Install With Simple Hand Tools
  • Reduced Maintenance
  • Eliminates Changing Points
See More

Mallory – Distributor Wiring Harness (Part No.29349)

Distributor Wiring Harness

from

$30.49


Product Features:
  • Service Part
  • Makes Connections Quick And Easy
See More

Mallory – Promaster Classic Series; Ignition Coil (Part No.29440)

Promaster Classic Series; Ignition Coil

from

$186.99
Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:
  • Glass Filled Polyester Case
  • Longer Spark Duration
  • Increased Performance
  • No Energy Loss Due To Arcing
  • Includes Brass Contact Terminal
See More

Accel – Contact Set Hp 32 Oz (Part No.110228)

Contact Set Hp 32 Oz

from

$48.49
Heavy duty points sets are quipped with extra think contack arms to prevent flexing at high RPMS. Large radiused tungsten contants provide crisp circuit breaking for peak coil output. High strength phenolic rubbing blocks provide superior durability when used with heavy duty spring tension.

Product Features:
  • Extra Thick Contact Arms
  • Large Radius Tungsten Contacts
  • High Strength Phenolic Rubbing Blocks
  • Prevents Points Float
  • Moisture-Proof Buna-N Condenser
See More

Accel – CAP/ROTOR (Part No.8201)

CAP/ROTOR

from

$38.99
CAP/ROTOR

Most Popular 1968 Ford Galaxie Performance Exhaust Products

Customize your Ford with 3 Performance Exhaust Products products like Performance Exhaust Manifold Gaskets and Performance Exhaust Headers, all priced under $834.99.

FEL-PRO Performance – Exhaust Manifold Gasket Set (Part No.1442)

Exhaust Manifold Gasket Set

from

$33.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
  • Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
  • Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
  • Slotted bolt holes allow for easier header installation.
  • Not intended for use in emission controlled vehicles.
See More

Hooker Headers – Super Comp. Header (Part No.6130HKR)

Super Comp. Header

from

$834.99
Hooker has a complete line of engine swap headers, front frame mounts and transmission mounts for popular engine swaps. Available for Chevy, Chrysler and Ford small block and big block engines. Hooker swap headers and mounts are designed to provide an exact fit when used together. Hooker swap headers add the extra horsepower and torque the serious enthusiast demands. Hooker Headers are the best single improvement you can make.

Product Features:
  • Long Tube Lengths
  • Long Transition Collectors
  • Monstrous Low-Mid Range Torque
  • Keep Top End Horsepower
  • Provides Finest Fit
  • Most Durable Design Available
See More

Mr. Gasket – Engine Sealing (Part No.7555)

Engine Sealing

from

$38.99
Graphite impregnated facing and a steel expanded metal core. Superior tensile strength. Resists cracking and withstands intense heat. Resists deteriorating. Anti-stick properties and easy removal for disassembly.

Product Features:
  • Graphite-impregnated facing
  • Steel expanded metal core
  • Superior tensile strength
  • Resists cracking
  • Withstands intense heat
  • Resists deteriorating
  • Anti-stick properties
  • Easy removal for disassembly
See More

Top Picks for 1968 Ford Galaxie Performance Oil Filters

Upgrade Ford Galaxies with top-quality Performance Oil Filters parts, including 1 OEM and aftermarket selections for your 1968 model.

Mr. Gasket – Remote Oil Filter Kit (Part No.7682)

Remote Oil Filter Kit

from

$97.99
This kit relocates the oil filter for quick, clean and easy access and increased filtering. It is complete with precision die cast aluminum by-pass, filter brackets and all high pressure connectors.

Product Features:
  • Relocate oil filter to an easy access location
See More

In-Demand Performance Engines for 1968 Ford Galaxies

Select from 14 premium Performance Engines parts for your 1968 Ford Galaxie, with prices ranging from $26.99 to $597.99.

Mr. Gasket – High Performance 180 Degree Thermostat for Increased Flow (Part No.4364)

High Performance 180 Degree Thermostat for Increased Flow

from

$26.99
Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:
  • Opens At 180 Degrees
  • Designed to Resist Large Variations of Coolant Pressure at High RPM
  • Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
  • For High Performance Street, Drag Race, and Oval Track
  • Copper & Brass Construction – Resists Corrosion
  • High Flow
See More

Edelbrock – Performer 390 Intake Manifold for Ford FE, Satin Finish (Part No.2105)

Performer 390 Intake Manifold for Ford FE, Satin Finish

from

$597.99


Product Features:
  • For Idle to 5500 RPM Street-Driven Performance
  • Dual-Plane Low-Rise Intake w/180 deg. Firing Order
  • Patented Runner Design Ensures Broad Torque Curve
  • Excellent Throttle Response and Mid-Range Power
  • 50-State Street Legal if Correct Carburetor Used
See More

Spectre – Water Neck; Ford 390-428 (Part No.4736)

Water Neck; Ford 390-428

from

$47.99
Spectre’s Ford water neck fits Ford 390, 427 and 428 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:
  • Fits Ford 390, 427 and 428 engines
  • Includes bolts and gasket
  • Chrome plated
  • Easy to install
See More

Edelbrock – Sure Seat Valve Springs for Ford 429/460 V8 1969-1987 (Part No.5767)

Sure Seat Valve Springs for Ford 429/460 V8 1969-1987

from

$111.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:
  • For Use With Cast Iron Heads
  • Springs Made of Highest Quality Spring Wire
  • Springs Precision Wound To Close Tolerances
  • Use with Original Equipment Heads Only
See More

FEL-PRO Performance – Cylinder Head Gasket: Steel Core Composite, Without Head Bolts (Part No.1020)

Cylinder Head Gasket: Steel Core Composite, Without Head Bolts

from

$41.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro Performance head gaskets accommodate the high cylinder pressures and cylinder head movement associated with performance engines.
  • Inserted within a stainless steel armor surrounding each cylinder, wire ring design provides highly concentrated sealing around the combustion chamber.
  • Raises combustion sealing force to roughly three times that of standard head gaskets.
  • Steel wire rings for the greatest combustion seal strength.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – PERFORMANCE OIL PAN GASKET SET (Part No.1817)

PERFORMANCE OIL PAN GASKET SET

from

$27.49
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Felcoid/Plus gaskets have a fiber sheet core and a latex rubber coating to eliminate potential leakage paths. The core material resists crushing and splitting, while providing excellent blowout resistance.
  • With steel core to provide ultimate excellent blowout resistance.
  • Not intended for use in emission controlled vehicles.
See More

FEL-PRO Performance – Lower Intake Manifold Gasket Set: 5 Piece Set (Part No.1246)

Lower Intake Manifold Gasket Set: 5 Piece Set

from

$39.99
Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:
  • Fel-Pro performance intake manifold gaskets have been tested with virtually all aftermarket cylinder head and intake manifold combinations.
  • Performance intake manifold gaskets designed without a metal core, to allow engine builders to trim the gasket for exact fit on modified ports.
  • Standard and Low riser
  • Printoseal elastomeric sealing beads to provide extra sealing strength around the intake port.
  • Not intended for use in emission controlled vehicles.
See More

Edelbrock – NHRA Legal Ford FE 428 Cylinder Head (Part No.60058)

NHRA Legal Ford FE 428 Cylinder Head

from

$567.99


Product Features:
  • Out-of-the-Box Bolt-On Performance
  • Valves Promote Excellent Flow For Streetable Power
  • NHRA Accepted For Stock And Super Stock
  • Thicker Deck Surfaces than Other Brands
  • NHRA Accepted for Stock/Super Stock
See More

Edelbrock – #21053 Performer 390 Intake Manifold, Ford FE, 332-428, Black Finish (Part No.21053)

#21053 Performer 390 Intake Manifold, Ford FE, 332-428, Black Finish

from

$479.99
The Edelbrock Performer 390 #21053 intake manifold is designed for street 332-352-360-390-406-410-427-428 c.i.d. Ford V8’s with medium- or low-rise cylinder heads. Manifold not equipped with EGR; will not accept stock Motorcraft spread-bore carburetor or
See More

Edelbrock – Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79 (Part No.5792)

Sure Seat Valve Springs for Chrysler 383-400-413-440 V8 1969-79

from

$141.99
Product Features:
  • Non-Rotator Type
  • 1.550 in. Outer Diameter
  • .190 Wire Size
  • Single Coil Spring Type
  • Set of 16
See More

Edelbrock – Cylinder Head Gasket Set for Ford (Part No.7337)

Cylinder Head Gasket Set for Ford

from

$61.99
Product Features:
  • Cylinder Head Gasket Set
  • 1958-1976 390-428
See More

Edelbrock – Valve Cover Gasket Set for Ford (Part No.7568)

Valve Cover Gasket Set for Ford

from

$40.99
Product Features:
  • Valve Cover Gasket
See More

Mr. Gasket – Intake Gasket (Part No.202A)

Intake Gasket

from

$40.19
Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. They provide excellent sealing and durability. Can be trimmed if necessary for modified port applications. Complete with manifold end seals and distributor gasket (where applicable). For original equipment replacement, high performance street, drag race and oval track.

Product Features:
  • Manufactured from cellulose/nitrile composition gasket material
  • Provides excellent sealing and durability
  • Can be trimmed if necessary for modified port applications
  • Complete with manifold end seals and distributor gasket where applicable
  • For OE replacement, high performance street, drag race and oval track use
See More

Mr. Gasket – Head Gasket (Part No.1132G)

Head Gasket

from

$37.59
Mr. Gasket Embossed Steel Shim Cylinder Head Gaskets are for high performance street machines, drag racing and oval track racing. This is a very unique design that has a solid metal on metal fold at the combustion seal. This fold makes for a very stout seal that is almost the equivalent of a higher-end MLS (multi-layer steel) gasket with a gas stopper layer, but at a much lower cost. This gasket also has embossments around the coolant and oil passages and has a thick aluminum flake coating. All of these features result in a steel shim head gasket that handles extreme cylinder pressures very well. It’s probably the best steel shim head gasket you could ask for. Sold individually.

Product Features:
  • Embossed steel with aluminum flake coating
  • Solid metal over metal fold at the combustion seal
  • Embossed seals at coolant and oil passages
  • Approximately .020″ compressed thickness
  • For high performance street, drag race and oval track use.
See More

Most Sold 1968 Ford Galaxie Performance Fuel Systems

Explore our best-selling Ford parts for the 1968 Galaxie among 11 OEM and aftermarket options starting from $206.99.

Edelbrock – Performer 1411 Carburetor: 750 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1411)

Performer 1411 Carburetor: 750 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$494.99
The Edelbrock 1411 Performer Series 750 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characterist

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – CARBURETOR (Part No.14054)

CARBURETOR

from

$488.99
Product Features:
  • EnduraShine Finish
  • GM/AMC-Style Throttle Linkage
  • Can Add Electric Choke PN[1478]
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet (Part No.1406)

Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet

from

$428.99
The Edelbrock 1406 Performer Series 600 CFM electric choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1406 Performer Series 600 CFM electric choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Electric Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1405)

Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$394.99
The Edelbrock 1405 Performer Series 600 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1405 Performer Series 600 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation.

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1407)

Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$451.99
The Edelbrock 1407 Performer Series 750 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristic

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Holley – Street Carbs (Part No.0-80508S)

Street Carbs

from

$477.99
One of the most widely used Holley carbs of all times -the 0-80508S! Its dual feed fuel inlets assure you get all the fuel you need and its 750 CFM of airflow makes it the perfect performance upgrade carb. Its vacuum secondaries and electric choke make it super easy to use on a wide range of vehicles. Don’t trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60’s.

Product Features:
  • Vibratory Polished For Good Looks
See More

Edelbrock – CARBURETOR (Part No.14064)

CARBURETOR

from

$541.99
Product Features:
  • EnduraShine Finish
  • GM/AMC-Style Throttle Linkage
  • Electric Choke Installed from Factory
  • Easy Tuning with 2-Piece Design
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
See More

Edelbrock – Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet (Part No.1412)

Performer 1412 Carburetor: 800 CFM, 4 Barrel, Square Bore, Manual Choke Inlet

from

$538.99
The Edelbrock 1412 Performer Series 800 CFM manual choke carburetor is a precisely tuned, quality-built carburetor that can handle the rigors of daily driving while delivering consistent, reliable street performance from day to day. Several characteristics make the 1412 Performer Series 800 CFM manual choke carburetor an outstanding street performer. The first one is that metering rods are utilized to transition between circuits. The carburetor is unaffected by engine backfires, which means that there are no power valves to blow out, and the rods can be changed in seconds without carburetor removal or fuel draining. Secondly, the carburetor has the unique ability to “hold a tune”, so once it is tuned, the carburetor stay’s tuned. What this means to you is that compared to other carburetors, the performance remains consistent and the calibration stays unchanged. The lightweight all-aluminum body features a two-piece body that resists warping and is compatible with gasohol and blended fuels. The simple tub-type bowls and rear-pivot floats all contribute to a carburetor that’s reliable, user-friendly and is easily tunable for miles and miles of trouble-free operation. Dyno tests proved that the EPS 800 carb outperformed a Holley #3310 carb out-of-the-box by 26 ft-lbs. of torque and 22 hp on a small-block Chevy engine equipped with an Edelbrock Performer RPM power package

Product Features:
  • Edelbrock products offer improved performance and aesthetics for a broad array of vehicles and engines. ‘Proven performance’ is the philosophy by which Edelbrock was founded and it continues to this day with the highest standards for performance and quali
  • Manual Choke
  • 4 Barrel Count
  • Square Bore
  • Smooth Secondary Transition
  • Both Timed and Full Vacuum Ports
  • Includes PCV Outlet
  • Can Easily Calibrate with Rods and Jets
See More

Edelbrock – Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.18129)

Reman Thunder AVS Carb #18129 800 CFM With Manual Choke, Satin Finish (Non-EGR)

from

$413.99
Product Features:
  • Satin Finish
  • 4 Barrel
  • Aluminum Body Material
  • Manual Choke Type
  • 800 cfm Maximum Flow Rating
See More

Edelbrock – Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR) (Part No.9907)

Performer Carburetor #9907 750 CFM With Manual Choke, Satin Finish (Non-EGR)

from

$407.99
Product Features:
  • Satin Finish
  • 4 Barrel
  • Annular Booster Type
  • Manual Choke Type
  • 750 cfm Maximum Flow Rating
See More

Holley – Mechanical Fuel Pump (Part No.12-390-11)

Mechanical Fuel Pump

from

$206.99
Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:
  • High Output Fuel Flow
  • Flows 110 gph Free Flow
  • Shutoff Pressure Pre-Set From 6.5 To 8 PSI
  • Fuel Pressure Regulator Is Not Required
  • Heavy Duty Construction For Continuous High rpm Operation
  • Fuel Body Casting Can Be Rotated For Plumbing Situations
  • Inlet And Outlet Tapped For 3/8 in. NPT
  • Inlet/Outlet Tapped For 3/8 in. NPT
See More

Top-Rated Performance and Racing Products Brands For Your 1968 Ford Galaxie

Shop for the best-rated brands offering Performance and Racing Products and other products for your 1968 Ford Galaxies. Below you’ll find some of our best rated Performance and Racing Products from Accel, Mr. Gasket, and Edelbrock, and more. Performance and Racing Products from these brands that fit a 1968 Galaxie start at just $12.09 and are rated as high as 4 stars. OEM and aftermarket Performance and Racing Products don’t get more top quality, durable, and affordable than from the brands below.

Popular Accel 1968 Ford Galaxie Performance and Racing Products

When it comes to maintaining or upgrading your 1968 Ford Galaxie, using quality Performance and Racing Products is essential to ensure durability and a perfect fit. Accel ticks all of those boxes. We offer a wide selection of Accel Performance and Racing Products, specifically designed for the 1968 Ford Galaxie. With over 6 Accel brand Performance and Racing Products in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $38.99, with an average price of just $67.99. Plus, with over 55 customer reviews and an average rating of 4 stars, you can trust that our Accel Performance and Racing Products will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

Contact Set Hp 32 Oz
from
$48.49
This product is not rated

Contact Set Hp 32 Oz

“”

Supercoil
from
$105.99
This product is not rated

Supercoil

“”

Module:Eliminator Replacement
from
$91.99
This product is not rated

Module:Eliminator Replacement

“”

Popular Mr. Gasket 1968 Ford Galaxie Performance and Racing Products

Mr. Gasket auto parts is one of the highest quality Performance and Racing Product brands in the market. Any 1968 Ford Galaxie owner should feel confident when installing genuine Mr. Gasket parts in their vehicle. To ensure the best fit and performance for your 1968 Galaxie, Advance Auto Parts carries a full inventory of 9 Mr. Gasket Performance and Racing Products. Plus you will be keeping your Ford in peak condition while saving money because prices on these Mr. Gasket Performance and Racing Products range from $12.09 to $97.99, plus, with more than 20 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Performance and Racing Products below will deliver on both quality and value.

Thermocap Radiator Cap
from
$48.09
This product is not rated

Thermocap Radiator Cap

“”

Dust Cap
from
$12.09
This product is not rated

Dust Cap

“”

Remote Oil Filter Kit
from
$97.99
This product is not rated

Remote Oil Filter Kit

“”

FAQs for 1968 Ford Galaxie Performance and Racing Products

Which Performance and Racing Products are best-sellers for 1968 Ford Galaxies?

Out of 79 Performance and Racing Products that fit 1968 Ford Galaxies, the following parts are the top sellers:

What’s the price range for 1968 Ford Galaxie Performance and Racing Products?

Performance and Racing Product prices for the 1968 Ford Galaxie start at $12.09 and go up to $1,138.99 for the most premium parts.

What’s the average price of a Performance and Racing Product for a 1968 Ford Galaxie?

The average price for Performance and Racing Products for the 1968 Ford Galaxie is $334.18. Keep in mind the variety of part types within our Performance and Racing Product category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Performance and Racing Products for other Ford Galaxie model years?

Yes, we currently carry Performance and Racing Products for 15 model years of Ford Galaxies between 1959 and 1974. Performance and Racing Products are bought most frequently for the following model years: 1974, 1973, 1972, 1971, 1970, 1969, 1967, 1966, and 1965.

What are the cheapest Performance and Racing Products for my 1968 Ford Galaxie?

The cheapest 1968 Ford Galaxie Performance and Racing Products we carry in stock are:

What types of Performance and Racing Products do you sell for my 1968 Ford Galaxie?

Can I get help with 1968 Ford Galaxie Performance and Racing Product orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Performance and Racing Products and more.

What is your return policy for Ford Galaxie Performance and Racing Products?

Advance Auto Parts keeps returns simple. For new Ford Galaxie Performance and Racing Products and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.