1968 Ford F-250 Pickup Drivetrains

Name: Lock Right Locker
Brand: Powertrax
SKU: 2510-LR
Price: 475.99 USD

Below you will find various in-demand Ford Drivetrains, components and accessories for your 1968 F-250 Pickup. Advance Auto Parts has popular F-250 Pickup parts like Differentials, 4WD Components, Universal Joints and more. You’ll also find aftermarket and OEM Drivetrains for other F-250 Pickup model years including 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997 and more. Select a category of 1968 Ford F-250 Pickup Drivetrains below and start saving instantly.

Popular 1968 Ford F-250 Pickup Drivetrains Categories

Differential Oil

Axle Shaft Universal Joints

U-Joints

4WD Hubs

Rear Differential Cover Gaskets

Drive Shaft Center Supports

Differential Open Unit and Components

Differential Covers

Center Support Bearings

U-Joint Strap Kits

Differential Pinion Shaft Lock Bolts

Axle Shaft Bearing Assemblies

Differential Bearings

Differential Axle Shafts

Bearing Pullers

Drive Shaft Bearings

Axle Shaft Seals

Drive Shaft Slip Yoke Sleeves

Differential Pinion Pilot Bearings

Locking Hub Service Kits

Axle Spindle Seals

U-Joint Centering Yokes

Differential Cover Bolts

Axle Shaft Bearings

Transfer Case Output Shaft Seals

Differential Carriers

Differential Bearing Kits

Input Shaft Bearings

Front Differential Pinion Bearings

Differential Spider Gear Kits

Differential Rebuild Kits

Differential Carrier Shim Kits

Differential Pinion Seals

Axle Spindle Bearings

Differential Clutch Packs

Differential Ring and Pinions

U-Joint U-Bolt Kits

Differential End Yokes

Spindle Lock Nuts

Differential Lock Assemblies

Differential Air System Seal Housings

Spindle Nut Sockets

Rear Differential Pinion Bearings

Differential Spools

Differential Carrier Bearings

Front Differential Cover Gaskets

Rear Housing Cover Gaskets

Transfer Case Output Shaft Bearings

Differential Pinion Bearing Kits

Transfer Case Differential Bearings

Differential Seals

Complete Differentials

Differential Ring Gear Bolts

Bearing Race Drivers

Differential Carrier Bearing Shims

Input Shaft Seals

Spindle Retainers

Differential Crush Sleeves

Differential Side Bearing Spacers

Differential Pinion Shims

Differential Pinion Shaft Nuts

Differential Cross Pins

Mounting Adapter Seals

Differential Side Gear Thrust Washers

Differential Pinion Bearing Baffles

Differential Pinion Gear Thrust Washers

Differential Drive Pinion Oil Deflectors

Differential Carrier Bolts

Differential Pinion Gear Washers

Spindle Washers

Limited Slip Differential Assemblies

Differential Clutch Pack Clips

Axle Pinion Repair Sleeves

Universal Joint Snap Rings

Differential Lock Thrust Blocks

Essential Drivetrains for 1968 Ford F-250 Pickups

from

$475.99

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

from

$14.79

Product Features:

Brand may vary by location

from

$8.49

High-quality Differential Carrier Shim Kit

Product Features:

CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

from

$37.99

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$329.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits standard rotation Dana Spicer 44 front
Included are carrier bearings and races, pinion bearings and races, pinion seal, oil baffles and slingers , marking compound and brush.

from

$78.99

Seal housing for Ford 10.25″ & 10.5″, Zip locker, with o-rings.

Product Features:

Seal housing for Ford 10.25″ and 10.5″
Includes o-rings

from

$37.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$46.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$338.99

Yukon Performance steel spool for Dana 44 with 30 spline axles. fits 3.92 and up. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

Fits Chrysler Dana Spicer 44 with 30 spline axles
3.92 and up ratio only
Provides 100% traction to both wheels at all times
Not recommended for street driven vehicles

from

$38.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$11.99

Product Features:

Pinion gear thrust washer
Fits Dana Spicer 50

from

$304.99

Product Features:

Standard open carrier case
Fits Dana Spicer 44 with 19 spline axles
3.73 ratio and down only
Does not include spider gears

from

$16.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$939.99

Differential

from

$63.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles.
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid.
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$32.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$9.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$12.29

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models.
Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$36.99

Backed by superior materials and rigorous testing, MOOG Super Strength universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$215.99

Bearing race driver for Dana 60 front, Dana 70U rear, Chrysler 8.75″ with 42 housing, and ’88 and older GM 14T. No return.

Product Features:

Bearing race driver
Fits HM803110 race
All steel construction

from

$128.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 44 differential. This kit contains carrier bearings, races and shims.

Product Features:

Fits Dana Spicer 44
Includes carrier bearings and races and carrier shim kit

from

$5.99

Product Features:

Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
0.030″ thick

from

$9.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$9.99

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$7.99

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

Power Lok case bolt for Dana Spicer 60 and 70
7/16 x 14 thread
3.5″ long
9/16″ hex head

from

$193.99

Product Features:

DANA-44 R/P 3.73 STD

from

$3.29

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

Upgrade your 1968 Ford F-250 Pickup with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 1968 Ford F-250 Pickup, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Ford or enhancing its overall performance, Drivetrains are key to keeping your F-250 Pickup functioning at its best. At Advance Auto Parts, we offer a wide selection of 360 Drivetrains for the 1968 Ford F-250 Pickup, designed to meet your needs without breaking the bank. From Differential replacements to 4WD Components upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 1968 Ford F-250 Pickup at great prices. Our Drivetrains inventory for this model ranges from just $2.99 to $1,566.99, with an average price of $193.99. Our 360 Drivetrains in stock come from 18 trusted brands, so you’re sure to find the right part for your 1968 Ford F-250 Pickup without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 1968 Ford F-250 Pickup, we stock popular OEM and aftermarket Drivetrains from top names like Spicer, Moog, Driveworks, and more. Spicer Drivetrains start at just $28.99 and boast an impressive 5 stars average rating from customers. Moog and Driveworks also bring quality to the table, with Drivetrains available starting at $2.99, and at an average 4 stars rating. With 3,118 customer reviews and counting, our 1968 Ford F-250 Pickup Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 1968 Ford F-250 Pickup is always ready to roll. We’re committed to providing you with everything you need to keep your F-250 Pickup in top shape, all in one place. Start shopping confidently below for your 1968 Ford F-250 Pickup!

Best-Selling Differentials for 1968 Ford F-250 Pickups

Enhance the driving experience in your Ford with 245 quality Differential components, starting at $3.99.

show more show less

from

$8.49

Product Features:

Brand may vary by location

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$9.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$23.29

National« has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today┐s vehicles.

Product Features:

Design type: spring loaded; multi-lip
Temperature range: -20░F to 300░F / -29░C to 49░C
Resistance to EP lubricants
Low swell in hydrocarbon fluids
Delivers quality and reliable performance for every type of repair

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$10.49

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$8.29

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$143.99

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

D44 BRG & SEAL MASTER KIT-LATE 1968-UP

from

$27.99

Beck/Arnley parts meet foreign nameplate OE specifications for form, fit and function. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.

Product Features:

Matches OE form, fit and function
ABS magnet included if applicable
Made with high quality materials
Quality construction for durability
Application specific for this vehicle

from

$168.99

DANA-44 LATE TIMKEN MASTER KIT

from

$57.99

3 Qt. Penzoil 80W90 conventional gear Oil. W/ bottle of Posi additive.

Product Features:

Includes three quarts of conventional oil and one 4oz bottle of Yukon positraction additive

from

$11.99

Replacement ring gear bolt for Model 35, Dana 25, 27, 30 & 44. 3/8″ x 24.

Product Features:

Ring gear bolt for Dana Spicer 25, 27, 30, 44 and AMC Model 35
3/8″ x 24 thread

from

$9.99

5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.

Product Features:

Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
1/2″ head

from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$15.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$7.99

7/16″ TO 3/8″ ring gear bolt spacer sleeve.

Product Features:

Ring gear bolt sleeve
Adapts 7/16″ to 3/8″

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$47.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$15.99

Product Features:

Carrier shim kit for Dana Spicer 30 with 30 spline axles

from

$29.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$14.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$13.99

Product Features:

Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

from

$6.99

Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
3/4″ x 16 thread

from

$17.99

Replacement pinion seal for Dana 25, Dana 27, Dana 30, D36, Dana 44, & Dana 50 .Yukon Mighty seal.

Product Features:

Pinion seal
Fits Dana Spicer 25, 27, 30, 40 and 50

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$38.49

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$22.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$16.49

from

$19.99

Product Features:

Pinion preload shims for Dana Spicer 60 and 70U

from

$5.99

Product Features:

Side gear thrust washer for Ford 8″, Ford 9″ and AMC Model 20
0.030″ thick

from

$99.99

Redline Synthetic “Shock Proof” Oil. 3 Quarts.

Product Features:

Includes three quarts of Redline Shockproof oil

from

$18.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$203.99

Product Features:

Spider gear kit
Fit Dana Spicer 44 open differential with 30 spline axles
Includes two side gears, two pinion gears, cross pin shaft, cross pin bolt and spider gear thrust washers.

from

$137.99

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil

from

$67.99

0.080″ thick Chrome replacement cover for Dana 44.

Product Features:

Fits standard rotation Dana Spicer 44
Chrome

from

$69.99

Design type: spring loaded; multi-lip
Temperature range: -100°F to 450°F; -73°C to 232°C
Resistant to hydrocarbon/oxygenate blends and provides superior performance
Provides excellent dry running capabilities, low coefficient of friction and excellent resistance to chemicals
Delivers quality and reliable performance for every type of repair

from

$28.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$24.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$128.99

Fits Dana Spicer 44
Includes carrier bearings and races and carrier shim kit

from

$79.99

Seal housing for Dana 60, Zip locker, with o-rings.

Product Features:

Seal housing for Dana Spicer 60
Includes o-rings

from

$16.99

Product Features:

Cross pin shaft for Dana Spicer 44
Fits standard open differentials only

from

$9.99

Product Features:

Inner oil slinger for Dana Spicer 60

from

$9.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

Top Picks for 1968 Ford F-250 Pickup Universal Joints

Upgrade Ford F-250 Pickups with top-quality Universal Joints parts, including 50 OEM and aftermarket selections for your 1968 model.

show more show less

from

$28.99

When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.

from

$39.99

from

$25.99

Backed by superior materials and rigorous testing, MOOG Premium universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
GREASABLE DESIGN — Greasable u-joints allow for new grease to flush out contaminants and moisture
KEEPS DIRT OUT — Nitrile rubber grease seals use a compressed double lip design for effective protection against contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability
Cross forging shape and flash provide easier installation and high strength

from

$19.99

Backed by superior materials and rigorous testing, MOOG Heavy Duty universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for fleets, off-highway and commercial vehicles
STRONG AND DURABLE — Bearing cups are cold-formed, case-hardened and precision ground for strength and durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
GREASEABLE DESIGN — Drilled and tapped grease fitting holes for easy servicing and cross trunnions with large grease reservoirs with radial grease channels for grease distribution
INHIBITS PREMATURE WEAR — Cross trunnions ground to a 15-25 RMS finish for a smooth surface free of microscopic grooves that can cause premature wear
RELIABLE PERFORMANCE — Internal anti-drainback valve integrated into thrust washer controls lubrication flow and prevents dry startup
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on

from

$15.99

DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$32.99

Backed by superior materials and rigorous testing, MOOG Super Strength® universal joints deliver reliable performance you can count on. MOOG problem-solving innovations ensure fast, hassle-free installation.

Product Features:

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
CORROSION PROTECTION — Exclusive MICRO SHIELD coating protects against rust and corrosion
STRONG AND DURABLE — Cold-forged, case-hardened and precision-ground alloy steel crosses for durability
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates

from

$32.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$32.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$36.99

BUILT TO LAST — Rugged design specifically engineered for applications with higher torque and horsepower
COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
CORROSION PROTECTION — Exclusive MICRO SHIELDΓ┐ó coating protects against rust and corrosion
GREASABLE DESIGN — Bearing cups feature a radial design to allow 360 Degrees lubricant distribution to all bearing surfaces
KEEPS DIRT OUT — Abrasion-resistant nitrile seals provide ideal grease retention and protection from under-vehicle contaminants
RIGOROUS TESTING — Comprehensive testing throughout design and development processes by MOOG engineers for quality you can count on
STRONG AND DURABLE — Bearing cups are cold-forged, case-hardened and precision ground while steel cross is forged and carburized heat treated for strength and durability

from

$8.39

Universal Joint – Brute Force

from

$7.89

Universal Joint

from

$6.49

Universal Joint

from

$4.59

Universal Joint

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$47.99

from

$5.49

Universal Joint – Brute Force

from

$5.39

Universal Joint

from

$4.49

Universal Joint

from

$37.99

You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you’re getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.

from

$18.99

1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.

Product Features:

u-joint strap kit
Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
1310 and 1330 u-joint size
Includes two straps and four bolts

from

$73.99

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits standard rotation Dana Spicer 44 TJ Rubicon
8.50″ ring gear diameter
26 spline pinion
10 ring gear bolts
5.13 ratio

from

$44.99

Yukon 1310 U/Joint with zerk fitting on cross. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$59.99

Yukon 1310 to 1330 adapter U/Joint. The 1310 side has a 3.219″ span and 1.062″ caps. The 1330 side has a 3.625″ span and 1.062″ caps. Both sides are outside snap ring.

from

$34.99

1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.

Product Features:

u-joint u-bolt kit
Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
1310 u-joint size
Includes two u-bolts and four nuts

from

$16.99

1350 & 1410 U/joint U-bolts, 3/8″ X 1-11/16″, kit.

Product Features:

u-joint u-bolt kit
Fits 1350 and 1410 u-joint size
Includes two u-bolts and four nuts

from

$78.99

Yukon 1350 to 1410 conversion u/joint.

from

$44.99

SPICER U-JOINT

from

$109.99

Yukon 1310 to Mechanics 3R adapter U/Joint.

from

$63.99

Yukon 1350 Lifetime Series U/Joint. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring.

from

$61.99

Yukon 1330 Dual-size cap U/Joint. 3.625″ snap ring span. One set of caps is 1.125″ in diameter and the other is 1.062″. Outside snap ring.

from

$51.99

Yukon 1350 U/Joint with zerk fitting. 3.625″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$121.99

Yukon replacement yoke for Dana 30, 44, 50, and Dana 300 with 26 spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$53.99

1330 Yukon Lifetime U/Joint. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$51.99

Yukon 1330 U/Joint with zerk fitting. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring.

from

$57.99

1310 Yukon Lifetime U/joint. 1.718″ snap ring span, 1.062″ cap diameter. Inside snap ring.

from

$609.99

(2) 297X 4340 Chrome Moly Super-joints. Replacement joints for Dana 30, Dana 44 & GM 8.5″ front.

Product Features:

Fits Dana Spicer 30 and 44 and GM 8.5″ front
4340 Chromoly cross
Eliminated needle bearings results in larger trunion for added strength
Uses ultra high grade antiseize for lubrication
Not recommended for daily driven use
Two complete joints and eight full circle snap rings

from

$609.99

Yukon Chrome-Moly Super Joint kit for Dana 30, Dana 44 & GM 8.5″ front. Kit includes (2) 4340 Chrome Moly Super-joints, grease, and Gun.

Product Features:

Fits Dana Spicer 30 and 44 and GM 8.5″ front
4340 Chromoly cross
Eliminated needle bearings results in larger trunion for added strength
Uses ultra high grade antiseize for lubrication
Not recommended for daily driven use
Two complete joints, eight full circle snap rings, grease and grease gun

from

$412.99

Yukon Super Joint for GM 8.5″, Dana 30 & Dana 44. One single joint.

Product Features:

Fits Dana Spicer 30 and 44 and GM 8.5″ front
4340 Chromoly cross
Eliminated needle bearings results in larger trunion for added strength
Uses ultra high grade antiseize for lubrication
Not recommended for daily driven use
One complete joint and four full circle snap rings

from

$203.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1310 u-joint size
3.219″ snap ring span
1.062″ cap diameter
Outside snap ring design
U-bolt style

from

$111.99

Yukon 1350 to Mechanics 3R adaptor U/joint.

from

$84.99

Yukon 1410 Lifetime Series U/Joint. 4.188″ span ring span. 1.188″ cap diameter. Outside snap ring.

from

$61.99

Yukon 1410 U/Joint with zerk fitting. 4.188″ snap ring span, 1.118″ cap diameter. Outside snap ring.

from

$49.99

Universal Joint

from

$36.99

Universal Joint

from

$31.99

Strap kit for 1480 yoke in Dana 60, Dana 70, & Dana 80.

Product Features:

u-joint strap kit
Fits Dana Spicer 60, 70, 70U, 70HD and 80
1480 u-joint size
Includes two straps and four bolts

from

$19.99

(4) Full Circle snap rings, fit 297X U-joint with aftermarket axle.

Product Features:

Set of four full circle snap rings for Dana Spicer 30 and 44 and GM 8.5″ front

from

$17.99

U/joint strap kit, 10.25″, 9.5″, Dana 60, Dana 70, 1350 & 1410.

Product Features:

u-joint strap kit
Fits Ford 10.25″, GM 9.5″, Dana Spicer 60, 70, 70U and 70HD
1350 and 1410 u-joint size
Includes two straps and four bolts

In-Demand Drive Shafts and Axles for 1968 Ford F-250 Pickups

Select from 34 premium Drive Shafts and Axles parts for your 1968 Ford F-250 Pickup, with prices ranging from $7.99 to $883.99.

show more show less

from

$35.99

from

$34.49

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHEV 60-02; DODGE 57-02; FORD 55-07; GMC 63-02; INTL 57-02; KW 81-18; MACK 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 4 Lbs
BEARING ID / BORE: 1.5750 INCH / 40 MM
CENTERLINE: 2.48 INCH / 63 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
NOT PICTURED: TWO DUST SHIELDS

from

$15.99

The cross is hot forged for the higher torque and horsepower
The bearing cups are made by cold forging, having higher strength and better rigidity
Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
Snap rings are held to strict tolerances to ensure proper cup position and retention
Nitrile rubber seals to optimize grease retention and reduce contamination

from

$42.99

from

$73.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$44.99

from

$44.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$22.79

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to AUTOCAR 84-88; CHECKER 55-82; CHEV 60-12; DODGE 57-02; FORD 55-10; GMC 63-07; INTL 57-02; ISUZU 96-01; KW 81-18; MACK 80-90; MAZDA 87-94; MITS 87-09; OLDS 90-01; PLYM 80-83; PTRB 65-83; WHGM 88-95; WHIT 81-88;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1955-2018
Weight approx: 3 Lbs
BEARING ID / BORE: 1.3780 INCH / 35 MM
CENTERLINE: 2.28 INCH / 58 MM
MOUNT WIDTH: 6.62 INCH / 168 MM
STYLE: ROUND FRAME
COMPLETE MOUNT

from

$21.79

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$117.99

Product Features:

PINION YOKE
CAST:1310
U-BOLT STYLE

from

$37.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$111.99

Worn or damaged differential end yoke causing driveline vibrations? This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

Direct replacement – this differential end yoke matches the fit and construction of the original yoke.
Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts.
Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
Validated fit – this differential end yoke has been tested to confirm accurate fit

from

$55.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$15.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$49.49

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$7.99

Product Features:

Pinion yoke dust shield
Fits Dana Spicer 60 and 70

from

$883.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to one ton applications including Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings

from

$146.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1330 u-joint size
Outside snap ring design
3.625″ snap ring span
1.062″ cap diameter
Strap style

from

$125.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 44
26 spline
1330 u-joint size
3.625″ snap ring span
1.125″ cap diameter
Outside snap ring design
U-bolt style

from

$32.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$289.99

Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 30 and 44
26 spline
1350 u-joint size
Outside snap ring design
3.625″ snap ring span
1.188″ cap diameter
Strap style

from

$233.99

Yukon replacement yoke for Dana 44-HD, 60, and 70 with a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60 and 70
29 spline
1310 u-joint size
Outside snap ring design
3.219″ snap ring span
1.062″ cap diameter
Strap style

from

$219.99

Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1350 u-joint size
3.625″ snap ring span
1.188″ cap diameter
Outside snap ring design
U-bolt style

from

$187.99

Yukon replacement yoke for Dana 60 and 70 with a 1330 U/joint size. 3.625″ snap ring span, 1.0625″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects. This is a strap style yoke.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1330 u-joint size
3.625″ snap ring span
1.062″ cap diameter
Outside snap ring design
Strap style

from

$182.99

Replacement redi-sleeve yoke saver for Dana 25, Dana 27, Dana 30, Dana 44, Dana 50 .Yukon Mighty seal.

Product Features:

Pinion Redi-sleeve
Fits Dana Spicer 25, 27, 30, 4 and 50

from

$179.99

Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1350 u-joint size
3.625″ snap ring span
1.188″ cap diameter
Outside snap ring design
Strap style

from

$121.99

Yukon replacement axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. Axle bearing and seal kit for ’59 to ’75 Dana 44 and Ford 3/4 ton front axle. This kit includes Timken inner and outer bearings and races along with high quality seals. Unit is sold per side and is covered for one year against manufacturing defects. This axle bearing & seal kit services one side only.

Product Features:

Fits 1959-1975 Ford 3/4 ton
Includes axle bearings, races and seal
Services one side

from

$110.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Controlled heat treating process for lasting performance and extended bearing life
Industry leading coverage
Professional technicians know they can depend on National

from

$86.99

Drive Shaft End Yoke

from

$55.99

Center Support Bearing

from

$44.99

SPICER U-JOINT

from

$15.99

Product Features:

Brand may vary by location

from

$9.99

Yukon Gear & Install Kit package for Jeep TJ with Dana 30 front and Dana 44 rear, 4.88 ratio. This is a complete package that includes front & rear ring & pinion sets along with the most complete master overhaul kits on the market, giving you everything you need to re-gear the front & rear differential in one easy part number.

Product Features:

Fits Jeep TJ with Dana Spicer 30 front and Dana Spicer 44 rear
4.88 ratio
Includes front and rear ring & pinion sets and master overhaul kits

from

$7.99

Front wheel seal.Yukon Mighty seal.

Product Features:

Front wheel bearing seal
Fits 1955-1993 GM half ton front

Most Sold 1968 Ford F-250 Pickup Transfer Cases

Explore our best-selling Ford parts for the 1968 F-250 Pickup among 15 OEM and aftermarket options starting from $3.29.

show more show less

from

$5.99

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$37.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$16.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$14.29

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$3.29

Product Features:

Brand may vary by location

from

$19.29

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$11.49

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$6.49

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$19.29

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$24.99

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$28.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National

from

$15.49

BEARING

from

$10.99

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$7.99

Product Features:

Brand may vary by location

from

$6.29

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

Top-Rated Drivetrains Brands For Your 1968 Ford F-250 Pickup

Shop for the best-rated brands offering Drivetrains and other products for your 1968 Ford F-250 Pickups. Below you’ll find some of our best rated Drivetrains from Spicer, Moog, and Driveworks, and more. Drivetrains from these brands that fit a 1968 F-250 Pickup start at just $2.99 and are rated as high as 5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Spicer 1968 Ford F-250 Pickup Drivetrains

When it comes to maintaining or upgrading your 1968 Ford F-250 Pickup, using quality Drivetrains is essential to ensure durability and a perfect fit. Spicer ticks all of those boxes. We offer a wide selection of Spicer Drivetrains, specifically designed for the 1968 Ford F-250 Pickup. With over 17 Spicer brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $28.99, with an average price of just $74.46. Plus, with over 33 customer reviews and an average rating of 5 stars, you can trust that our Spicer Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

from
$241.99

This product is not rated

Differentil End Yoke

“”

from
$37.99

This product is not rated

Universal Joint

“”

from
$44.99

This product is not rated

SPICER U-JOINT

“”

Popular Moog 1968 Ford F-250 Pickup Drivetrains

Moog auto parts is one of the highest quality Drivetrain brands in the market. Any 1968 Ford F-250 Pickup owner should feel confident when installing genuine Moog parts in their vehicle. To ensure the best fit and performance for your 1968 F-250 Pickup, Advance Auto Parts carries a full inventory of 6 Moog Drivetrains. Plus you will be keeping your Ford in peak condition while saving money because prices on these Moog Drivetrains range from $19.99 to $36.99, plus, with more than 355 customer reviews and an impressive 4 stars average rating, you can be confident the Fram Drivetrains below will deliver on both quality and value.

from
$19.99

(82)

Greaseable Premium Universal Joint

“Great product”

from
$32.99

(30)

Non-Greaseable Super Strength Universal Joint

“Working great.”

from
$25.99

(143)

Greaseable Premium Universal Joint

“Good product”

FAQs for 1968 Ford F-250 Pickup Drivetrains

Which Drivetrains are best-sellers for 1968 Ford F-250 Pickups?

Out of 360 Drivetrains that fit 1968 Ford F-250 Pickups, the following parts are the top sellers:

Universal Joint (10265714) – $15.99
Universal Joint (10265720) – $15.99
Bearings (5051460) – $16.99

What’s the price range for 1968 Ford F-250 Pickup Drivetrains?

Drivetrain prices for the 1968 Ford F-250 Pickup start at $2.99 and go up to $1,566.99 for the most premium parts.

What’s the average price of a Drivetrain for a 1968 Ford F-250 Pickup?

The average price for Drivetrains for the 1968 Ford F-250 Pickup is $193.99. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Ford F-250 Pickup model years?

Yes, we currently carry Drivetrains for 41 model years of Ford F-250 Pickups between 1953 and 1997. Drivetrains are bought most frequently for the following model years: 1997, 1996, 1995, 1994, 1993, 1992, 1991, 1990, and 1989.

What are the cheapest Drivetrains for my 1968 Ford F-250 Pickup?

The cheapest 1968 Ford F-250 Pickup Drivetrains we carry in stock are:

Oil Seal (5441072) – $2.99
Oil Seal (10659691) – $3.29
Dana 44 JK / 60 / 70U Pinion Nut Washer Replacement (11643194) – $3.99
Dana 25 / 27 / 30 / 36 / 44 / 53 Pinion Nut Washer Replacement (11642796) – $3.99
Universal Joint (5270197) – $4.49

What are the top-rated Drivetrains that fit the 1968 Ford F-250 Pickup?

Out of 3,118 reviews by customers, our 1968 Ford F-250 Pickup Drivetrains have an average customer rating of . These are some of the highest-rated Drivetrain types for the 1968 Ford F-250 Pickup and their top-rated products:

Universal Joints
- Universal Joint (10854997) – $39.99
- Universal Joint (10855076) – $28.99
- Greaseable Premium Universal Joint (10086900) – $19.99
4WD Components
- Universal Joint (10854997) – $39.99
- Universal Joint (10855076) – $28.99
- Greaseable Premium Universal Joint (10086900) – $19.99

What types of Drivetrains do you sell for my 1968 Ford F-250 Pickup?

As of 2/5/25, these are some of the most in-demand types of Drivetrains for a 1968 Ford F-250 Pickup:

Can I get help with 1968 Ford F-250 Pickup Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Ford Drivetrains and more.

What is your return policy for Ford F-250 Pickup Drivetrains?

Advance Auto Parts keeps returns simple. For new Ford F-250 Pickup Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.

1968 Ford F-250 Pickup Drivetrains

Powertrax – Lock Right Locker (Part No.2510-LR)

Driveworks – Tapered Roller Bearing (Part No.S-3920)

Motive Gear – Differential Carrier Shim Kit (Part No.1101)

National – Shaft Repair Sleeve (Part No.99199)

Yukon Gear – Bearing Install Kit For Dana 44 Differential (Straight Axle) (Part No.11020)

Yukon Gear – Seal Housing For Ford 10.25" & 10.5", Zip Locker, With O-Rings (Part No.34040)

National – Bearings (Part No.307-L)

National – Bearings (Part No.308)

Yukon Gear – Steel Spool For Dana 44 With 30 Spline Axles, 3.92 & Up (Part No.32041)

National – Shaft Repair Sleeve (Part No.99155)

Yukon Gear – Replacement Pinion Gear Thrust Washer For Spicer 50 (Part No.33439)

Yukon Gear – Replacement Standard Open Carrier Case For Dana 44, 19 Spline, 3.73 & Down (Part No.20019)

Motive Gear – Differential Pinion Seal (Part No.9316)

Yukon Gear – Differential (Part No.26040)

Dorman – Rear Differential Cover (Part No.697-704)

National – Bearings (Part No.88107-BVV)

Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)

Driveworks – Oil Seal (Part No.S-5131)

Dorman – Help – Plastic Insert Spindle Nut 2 In.-16 Hex Size 2-9/16 In. (Part No.81035)

MOOG Driveline Products – Greaseable Super Strength Universal Joint (Part No.270)

Yukon Gear – Bearing Race Driver (Part No.56011)

Yukon Gear – Dana 44 Carrier Installation Kit Replacement (Part No.57003)

Yukon Gear – Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement (Part No.33283)

National – Bearings (Part No.02820)

National – Multi Purpose Seal (Part No.472394)

Yukon Gear – Dana 60 & Dana 70 Power Lok Case Bolt (Part No.33236)

Motive Gear – Differential Ring and Pinion (Part No.D44-373)

Pro-King – Differential Cover Gasket (Part No.764A303)

Driveworks – Tapered Roller Bearing (Part No.S-362-A)

Felpro – Axle Housing Cover Gasket (Part No.RDS 6629)

National – Bearings (Part No.15245)

National – Multi Purpose Seal (Part No.5778)

National – Bearings (Part No.387A)

Driveworks – Oil Seal (Part No.S-5778)

Felpro – DIFFERENTIAL GASKET (Part No.RDS 6095-1)

Motive Gear – Differential Master Bearing Kit – Koyo (Part No.RA28LRMK)

Beck/Arnley – Wheel Bearing (Part No.051-3936)

Motive Gear – Differential Master Bearing Kit – Timken (Part No.RA28LRMKT)

Yukon Gear – 3 Qt – 80W90 Conventional Gear Oil With Posi Additive (Part No.15003)

Yukon Gear – Replacement Ring Gear Bolt For Model 35, Dana 25, 27, 30 & 44 – 3/8" X 24 (Part No.33038)

Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)

Yukon Gear – Dana 60, Dana 70 & Dana 80 Cover Bolt (Part No.33235)

National – Bearings (Part No.HM88610)

Yukon Gear – Replacement Ring Gear Bolt For Dana 60, 70, 70U & 70HD, 1/2" X 18 (Part No.33037)

Yukon Gear – Chrysler 9.25" And Dana 44 / 60 Tracloc Clutch Guide Replacement (Part No.33249)

Yukon Gear – 7/16" To 3/8" Ring Gear Bolt Spacer Sleeve. (Part No.33056)

Yukon Gear – Redi-Sleeve Yoke Saver For 8.75" C, 9.25" C, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD (Part No.30228)

National – Bearings (Part No.HM88542)

National – Bearings (Part No.HM803146)

Yukon Gear – Replacement Carrier Shim Kit For Dana Spicer 44, 30 Spline Axles (Part No.55010)

National – Bearings (Part No.02872)

National – Bearings (Part No.HM88510)

Yukon Gear – Replacement Carrier Shim Kit For Dana 60, 70, 70HD, 70U & 80 (Part No.55011)

Yukon Gear – Replacement Pinion Nut For Dana 25, 27, 30, 36, 44, 53 & GM 7.75" (Part No.33143)

Yukon Gear – Dana 25 / 27 / 30 / 36 / 44 / 50 Pinion Seal Replacement (Part No.30128)

Yukon Gear – Redline Synthetic "Shock Proof" Oil With Positraction Additive – 4 Quarts (Part No.15005)

National – Shaft Repair Sleeve (Part No.99155)

National – Bearings (Part No.HM803110)

Motive Gear – Differential Pinion Seal (Part No.9316)

Yukon Gear – Replacement Pinion Preload Shims For Dana 60, Dana 61 & Dana 70-U (Part No.55015)

Yukon Gear – Dana 44, Ford 8" / 9", And Model 20 Side Gear Thrust Washer Replacement (Part No.33283)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 3 Quarts (Part No.15000)

National – Bearings (Part No.382S)

USA Standard Gear – Open Spider Gear Set For Dana Spicer 44, 30 Spline (Part No.39006)

Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)

Yukon Gear – Replacement Chrome Cover For Dana 44 (Part No.32004)

National – Multi Purpose Seal (Part No.5778V)

National – Bearings (Part No.31594)

Motive Gear – Differential Pinion Seal (Part No.6808N)

Yukon Gear – Dana 44 Carrier Installation Kit Replacement (Part No.57003)

Yukon Gear – Seal Housing For Dana 60, Zip Locker, With O-Rings (Part No.34039)

Yukon Gear – Replacement Cross Pin Shaft For Dana 44, Standard Open (Part No.33318)

Yukon Gear – Replacement Inner Slinger For Dana 60 (Part No.33014)

National – Bearings (Part No.02820)

Yukon Gear – Dana 50 Dana 60 Dana 70 & Dana 80 Roll Pin, 0.225" Dia, For X/P Shaft, 1.87" Lng (Part No.33327)

Yukon Gear – Replacement Outer Oil Slinger For Dana 60, 70, 70U & 70HD (Part No.33019)

Milemarker – MileMarker Street Master; Manual Hub (Part No.302)

Milemarker – MileMarker Supreme; Manual Hub (Part No.104)

Milemarker – MileMarker Supreme; Manual Hub (Part No.449S/S)