1968 Dodge Polara Differentials

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• USA Standard Gear heavy-duty cross pin shaft
• Fits Chrylser 8.25″ with 27 and 29 spline axles
• Works with Spartan Locker or standard open spider gears

These Yukon replacement diff covers take your rig a step beyond the boring factory look. They are the stock OE design finished in chrome.

Product Features:

• Fits Chrysler 9.25″ rear
• Chrome

Ring/Pinion Sets

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Chrysler 8.75″ ’42’ case housing with 25520 carrier races
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Redline Heavy Shockproof Gear Oil is formulated to provide lasting protection. This kit includes four quarts of oil and a bottle of Yukon Limited Slip Friction modifier that reduces noise and chatter in clutch driven positraction units and limited slip differentials.

Product Features:

• Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Crush sleeve for AMC Model 35, Chrysler 7.25″ and 8.25″, Ford 8″ and GM 7.75″
• 0.495″ tall

Product Features:

• MINI INSTALL KIT CHRYSLER 8.75 8 3/4″ LATE

Product Features:

• C9.25 OPEN INTERNAL KIT, 1984-UP

High-quality Differential Component Shim

Product Features:

• SHIM KIT FITS-8.25-F7.5-AMC20-GM0

We develop and produce high-quality roller bearings, spherical bearings, and plain bearings worldwide for a wide range of applications.

Product Features:

• High-precision and High-quality components used in all KITs
• Coverage of classic and new high-tech solutions for the best system coverage

Product Features:

• FULL SPOOL DANA 60 35 SPLINE 4.10 & DOWN

Yukon Gear & Axle dropouts are heavy duty. They feature upgraded nodular iron construction and a larger-than-OEM design to provide unrivaled strength and reliability in racing and off-road applications.

Product Features:

• Fits Chrysler 8.75″
• 89
• Nodular iron for added strength

Worn or damaged differential end yoke causing driveline Vibrations- This direct replacement end yoke matches the original equipment part for a trustworthy repair and reliable performance.

Product Features:

• Direct replacement – this differential end yoke matches the fit and construction of the original yoke
• Excellent value – this replacement end yoke offers original equipment quality at a fraction of the price of dealer parts
• Quality materials – this end yoke is machined from cast iron for strength and is precision machined for reliability
• Validated fit – this differential end yoke has been tested to confirm accurate fit

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side adjuster lock bolt
• Fits Chrysler 7.25″, 8.25″, 8.75″ and 9.25″

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Side adjuster
• Fits Chrysler 7.25″ and 8.25″

Side gear thrust washer kit for 8.25″ Chrysler, 27 spline only.

Product Features:

• Side gear thrust washer kit
• Fits Chrysler 8.25″ with 27 spline axles

Yukon axle kit for Chrysler 8.75″. This kit contains two green bearings, ten axle studs and two cut to length axles that fit A, B & E body cars, 5 x 4.5″ pattern.

Product Features:

• 30 spline
• 5 x 4.5″ bolt pattern
• Cut to length design fits 28″-32″ applications
• Axle kit
• Includes two axles, two green bearings and 10 axle studs

Yukon Mighty Seals use the latest design and manufacturing technologies to produce a precision fit that seals tight and lasts for years to come.

Product Features:

• Redi-Sleeve yoke saver
• Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

Yukon Gear and Axle offers a full line of top quality differential tools to save time and money.

Product Features:

• For Dana 60, Dana 70, Chrysler 8.75″ w 42 case housing, and GM 10.25″ differentials
• For accurate installation of bearing races
• Fits HM803110 race

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion gear thrust washer
• Fits Chrysler 8.25″

For vehicles that are driven daily, the Power Trax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Power Trax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Power Trax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Power Trax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds.

Product Features:

• The Power Trax Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Power Trax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.
• Power Trax lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.
• Power Trax offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.
• Power Trax ia an Extreme Traction System

Yukon Pinion Installation Kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings and races can be reused. This kit features Timken bearings and races along with high-quality seals and small parts. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your gear set.

Product Features:

• Fits Chrysler 8.75″ ’41’ case
• Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• MASTER KIT CHRYSLER 1.75″ PINION

For vehicles that are driven daily, the Powertrax No-Slip Traction System is the latest design in quiet traction-adding differential technology. It combines the automatic street-friendly smooth operation of a limited-slip differential with the traction performance of a locking differential. The Powertrax No-Slip locker easily installs in to your differential carrier using basic tools and without affecting your ring and pinion settings. Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!

Yukon Gear & Axle manufactures a full line of top quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers and much, much more. For all your differential small parts needs, look no further than Yukon.

Product Features:

• Pinion nut
• Fits Chrysler 8.75″ with 10 spline pinion

Yukon Gear & Axle manufactures a full line of top-quality small parts to complete any job including ring gear bolts, crush sleeves, pinion nuts and washers, axle studs, thrust washers, and other general maintenance items. You can count on Yukon to fulfill all your differential small parts needs.

Product Features:

• Clutch kit
• Fits Dana Spicer 44 and Chrysler 8.75″ Power Lok
• Aggressive design