1964 Ford F-250 Pickup Differentials

Yukon Power Lok positraction replacement internals for Dana 44 and Chysler 8.75″ with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 44 and Chrysler 8.75″ Powr Lok positraction
• Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

Product Features:

• Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
• For Trac Loc positraction applications only

Product Features:

• Clutch kit
• Fits Dana Spicer 44 and Chrysler 8.75″ Powr Lok
• Aggressive design

aFe Power’s new rear differential cover brings performance engineering to the protection of your axles differential. This differential cover is constructed out of durable die cast aluminum with reinforced ribs and wrinkle black powder coating for maximum strength and styling. This cover comes with all necessary hardware and includes an O-ring for a leak free seal. This cover has about a 5 quart lube capacity at the factory line; factory cover holds about 4 quarts. Built-in internal and external fins transfer heat from the fluid to the outside air for maximum cooling. This system incorporates a large magnetic drain and fill plug that captures loose particles for maximum rear-end protection. Pre-installed large oil level sight glass with calibration plug set to the factory fluid level to eliminate overfilling.

Product Features:

• External Fins Transfer Heat To Atmosphere
• Internal Fins Absorb Heat From Lubricating Fluid
• Magnetic Fill Plug
• Magnetic Drain Plug

Product Features:

• Pinion preload shims for Dana Spicer 60 and 70U

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Dana Spicer 60 front
• Included are a pinion seal, axle seals, crush sleeve , complete shim kit, marking compound and brush.

Product Features:

• Pinion nut washer for Chrysler 7.25″, 8.25″, 8.75″ with 29 spline pinion, Jeep JK rear, Dana Spicer 60, 70, 70U and 70HD and 2007-2010 Ford 10.5″

55P Chevy Passenger Drop Out gasket.

Product Features:

• Side gear thrust washer
• Fits Ford 10.25″

Replacement crush sleeve for Dana 44 & Dana 50 APROX 2.650″ long.

Product Features:

• Crush sleeve for Dana Spicer 44 and 50
• 2.650″ tall

High-quality Differential Carrier Shim Kit

Product Features:

• CARRIER SHIMS 12 BOLT GM CAR & TRUCK ALSO GM8.6″ 99-ON

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

• Fits Dana Spicer 44 with 30 spline axles
• 3.92 ratio and up only
• 4-spring, clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U

Product Features:

• O-ring for seal housing
• Fits Dana Spicer 44 and Toyota 8″ and V6

Product Features:

• Drive flange cap
• Fits Dana 44
• Yukon engraved

Differential

Product Features:

• DANA-44 R/P 5.38 STD MG

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 60 differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Dana Spicer 60
• Includes carrier bearings and races and carrier shim kit

Product Features:

• Carrier shim kit for Dana Spicer 60, 70, 70HD, 70U and 80

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands of many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON*, DEXRON*-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

• Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Product Features:

• Inner oil slinger for Dana Spicer 60

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.

Product Features:

• Roll pin for Dana Spicer 30 and Dana Spicer 44
• 0.235″ diameter

10.25″ Ford ” OEM” pinion seal.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Ford 10.25″

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

7.5″, 8″, 8.8″, 9″, 10.25″ Ford REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Redi-Sleeve yoke saver
• Fits Ford 7.5″, 8.8″, 9″ and 10.25″

Product Features:

• Brand may vary by location