1990 Ford F-250 Pickup Differentials

7/16″ TO 3/8″ ring gear bolt spacer sleeve.

Product Features:

• Ring gear bolt sleeve
• Adapts 7/16″ to 3/8″

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects. This unit fits full floating applications only.

Product Features:

• Fits Ford 10.25″ and 10.5″
• Clutch style positraction
• Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
• Fully rebuildable
• Assembled in the USA

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

• 35 spline
• 8 x 3.96″ bolt pattern
• Cut to length design fits 40″-43.5″ applications
• Fits Dana Spicer 60, 70 and 80

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• DANA-60 TIMKEN – UP TO ’98 FORD

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t

Product Features:

• Powr Lok button kit
• Fits Dana Spicer 30, 44 and Chrysler 8.75″

Product Features:

• Seal housing for Dana Spicer 44
• Includes o-rings

Product Features:

• Pinion gear thrust washer
• Fits Dana Spicer 50

Product Features:

• Oil baffle for Dana Spicer 30, Dana Spicer 44 IFS, Dana Spicer 50, AMC Model 35 IFS

Replacement front axle inner seal redi-sleeve for Dana 44 & 8.5″ GM.Yukon Mighty seal.

Product Features:

• Axle Redi-sleeve
• Fits Dana Spicer 44

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
• Required replacement – when servicing the differential
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Right hand inner 4340 Chrome Moly replacement axle shaft for Dana 44, ’75-’79 Ford F250, uses 5-760X u/joint. 34.75″ long with 30 splines. Yukon 4340 Chrome-Moly axles provide up to 50% increased strength over stock axles for use in extreme performance applications with large tires and high horsepower. Yukon’s 4340 axles are manufactured using the latest technologies and the highest quality materials to ensure high strength and long life. Limited Lifetime warranty covers manufacturing defects and axle breakage for as long as you own the vehicle. This warranty is not transferable to another party. “No Questions Asked” replacement for first warranty return, however Yukon reserves the right to either replace axle or refund original purchase price after the first warranty claim. Yukon (through Randy’s ring & pinion) makes final determination on warranty considerations.

Product Features:

• Fits 1978-1979 Ford F250 front with Dana Spicer 44
• 4340 Chromoly
• Right hand side inner
• 30 spline
• 34.75″ from end of splines to center of u-joint bore

Product Features:

• Outer oil slinger for Dana Spicer 25, 27, 30, 44 and 50

Yukon Power Lok positraction replacement internals for Dana 44 and Chysler 8.75″ with 30 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fit Dana Spicer 44 and Chrysler 8.75″ Powr Lok positraction
• Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

Product Features:

• MINI-INSTLTN KIT-DANA 70

Standard Open case for Ford 9.75″. This is a bare case and does not come with any internal components. This part carries a one year warranty against manufacturing defects.

Product Features:

• Standard open carrier case
• Fits Ford 9.75″
• Does not include spider gears

Yukon long yoke for ’93 and newer Ford 10.25″ with a 1330 U/joint size. 3.625″ snap ring span, 1.125″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits 1993 and up Ford 10.25″
• 31 spline
• 1310 u-joint size
• Outside snap ring design
• 3.625″ snap ring span
• 1.125″ cap diameter
• U-bolt style

Product Features:

• Carrier shims for Dana Spicer 60 and 70U

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for Dana 60 differential. This kit contains carrier bearings, races and shims.

Product Features:

• Fits Dana Spicer 60
• Includes carrier bearings and races and carrier shim kit

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits HM88510 race
• All steel construction

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 1992 and down Dana Spicer 44 IFS
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

• PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION – Crowned raceways for even load distribution
• OE-STYLE DESIGN – Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

• Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
• 0.225″ diameter
• 1.870″ long

Product Features:

• DANA-44 R/P 5.38 STD MG

Spartan spring & pin kit, fits larger designs.

Product Features:

• Fits Dana Spicer 60
• Replacement alignment pin and spring kit

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

• Cross pin shaft
• Fits Dana Spicer 60 and 70
• Powr Lok positraction only

10.25″ Ford carrier Supershims.

Product Features:

• Super carrier shim kit for Ford 10.25″ and 10.5″
• Interlocking design makes installation much easier

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits Dana Spicer 60 rear
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.