1962 Ford F-100 Pickup Differentials

Product Features:

• Carrier shim kit for Dana Spicer 30 with 30 spline axles

9″ Ford gasket.

Product Features:

• Dropout gasket
• Fits Ford 9″

9″ large solid pinion preload spacer & shim kit for 35 spline pinion.

Product Features:

• Crush sleeve eliminator kit for Ford 9″ with 35 spline pinion

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

• Cover bolt for Dana Spicer 60, 70 and 80
• 3/8″

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• KIT BRG & SEAL FORD 8.8″

Spartan spring & pin kit, fits smaller designs.

Product Features:

• Replacement spring and pin kit for Spartan Locker
• Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
• Includes 4 springs and 4 alignment pins

Yukon replacement positraction internals for Dana 60 and 70 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

• Clutch kit
• Fit Dana Spicer 60 Powr Lok positraction with 35 spline axles
• Smooth design
• Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

Product Features:

• FRD 10BLT 9.0 R/P 5.57AX MGP

STAR washers, 3.062″ Yukon Ford 9″ Drop Out new design ONLY.

Product Features:

• Star washer
• Fits Ford 9″
• 3.062″ designs only

Axle shaft damaged or bearings worn out? This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

• Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
• Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
• Durable construction – designed to rigorous standards and tested to ensure performance
• Trustworthy solution – backed by team of engineers and quality control specialists in the United States

Yukon standard open spider gear kit for and 9″ Ford with 28 spline axles and 4-pinion design. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

• Spider gear kit
• Fits Ford 8″ and 9″ open differential with 28 spline axles
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

The Yukon Grizzly Locker is the ultimate in locking differentials for street, off-road, & drag racing. Grizzly Lockers provide 100% power to both tires, while still allowing for disengagement while negotiating turns. The Yukon Grizzly locker is a mechanical locking differential. It features a forged case and 8620 internals for maximum strength. It’s patented design reduces common locker failures. All units assembled in the USA! All Grizzly Lockers are backed by the best warranty in the business! Yukon covers the replacement unit and covers any collaterally damaged parts and associated labor, up to $2,000! This is a narrow case locker. If you have a wide housing, please order two DS 42563 with your locker. This locker is ABS compatible.

Product Features:

• Fits Dana Spicer 60 with 40 spline axles
• 4.56 and up ratio only
• Patented internal design reduces common locker failures
• 8620 internals for added strength
• Assembled in the USA

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Design type: spring loaded; single-lip
• Temperature range: -40 Deg. F to 225 Deg. F / -40 Deg. C to 107 Deg. C
• Good low temperature capability
• Low swell in hydrocarbon fluids
• Delivers quality and reliable performance for every type of repair

Trac Loc clutch guide for 9″ Ford.

Product Features:

• Clutch guide
• Fits Ford 8″ and 9″

Set-up carrier bearing (2 bearings, no races) 25590. No return.

Product Features:

• Set up bearing kit
• Fits Dana Spicer 44
• Easily slips on and off carrier journals to allow for easier carrier shim adjustment

Pump up kit, Zip Locker.

Product Features:

• Tire pump up kit
• Includes hose, fittings, couplers and teflon tape

Pinion support bolt for 8″ and 9″ Ford.

Product Features:

• Pinion support bolt for Ford 8″ and 9″
• 3/8″ x 24 thread
• 1.0″ long

Product Features:

• KIT SHIM

Product Features:

• Oil baffle for Dana Spicer 60 and Dana Spicer 70U

9″ Yukon 3.062″ aluminum case, HD dropout housing with forged caps. The Yukon aluminum dropouts feature a adjuster lock which is offset 90 degrees, offering an uninterrupted bearing cap for higher strenth. Made from A356-T6 aluminum and featuring a through-bolt desgin, this dropout is built for high horsepower & tall tires.Rated up to 1000HP!

Product Features:

• Fits Ford 9″
• 3.062″ carrier race diameter
• A356-T6 aluminum
• Thru-bolt design added strength

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits Ford 9″ with LM102910 carrier race
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pilot bearing, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

Yukon Performance steel spool for Dana 60 with 30 spline axles. fits 4.10 and down. Yukon performance spools are made from the highest quality materials to ensure high strength and long life in performance applications. Spools provide 100% power to both tires at all times and are a lower cost alternative to lockers. Spools are not recommended for street driven vehicles. Yukon Performance spools come with a one year warranty against manufacturing defects.

Product Features:

• Fits Chrysler Dana Spicer 60 with 30 spline axles
• 4.10 and down ratio only
• Provides 100% traction to both wheels at all times
• Not recommended for street driven vehicles

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using premium-grade steel for outstanding durability and performance
• SMOOTH ROTATION: Crowned raceways and rollers for even load distribution
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Product Features:

• Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

Replacement pinion nut washer for Dana 25, 27, 30, 36, 44 & 53.

Product Features:

• Pinion nut washer for Dana Spicer 25, 27, 30, 44 and 50

Yukon replacement yoke for Dana 30, 44, and 50 with fine spline and a 1310 U/joint size. 3.219″ snap ring span, 1.062″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Dana Spicer 44
• 26 spline
• 1310 u-joint size
• 3.219″ snap ring span
• 1.062″ cap diameter
• Outside snap ring design
• Strap style

Product Features:

• DANA-44 R/P 5.38 STD MG