from

$59.99

Product Features:

Non-Rotator Type
1.394 in. Outer Diameter
1.010 in. Inner Diameter
1.010 in. Coil Blind
Set of 16

from

$128.99

These ACCEL carbon and graphite core wire sets virtually eliminate RFI noise, while providing maximum conductivity for ultimate performance in any race or street application. Double silicon insulation eliminates leakage and misfire.

Product Features:

Heavy Duty 8.8mm Oversized Silicone Jacket
500 Ohms/ft. Of Resistance
550 Degree Double Silicone Construction
Fiberglass Braid
Carbon/Graphite Core
Magnetic Suppression
Fiberglass/Kevlar Core
500 Ohms Resistance

from

$14.29

Chrome plated breather cap is ideal for race car vacuum balance systems, as well as original equipment applications with positive crankcase ventilation (PCV).

Product Features:

Features 1″ O.D. neck and a 5/8″ O.D. breather tube
Breather has Metal/Foam Baffle inside and includes Grommet
Fits all aftermarket valve covers with a 1.22″ Dia. opening

from

$105.99

Engineered for faster rise time, longer spark duration and increased performance. Unique design with premium grade wire, special low resistance, high turns ratio windings. Produces higher spark energy with breakerless electronic ignition systems. For points application the supplied 0.85 ohm ballast resistor must be used in conjunction with the vehicle original ballast resistor, if so equipped. Oversized molded case with integral cooling fins and high capacity oil filled construction provide high thermal conductivity ensuring cool operation and long life. Extra tall tan Alkyd tower and integral voltage dam eliminate “flashover” to primary terminals. Comes complete with mounting hardware and 0.85 ohm ballast resistor. Effective up to 6,500 RPM.

Product Features:

Oil Filled For Better Cooling
Optimized Low Resistance
Silicon Magnetic Steel E-Core
Higher Energy/Voltage Outputs
Quicker Starts
Improved Idle Quality
Resists Shock And Vibration
Resists Corrosion

from

$17.79

Fuel pump mounting pad cover is used to cover the hole in the block when the mechanical fuel pump is removed to use an electric pump.

Product Features:

Mechanical Fuel Pump Mounting Pad Cover For Chrysler V-8ft.S

from

$32.59

Product Features:

Prevents Air Inclusion
Direct Replacement
For OE Bleeders
One Person Bleeds Safely
Without The Mess
No Chance Of Air Bubbles

from

$26.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$16.99

FRAM Racing® filters are designed with a heavy-gauge tapping plate and an extra-thick* steel can that is able to withstand the high pressure flexing caused by demanding driving conditions. A spiral-shaped center tube provides protection against collapse, and tough steel end caps add even more durability. A screen-over 22psi filter bypass valve provides additional protection against larger contaminants.**

Product Features:

Proven protection for up to 10,000 miles
Engineered for use with synthetic or conventional motor oils
Filter media is a blend of fiber and resin that captures 95% of the dirt particles
The perfect balance of dirt-trapping efficiency and dirt-holding capacity

from

$18.99

Oil Pan Bolt Kit

from

$30.49

Product Features:

Service Part
Makes Connections Quick And Easy

from

$12.09

If you have custom steel or mag wheels that are not designed without a provision for a center cap, you’re probably looking at an ugly stock dust cap in the center of your front wheels. This chrome dust cap fixes that problem, and is a direct replacement for stock cap 1.790 inches in diameter. Two per set.

Product Features:

Chrome Plated Steel
Set of 2 Caps
Easy Installation
2 Per Set

from

$32.09

These special Grade 8 intake manifold bolts feature a 12-point smaller-than-standard head and flange, and include special extra thick flat washers for optimum clamping pressures. They’re ideal for use where space is minimal, typical on larger runner race manifolds. These bolts and washers are bright zinc plated for protection and good looks.

Product Features:

Features 12-point Smaller-than-standard Bolt Head
Thick Flat Washers Distribute Optimum Clamp Load
Ideal Use Where Space Is Minimal On Race Manifolds
Bolts And Washers Zinc Plated For Protection
Zinc Plated For Protection

from

$154.99

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1962-up TF727 transmissions and all internally balanced Chrysler, Dodge and Plymouth V8 engines with 6-bolt crankshaft flange. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.00 or 11.125 inch converter mounting locations and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953.

Product Features:

NHRA/IHRA Legal For All Classes
Includes SFI Certification Sticker
Ideal For Street Applications
To Extreme Duty Racing
To High RPM Use

from

$60.29

Copperseal exhaust gaskets are unique gaskets made from .043 inch solid copper. They feature an embossed O-ring design for a leak proof seal. They won’t shrink, deteriorate or blowout. Header bolts stay tight. Ideal for motor homes and towing.

Product Features:

Will Not Shrink/Deteriorate
Creates A Tight Leak Proof Seal
Helps Lower Under hood Temps
Seals Irregular Surfaces
Seals Slightly Damaged Surface
Ideal For Tow Vehicles
Ideal For Motor Homes

from

$31.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
Slotted bolt holes allow for easier header installation.
Not intended for use in emission controlled vehicles.

from

$79.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$91.99

Put an end to high maintenance point ignition systems by utilizing a specialized electronic circuitry and an infrared signal. Stabilizes ignition timing from 1 to 10,000 RPM. Improves performance and fuel efficiency, easy to install with hand tools, reduces maintenance. It is built with the latest thermal clad based surface mount construction for maximum dependability and long life.

Product Features:

Most Accurate Ignition Timing System
Improves Performance And Fuel Economy
Easy To Install With Simple Hand Tools
Reduced Maintenance
Eliminates Changing Points

from

$27.49

These grade 5 hex head bolts are black coated plated for protection and appearance. Hardened flat washers provide uniform torque and prevent galling on aluminum manifolds.

Product Features:

Assures Accurate Torque App
Prevents Galling Manifold
Grade 5 Material
Black Oxide Coasted

from

$397.99

Product Features:

For Idle to 5500 RPM Street-Driven Performance
Dual-Plane Low-Rise Intake w/180 Deg Firing Order
Patented Runner Design Ensures Broad Torque Curve
Excellent Throttle Response and Mid-Range Power
50-State Street Legal if Correct Carburetor Used

from

$23.79

Spectre’s Chrysler water neck fits 1964 and later Chrysler V8 engines. This water neck has been designed around the OEM specifications and has a chrome plated finish for a lasting look that fits great. This water neck includes bolts.

Product Features:

Fits 1964 and later Chrysler V8 engines
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$113.99

Designed to reduce wheel shimmy and end vibration caused by larger tires, the Rancho® steering stabilizer kit cuts down on steering arm fatigue to improve handling. The kit includes one Rancho RS5000® steering stabilizer and installation brackets.

Product Features:

COMPATIBILITY — Designed for a variety of trucks and SUVs from Chevrolet®, GMC®, Ford®, Dodge®, Jeep®, Plymouth® and International®
IMPROVED HANDLING AND PERFORMANCE — Reduces wheel shimmy, bump steer and vibration which helps minimize on- or off-road driver fatigue
ACCOMMODATES LARGER TIRES — Engineered for vehicles with oversized wheels and tires.
ENGINEERED TO LAST — Features protective boot to shield shock rod and oil seal and 0.25-in. high-strength, low-alloy steel bracket construction for long life
EASY TO INSTALL — Includes one Rancho RS5000® steering stabilizer and brackets that bolt directly to factory steering linkage with included mounting hardware, no modifications needed
RESISTS CORROSION — Durable black powder-coated and/or zinc-plated brackets resist rust and corrosion
PRECISION DESIGN — Brackets are CNC cut and bent to exact specifications for a perfect fit

from

$251.99

Designed to reduce wheel shimmy and end vibration caused by larger tires, the Rancho® steering stabilizer kit cuts down on steering arm fatigue to improve handling. The kit includes two Rancho RS5000® steering stabilizers and installation brackets.

Product Features:

COMPATIBILITY — Designed for a variety of trucks and SUVs from Chevrolet®, GMC®, Ford®, Dodge®, Jeep® and Plymouth®
IMPROVED HANDLING AND PERFORMANCE — Reduces wheel shimmy, bump steer and vibration which helps minimize on- or off-road driver fatigue
ACCOMMODATES LARGER TIRES — Engineered for vehicles with oversized wheels and tires.
ENGINEERED TO LAST — Features protective boot to shield shock rod and oil seal and 0.25-in. high-strength, low-alloy steel bracket construction for long life
EASY TO INSTALL — Includes one Rancho RS5000® steering stabilizer and brackets that bolt directly to factory steering linkage with included mounting hardware, no modifications needed
RESISTS CORROSION — Durable black powder-coated and/or zinc-plated brackets resist rust and corrosion
PRECISION DESIGN — Brackets are CNC cut and bent to exact specifications for a perfect fit

from

$379.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.