Volvo 242 Drivetrains
Top Volvo 242 Drivetrains Categories
We carry over 123 Drivetrains in inventory for the Volvo 242. If you’re looking for aftermarket Drivetrains for your Volvo 242, check out all these categories:
Essential Volvo 242 Drivetrains
Yukon Gear – 1310 & 1330 U/Joint Strap, Dana 30, Dana 44, Model 35, & 9.25" With Bolts (Part No.41195)
from
$18.99
1310 & 1330 U/joint strap, Dana 30, Dana 44, Model 35, & 9.25″ w/bolts.
Product Features:
See More
Product Features:
- u-joint strap kit
- Fits Dana Spicer 30 and 44, AMC Model 35 and Chrysler 9.25″
- 1310 and 1330 u-joint size
- Includes two straps and four bolts
Yukon Gear – Seal Housing For Dana 30, Model 35 Zip Locker (Part No.34012)
from
$78.99
Product Features:
See More
- Seal housing for Dana Spicer 30 and AMC Model 35
- Includes o-rings
Yukon Gear – Replacement Standard Open Spider Gear Kit For Dana 30 With 27 Spline Axles (Part No.16073)
from
$155.99
Yukon replacement standard open spider gear kit for Dana 30 with 27 spline axles and with or without quick disconnect. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Spider gear kit
- Fit Dana Spicer 30 open differential with 27 spline axles
- Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
Yukon Gear – Redline Synthetic "Shock Proof" Oil – 4 Quarts (Part No.15004)
from
$137.99
Redline Synthetic “Shock Proof” Oil. 4 Quarts.
Product Features:
See More
Product Features:
- Includes four quarts of Redline Shockproof oil
Yukon Gear – Pinion Install Kit For Dana 30 Rear Differential (Part No.13017)
from
$279.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.
Product Features:
See More
Product Features:
- Fits Dana Spicer 30 rear
- Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.
National – Shaft Repair Sleeve (Part No.99139)
from
$39.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
Yukon Gear – Set Up Bearing (Part No.56036)
from
$172.99
Set-up carrier bearing kit (2 bearings, no races) LM501349. No return.
Product Features:
See More
Product Features:
- Set up bearing kit
- Fits Dana Spicer 30
- Easily slips on and off carrier journals to allow for easier carrier shim adjustment
Yukon Gear – Dana 25, 27, 30, 44, Model 20 And Model 35, GM 7.5", 8.2", 8.5", 12P, 12T, C9.25 Rear Cover Bolt (Part No.33286)
from
$9.99
5/16″-18 cover bolt, Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, Chrysler 9.25 rear, GM 7.5″, 7.625″, 8.2″, 8.5″, 12 bolt passenger car and truck.
Product Features:
See More
Product Features:
- Cover bolt for Dana Spicer 25, 27, 30 and 44, AMC Model 20 and Model 35, GM 7.5″, 7.625″, 8.2″, 8.5″ and 12 bolt passenger car and truck.
- 1/2″ head
Driveworks – Transfer Case Output Shaft Seal (Part No.S-1172)
Yukon Gear – Powr Lok Button Kit For Dana 30, Dana 44 & Chrysler 8.75" (Part No.33536)
from
$67.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Powr Lok button kit
- Fits Dana Spicer 30, 44 and Chrysler 8.75″
Yukon Gear – Replacement Chrome Cover For Dana 30 Standard Rotation (Part No.32003)
Yukon Gear – Dana 30 & Dana 44 Power Lok Bolt, Left Hand, & 8.75" Chrysler & 55P (Part No.33234)
from
$26.99
Dana 30 & Dana 44 Power Lok bolt, left hand, & 8.75″ Chrysler & 55P.
Product Features:
See More
Product Features:
- Power Lok case bolt for Dana Spicer 30, Dana Spicer 44, Chrysler 8.75″ and 1955-1964 GM passenger car
- Left hand thread
Yukon Gear – High Performance Ring & Pinion Replacement Gear Set For Dana 30 In A 3.54 Ratio (Part No.24018)
from
$439.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.
Product Features:
See More
Product Features:
- Fits standard rotation Dana Spicer 30 without crush sleeve
- 7.20″ ring gear diameter
- 26 spline pinion
- 10 ring gear bolts
- 3.54 ratio
Yukon Gear – Dana 30 / 44 Roll Pin Replacement (Part No.33312)
from
$12.99
Dana 30 & Dana 44 roll PIN, 0.235″ DIA, for cross pin shaft.
Product Features:
See More
Product Features:
- Roll pin for Dana Spicer 30 and Dana Spicer 44
- 0.235″ diameter
USA Standard Gear – Open Spider Gear Set For Dana Spicer 30, 27 Spline (Part No.39005)
from
$151.99
Product Features:
See More
- Spider gear kit
- Fits Dana Spicer 30 27 spline open differential
- Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.
National – Bearing Race (Part No.HM88610)
from
$15.49
Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Driveworks – Taper Bearing Cone (Part No.S-LM-501349)
from
$10.99
Value-priced bearing meets all cataloged application requirements.
Product Features:
See More
Product Features:
- Brand may vary by location
USA Standard Gear – Spartan Locker for Dana 30 Differential with 27 Spline Axles, Includes Heavy-duty Cross Pin Shaft (Part No.17000)
from
$639.99
The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect. Does not fit Std. JK Carrier. Use YC D706008
Product Features:
See More
Product Features:
- Fits Dana Spicer 30 with 27 spline axles
- Made from 9310 steel for added strength
- Replaces the spiders in a standard carrier case
Yukon Gear – Dana 44, 8.2", 12P, 12T, Vet, And Model 20 U-Bolts (Part No.41198)
from
$34.99
1310 U-bolts, 5/16″ x 1-3/8″ Dana 30, Dana 44, 8.2″, 12P, 12T, VET, Model 20.
Product Features:
See More
Product Features:
- u-joint u-bolt kit
- Fits AMC Model 20, Dana Spicer 30 and 44, GM 8.2″, 12 bolt passenger car and truck and 1963-1979 Corvette
- 1310 u-joint size
- Includes two u-bolts and four nuts
Yukon Gear – Replacement Pinion Nut For Dana 25, 27, 30, 36, 44, 53 & GM 7.75" (Part No.33143)
from
$6.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses t
Product Features:
See More
Product Features:
- Pinion nut for Dana Spicer 25, 27, 30, 44, 50 and GM 7.75″
- 3/4″ x 16 thread
National – Shaft Repair Sleeve (Part No.99155)
from
$38.99
National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.
Product Features:
See More
Product Features:
- Designed to repair damaged, grooved or worn shafts
- Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
- Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
- Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
- Easy to install with removable flange and installation tool
- Installation tool reduces sleeve distortion and allows for installation without removal from the shaft
National – Multi-Purpose Bearing (Part No.306)
from
$44.99
Product Features:
See More
- BUILT TO LAST: Advanced heat treatment process for strength
- PREMIUM MATERIALS: Precision manufactured using premium-grade steel for lasting performance and extended bearing life
- RELIABLE PERFORMANCE: Element size and quantity are engineered to meet or exceed the load rating of OE bearings
- COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Spicer – Universal Joint (Part No.5-1310X)
from
$38.99
You expect a lot from your vehicle, and Spicer Life Series (SPL) universal joints deliver. SPL universal joints consistently outperform competitors, so you can hit the road or trail with confidence. Check out the difference that SPL universal joints can make in your vehicle, and make sure you are getting the longer life, increased bearing capacity and lower maintenance costs that Spicer Life Series (SPL) can provide.
See More
Yukon Gear – Replacement Yoke For Dana 30, 44, And 50 With 26 Spline And A 1350 U/Joint Size (Part No.41021)
from
$289.99
Yukon replacement yoke for Dana 30, 44, and 50 with 26 spline and a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses straps. All Yukon yokes come with a one year warranty against manufacturing defects.
Product Features:
See More
Product Features:
- Fits Dana Spicer 30 and 44
- 26 spline
- 1350 u-joint size
- Outside snap ring design
- 3.625″ snap ring span
- 1.188″ cap diameter
- Strap style
National – Tapered Roller Bearing Cone (Part No.HM88649)
from
$19.99
Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.
Product Features:
See More
Product Features:
- PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
- SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
- OE-STYLE DESIGN – Engineered to meet OE specifications
- COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
- RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on
Volvo 242 Drivetrains Categories
Helping You Find the Right Drivetrains for Your Volvo 242
You love your 242. So we’ve made it easier than ever to help you find Volvo 242 Drivetrains in our online catalog. Our inventory holds 123 aftermarket and OEM Drivetrains for your Volvo 242, ranging from $3.99 to $1,566.99.
We offer parts from 10 brands trusted to make quality Drivetrains for your Volvo 242. Before you buy, take some time to read through customer reviews. We currently have 11,666 reviews of Volvo 242 Drivetrains from previous customers. Some of the top rated parts include Greaseable Super Strength Universal Joint with 4.6 stars and Multi-Purpose Bearing with 4.8 stars.
Find your 242 Drivetrains here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Volvo 242 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Drivetrains Brands for Your Volvo 242
Our inventory holds Drivetrains for your Volvo 242 from 10 trusted brands. You’ll find OEM and aftermarket parts from brands like Valvoline, Moog, and Driveworks, all of which can keep that Volvo happy.
We have Spicer parts available for your Volvo 242 in categories like Universal Joints and Drive Shafts and Axles. Some of the top-rated Spicer parts in these categories are:
Top-Rated Valvoline Drivetrains
Leading Valvoline Drivetrains
We carry Valvoline brand parts for your Volvo 242 across several catalog categories, including Differentials. Some of our most reviewed Valvoline parts include:
FAQs for Volvo 242 Drivetrains
What are the most purchased Drivetrains for the Volvo 242?
Out of 123 Drivetrains for the Volvo 242, the most popular in our inventory are:
What are the top-rated Volvo 242 Drivetrains?
Top-rated Drivetrains for your Volvo 242 based on customer reviews/ratings are:
from
$41.49
(37)
Greaseable Super Strength Universal Joint
“grease fitting I like location dont like needle design to grease should be regular design fitting”
from
$17.99
(7)
Multi-Purpose Bearing
“Comparable with the Timkens I removed. NATIONAL bearings have lasted decades in many of my other machines.”
