from

$5.99

3/8″ cover bolt, Dana 60, Dana 70 & Dana 80.

Product Features:

Cover bolt for Dana Spicer 60, 70 and 80
3/8″

from

$6.99

Product Features:

Oil baffle for Dana Spicer 60 and Dana Spicer 70U

from

$8.99

Positraction clutch guide.

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44, Dana Spicer 50, Ford 8.8″, GM 12 bolt passenger car, GM 8.2″, 8.5″ and 8.6″, 1963-1979 Corvette and Nissan Titan
Compatible with Dura Grip positractions only

from

$8.99

Ring gear bolt for Chrysler 7.25″, 8″ IFS, 8.25″, 8.75″ & GM 7.2″ IFS front. 3/8″ x 24.

Product Features:

Ring gear bolt for Chrysler 7.25″, 8.0″ IFS and 8.75″
3/8″ x 24 thread
.866″ long

from

$379.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Chrysler 8.75″ ’42’ case
Included are pinion bearings and races, pinion seal, pinion nut, complete pinion shim kit, and marking compound with brush.

from

$204.99

Yukon replacement yoke for Dana 60 and 70 with a 1350 U/joint size. 3.625″ snap ring span, 1.188″ cap diameter. Outside snap ring. This yoke uses u-bolts. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

Fits Dana Spicer 60, 70, 70U and 70HD
29 spline
1350 u-joint size
3.625″ snap ring span
1.188″ cap diameter
Outside snap ring design
U-bolt style

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM88610 race
All steel construction

from

$103.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits Chrysler 8.75″ ’89’ case
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$269.99

Dana 60 & Dana 61 TracLoc clutch set.

Product Features:

Clutch kit
Fit Dana Spicer 60 Trac Loc positraction

from

$6.49

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$26.99

Spartan spring & pin kit, fits smaller designs.

Product Features:

Replacement spring and pin kit for Spartan Locker
Fits Dana 30, Dana 44, AMC Model 20, AMC Model 35, and Toyota designs
Includes 4 springs and 4 alignment pins

from

$788.99

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

Fits Chrysler 8.25″ with 27 spline axles
Made from 9310 steel for added strength
Replaces the spiders in a standard carrier case

from

$78.99

Yukon Carrier installation kits are great, low cost kit for carrier changes such as Positraction or locker upgrades. Carrier installation kit for ’76 & up Chrysler 8.25″ rear.

Product Features:

Fits 1976 and up Chrysler 8.25″
Includes carrier bearings and races

from

$62.99

Differential side bearing screw adjuster for 9.25″ Chrysler.

Product Features:

Side adjuster for Chrysler 9.25″ rear

from

$252.99

Yukon 1541H alloy cut to fit rear axle for Chrysler 8.75″ measuring 28″-32″ with 30 splines and 5×4.5 bolt pattern. for use with A, C & E-Body. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. Must use Green bearing.

Product Features:

Fits Chrysler 8.75″
30 spline
Cut to length design fits 28″-32″ applcations
5 x 4.5″ bolt pattern

from

$37.99

Replacement redi-sleeve yoke saver for 8.75″ c, 9.25″ c, Dana 60, Dana 61, Dana 70, Dana 70U, Dana 70HD .Yukon Mighty seal.

Product Features:

Redi-Sleeve yoke saver
Fits Chrysler 8.75″ and 9.25″ rear, Dana Spicer 60, 70, 70U and 70HD

from

$56.99

Side gear thrust washer for 7.25″ Chrysler.

Product Features:

Side gear thrust washer kit
Fits Chrysler 7.25″

from

$43.99

Product Features:

Pinion nut
Fits Chrysler 7.25″, 8.0″, 8.25″, 9.25″ and 8.75″ with 29 spline pinion

from

$9.99

Product Features:

Inner oil slinger for Dana Spicer 60

from

$148.99

Redline Synthetic “Shock Proof” Oil with positraction Additive. 4 Quarts.

Product Features:

Includes four quarts of Redline Shockproof oil and one 4oz bottle of Yukon positraction additive

from

$73.99

Standard Open notched cross pin shaft for 9.25″ Chrysler.

Product Features:

Cross pin shaft
Fits Chrysler 9.25″
Standard open carrier only
Notched

from

$362.99

Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses Timken bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:

Fits Chrysler 8.75″ ’42’ case housing with 25520 carrier races
Included are carrier bearings and races, pinion bearings and races, pinion seal, marking compound and brush.

from

$14.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National