Nissan 300ZX Fluids

We’ve squeezed innovation into every ounce of Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil, the ultimate gear protection in hypoid rear differentials and non-synchronized manual transmissions. Our unique new flexible pouch makes getting into the tightest places to lubricate gears easier than ever and with less waste. The superior detergent package-based formulation contains fully synthetic basestocks and special additives that help protect parts from rust and corrosion while providing exceptional high and low temperature protection and excellent thermal stability, especially in demanding driving situations such as towing and off-roading. It contains an extreme pressure additive for better load carrying capacity, wear resistance additives that assist in protecting gear teeth, a limited slip additive for optimal clutch pack performance, and an anti-foaming agent for better lubrication and service life. Valvoline FlexFill SAE 75W-90 Full Synthetic Gear Oil is recommended for use in axle applications requiring factory-fill or drain-and-fill levels for limited slip performance.

Product Features:

• FLEXIBLE POUCH FOR EASIER USE WITH LESS WASTE in tight, hard to reach undercarriage situations.
• EXCEPTIONAL HIGH AND LOW TEMPERATURE PROTECTION ranging from -30F to 300F degrees for dependable coverage year-round
• REDUCES CHATTERING AND PROTECTS GEAR TEETH from oxidation, rust, and wear
• MEETS THE DEMANDS OF CONVENTIONAL AND LIMITED SLIP REAR DIFFERENTIALS where API GL-5 is specified, as well as non-synchronized manual transmissions that require API GL-4 or MT-1 fluid
• MEETS OR EXCEEDS PERFORMANCE REQUIREMENTS for Mack GO-H and GO-J; API GL-5 and API MT-1; MIL-PRF-2105E; and SAE J2360

Prestone DOT 3 Motor Vehicle Brake delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Prestone® DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system. This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula*
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system
• Synthetic, Extended Fluid Life Formula

Prestone MAX DOT 3 Motor Vehicle Brake Fluid is our highest grade formula, maximizing performance vs. DOT standard. Prestone MAX is our best brake fluid at protecting against overheating and brake fade. With 100,000 mile fluid life, our longest life fluid has 2X more miles between replacement than regular Prestone DOT 3. Prestone MAX has superior performance in severe braking conditions when compared to regular Prestone DOT 3, which means even more piece of mind about the braking system. This synthetic fluid starts with our highest dry boiling point giving our best protection against performance decline due to water absorption. Prestone MAX DOT 3 is safe to use in all DOT 3 braking systems, ABS, disc or drum, and can mix with any DOT 3 fluid. Mixing Prestone MAX with other fluids will lower the performance rating for miles and boil points, for best results replace completely with Prestone MAX DOT 3. It is recommended to only use the DOT fluid specified for your car. Using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 100,000 Mile Fluid Life
• Prevent Overheating and Brake Fade with Our Highest Grade Formula. Prevents corrosion of all metals within the braking system.
• Superior Protection in Extreme Braking Conditions
• Synthetic, Long Life Formula – 2X Longer than regular Prestone DOT 3

Prestone DOT 3 Motor Vehicle Brake Fluid delivers enhanced performance vs. DOT standards, benefitting all vehicles calling for DOT 3. This synthetic fluid starts with a higher dry boiling point than the DOT minimum standard to protect against overheating, brake fade and performance decline due to water absorption. This extended life (50,000 mile) fluid is also formulated to prevent corrosion of all metals within the braking system.  This formula is safe to use in all DOT 3 braking systems (ABS, disc or drum) and can mix with any DOT 3 fluid. It is recommended to only use the DOT fluid specified for your car, as using a different DOT product can affect the boiling point or replacement interval if the wrong fluid is used.

Product Features:

• 50,000 Mile Fluid Life
• Prevent Overheating & Brake Fade with High Grade Formula
• Protects against performance decline due to water absorption. Prevents corrosion of all metals within the braking system.
• Synthetic, Extended Fluid Life Formula

Valvoline Import Multi-Vehicle Automatic Transmission Fluid is specifically formulated for use in most Toyota, Nissan, Honda and other imported vehicles. It is formulated with all synthetic base stocks and a proprietary additive system to ensure optimal transmission performance in a wide variety of vehicles. Valvoline Import Multi-Vehicle ATF can also be used in many domestic vehicles. It meets requirements of General Motors and Ford vehicles. Recommended for use in the following applications: Ford MERCON®, GM DEXRON®-II and DEXRON®-III, BMW LT 71141 and ETL-7045E, Nissan/Infiniti Nissan ATF, Matic-D, Matic-K and Matic-J, Mitsubishi Diamond SP-II and SP-III, Subaru ATF-HP, Hyundai/ KIA SP-II and SP-III , Toyota/Lexus Type T, T-III and T-IV , Honda/Acura ATF-Z1 (except in CVTs) , Mercedes Benz NAG1 , Volvo passenger car (except AW-1), and Volkswagen/Audi TL52162. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Prestone Power Steering Fluid + Stop Leak (PSF+SL) delivers increased system life and prevents & stops system leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. The stop leak additives also prevent leaks by rejuvenating seals before they leak. Also designed with Anti-wear System Protection, Prestone PSF+SL protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Includes Stop Leak Additives to prevent and stop power steering system leaks.
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• Conventional Formula – For use in all manufacturers

Prestone Power Steering Fluid (PSF) delivers increased system life. Designed with Anti-wear System Protection, Prestone PSF protects against pump failure, squeals and clogs. This 50,000 mile fluid life is formulated for use in all manufacturers; cars, SUVs, crossovers, and light and medium duty trucks. This a conventional fluid. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 50,000 Mile Fluid Life
• Anti-Wear Protection = Increased System Life. Protects against pump failure, squeals and clogs. Corrosion protection for metals, rubber & gasket components.
• For use in all manufacturers
• Conventional Formula – For use in all manufacturers

Prestone MAX European Vehicles Power Steering Fluid (PSF) + Stop Leak maximizes and increases system life + the power to stop leaks. Stop Leak additives renew, restore and condition seals in the power steering system. These seals harden and shrink over time which are the likely cause of leaks. This formula is also great at preventing leaks by rejuvenating seals before they leak. This synthetic fluid is designed with 2X Anti-wear System Protection, which means more protection against pump failure, squeals and clogs. 100,000 mile fluid life, 2X more than conventional fluid, extends the time between replacement. This fluid is formulated for European vehicle manufacturers: Audi, BMW, Jaguar, Mini, Porsche, Mercedes, Saab, Volvo, Volkswagen and others. Many cars 2006 and newer use synthetic based fluids for longer life and better protection. Conventional and synthetic fluids can be mixed but performance and replacement intervals are reduced by the conventional fluid.

Product Features:

• 100,000 Mile Fluid Life. Synthetic Formula for longer life and more protection
• MAX + Stop Leak. Stop Leak Additives to prevent and stop power steering system leaks.
• For use in European vehicle manufacturers: Audi, BMW, Jaguar, Mini, Porsche, Mercedes, Saab, Volvo, Volkswagen and others
• 2X Anti-Wear Protection for enhanced System Life vs. conventional fluid. More protection against pump failure, squeals and clogs

75,000 miles is more than a mile marker. It’s a signal that your engine is ready for greater protection. That’s when you need Valvoline High Mileage with MaxLife Technology Motor Oil. Its exclusive formula is proven to maximize engine life in cars, trucks, and SUVs with over 75,000 miles. Our mixture is specially developed with a unique combination of synthetic and premium conventional oils to protect your high-mileage motor against wear, friction, heat, and deposits – the four major causes of engine breakdown and expensive repairs. Anti-wear additives defend critical engine components, advanced friction-fighting agents reduce heat and abrasion, added detergents clean the inside of your engine, and premium seal conditioners handle aging seals to prevent leaks. It fights sludge, corrosion and rust that can rob your engine of horsepower, fuel efficiency and longevity. From extreme temperatures and cold starts to stop-and-go traffic and frequent short trips, viscosity modifiers make sure the oil flows more easily, coats more completely, and resists thermal breakdown under even the most intense driving conditions. Its unique mixture curbs contaminants to keep high-mileage engines from burning and consuming oil that can foul spark plugs, creating higher emissions and causing your motor to run roughly.

Product Features:

• MAXLIFE TECHNOLOGY PREVENTS engine breakdown with 40% better wear protection than the industry standard
• REFRESH AGING SEALS AND PREVENT LEAKS with seal conditioners
• REDUCE SLUDGE, DEPOSITS, CORROSION, AND RUST with added detergents – keep motors clean inside
• ENHANCED FRICTION PERFORMANCE HELPS MAXIMIZE POWER with advanced friction-fighting agents
• MEETS OR EXCEEDS ALL REQUIREMENTS of ILSAC GF-6A, API SP, API SN with SN PLUS, API SN

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

You trust your car to keep you going, even after 75,000 miles. Mobil 1 Extended Performance High Mileage full-synthetic motor oil 5W-30 gives engines with over 75,000 miles the extra care they need to go the distance. Formulated to help prevent leaks, it helps to protect critical engine parts for up to 20,000 miles between oil changes, guaranteed.(1) Utilizes Mobil 1’s Triple Action+ Formula to combine outstanding engine performance, protection, and cleanliness with the added benefit of maximized engine power. This cutting-edge formula is recommended by ExxonMobil for all types of modern vehicles, including high-performance, turbo-charged, and supercharged gasoline and diesel multi-valve fuel-injected engines found in passenger cars, SUVs, light vans, and light trucks. Mobil 1 is America’s No. 1 synthetic motor oil brand at retail,(2) trusted and recommended by car builders and experienced mechanics, and is the Official Motor Oil of NASCAR. ((1)Protects for up to 20,000 miles or 1 year, whichever comes first. To learn more about the Mobil 1 Limited Warranty, visit Mobil.US. (2)Source: The NPD Group/Retail Tracking Service/Dollar Sales/PCMO full-synthetic/52 weeks ending July 1, 2023)

Product Features:

• Mobil 1 Extended Performance High Mileage full-synthetic motor oil 5W-30 is designed for engines with over 75,000 miles to go up to 20,000 miles between oil changes (1)
• Utilizes Mobil 1’s Triple Action+ Formula to combine outstanding engine performance, protection, and cleanliness with the added benefit of power
• Meets ILSAC GF-6 standards to help provide low-speed pre-ignition (LSPI) and timing chain wear protection while keeping your engine clean and helping to improve your fuel economy
• Provides excellent internal engine heat protection (up to 500 degrees F) and low temperature protection (to -40 degrees F)
• Helps extend engine life by working to prevent damaging deposits and sludge buildup
• Manufacturer Part Number: 123843
• Versatile Compatibility: Recommended for all types of modern vehicles, including high-performance, turbo-charged, and supercharged gasoline and diesel multi-valve fuel-injected engines found in passenger cars, SUVs, light vans, and light trucks.
• Trusted Brand: Mobil 1 is America’s No. 1 synthetic motor oil brand at retail, trusted and recommended by car builders and experienced mechanics, and is the Official Motor Oil of NASCAR«.

Valvoline Full Synthetic MaxLife Multi-Vehicle ATF, the No. 1 ATF product, suitable for use in 95% of vehicles. And now, it’s recommended for most belt & chain-driven continuously variable transmissions (CVT). Featuring advanced additives to prevent the major causes of transmission breakdown, it’s designed to help prevent leaks, reduce wear & tear, and maximize performance. Has improved thermal stability for longer fluid life, better viscosity stability for consistent transmission operation, and frictional enhancements for smooth gear engagements. Valv MaxLife Multi-Vehicle ATF is suitable for most Ford, GM, Toyota, Honda, Nissan, Hyundai, Subaru, BMW, Mercedes, Volvo, VW & Audi vehicles. Recommended for use in: GM DEXRON-II, DEXRON-III, DEXRON-VI, and DEX-CVT; Ford MERCON LV; Toyota/Lexus Type T, T-II, T-IV, WS, CVTF FE, and CVTF TC; Honda/Acura ATF-Z1 and Honda CVT; Nissan/Infiniti Matic-D, Matic-J, Matic-K and Matic-S; Hyundai/Kia SP-II, SP-III, SP-IV and SPH-IV; BMW 7045E, ETL 8072B, LA2634 and LT71141; Allison C-4; Mercedes-Benz NAG-1; Volvo 1161521, 1161540, 97340 and 1273.41; Subaru ATF HP, Lineartronic chain CVT and CVT-II, Lineartronic High Torque CVT, and CV-30; and VW/Audi G-052-025-A2 and G-052-162-A1. CURRENTLY UNABLE TO SHIP THIS PRODUCT TO CUSTOMERS LOCATED IN CALIFORNIA

Product Features:

• FOR USE IN 95% OF VEHICLES INCLUDING MOST CVTs in operation with US registered light duty applications
• HIGH PERFORMANCE CONDITIONING AGENTS prolong seal elasticity to prevent leaks
• IMPROVED DURABILITY & TRANSMISSION LIFE with anti-wear technology to avoid costly repairs
• ENHANCED HIGH & LOW TEMP PERFORMANCE supports transmission fluid in all weather situations

Valvoline ATF for MERCON V Applications is a high-quality transmission fluid meeting and exceeding the requirements of the Ford Mercon V specification which covers most Ford passenger cars and light-duty trucks (except those specifying MERCON SP, MERCON LV, MERCON ULV or Type F fluids), including Lincoln and Mercury, as well as most pre-2006 GM vehicles and many imports. Recommended for use in the following applications: MERCON V, MERCON, DEXRON-III, DEXRON-II, Caterpillar TO-2, Allison C-4. Other applications include Power steering fluid where a DEXRON or MERCON fluid is recommended. Suitable to use in Nissan Matic D, Matic J and Matic K.

Product Features:

• Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Valvoline Multi-Vehicle Transfer Case Fluid is a full synthetic product meeting the performance needs for transfer cases recommending Ford XL-12 and GM Auto Trak II specifications or ATF fluids (DEX/MERC, ATF +4, etc).

Product Features:

• Recommended for use in most Ford, GM and FCA (Dodge, Jeep) models
• Formulated to help prevent gear wear and protect against rust and corrosion
• Formulated to deliver enhanced protection against deposits
• Helps provide better protection during extreme operating conditions

Most transmissions are automatic. Now, so is choosing an ATF. Introducing Valvoline Restore & Protect Automatic Transmission Fluid, a premium full synthetic ATF suitable for use in 95% of vehicles. Leveraging innovation from our groundbreaking Valvoline Restore & Protect Motor Oil, the same trusted technology is now available in transmission care. Restore & Protect ATF provides up to 97% deposit removal with Active Dissolve Technology, so there’s no need to add a transmission cleaner. Valvoline’s full synthetic formula outperforms conventional ATF with outstanding protection against friction, thermal stability and transmission breakdown. The high performance multi-vehicle protection revitalizes, defends and maximizes automatic transmission life. Whether it’s a Ford, GM, Toyota, Honda, Hyundai, Subaru, BMW, Mercedes, VW and more, you get exceptional performance in any driving condition. For unsurpassed deposit removal and smoother shifting, trust Valvoline Restore & Protect Full Synthetic Automatic Transmission Fluid, from the number 1 ATF brand.

Product Features:

• Removes up to 97% of damaging deposits with Active Dissolve Technology, so you can skip the transmission cleaner
• The number 1 ATF brand brings the same innovation from Valvoline Restore & Protect Motor Oil to its groundbreaking automatic transmission fluid technology
• Valvoline Restore & Protect Automatic Transmission Fluid is suitable for use in more than 95% of ATF vehicles in operation with US registered light duty applications
• Premium full synthetic formula with advanced additive chemistry fights harmful friction and thermal breakdown to help prevent costly transmission repairs
• Proven to maximize transmission life, the high performance protection revitalizes, defends, minimizes deposits and ensures smooth shifting
• Recommended For Use In Applications Requiring Dexron 6, Dexron 3, Dexron 2, Mercon Lv, And Jaso M315-2013 1A-Lv

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands of many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON*, DEXRON*-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

• Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, MERCON LV and Allison C-4.

Product Features:

• Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
• Enhanced anti-shudder protection for smooth shifting and maximum power transfer
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures