from

$149.99

Transpak – 1970 to 1982 Ford, Lincoln, Mercury C4 Recalibrate your automatic transmission for optimum performance Select the mode that best suits your application Improves transmission life Transmission removal not required APPLICATION: 1970 to 1982 Ford,

Product Features:

Recalibrate Auto. Transmission
Optimum Performance
Select Your App. Mode
Improves Transmission Life
Trans. Removal Not Required

from

$186.99

Product Features:

Mechanical Operation
Fuel Sending Unit Not Included
For Small-Block 289-351 Ford Engines
In Tank Mounting Type
110 GPH

from

$369.99

RngPnn

from

$49.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PTFE offers the best in fluid and high-temperature compatibility and contact sealing surface can run on undersize shafts, seal minor imperfections and virtually eliminate shaft wear.
Optimizes performance under high crankcase vacuum conditions, elevated temperatures and high RPM levels.
Not intended for use in emission controlled vehicles.

from

$244.99

A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.

Product Features:

Gains Both Performance and Longevity
Will Handle Any and All Torque
Out Lasts Rubber

from

$59.99

MSD Ignition control are easy to install, but we also offer several plug-in harnesses. These are especially handy for quick installation on late model vehicles! The harnesses plug directly into your factory coil and harness then four color coded wires plug into the corresponding wires of the MSD. Two wires go from the MSD to the battery and you’re done with no cutting or splicing!

Product Features:

Splice free installation
Plugs directly into factory coil

from

$65.99

MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase

Product Features:

Rotor phasing can be adjusted.
Ideal When Atomic TBI Is Controlling The Timing

from

$599.99

Unilite Electronic Ignition Distributor Series 37

from

$52.99

Designed to allow additional adjustment of the clutch fork height to eliminate clutch release problems when installing a high performance clutch. Recommended for use with Lakewood safety bell housings. Available for most GM, Ford, and Mopar applications. Adjustable dowel pins correct for improper register bore alignment of bell housing.

Product Features:

Allows Additional Adjustment
Eliminates Clutch Release Problems

from

$399.99

The X4 Performance Programmer connects high-performance tunes to your vehicle for an immediate boost in horsepower and torque. Awaken your engine to its maximum real potential with preloaded, dyno-proven tune files through the easy-to-use functionality. Instantly increase horsepower and torque and customizeModify a variety of parameters at the touch of a button, all while monitoring gauges on a customizable display.

Product Features:

Read vehicle performance data on a full-color LCD display for easy viewing, day or night.
Preloaded, street-tested, dyno-proven tunes boost horsepower, torque, and throttle sensitivity.
Reads and clears DTC (Diagnostic Trouble Codes) with ease.
Load up to 10 custom tune files created by any SCT Custom Tuning Dealer.
Full color LCD display
High-speed data logging/monitoring
Dual analog inputs
Most popular vehicles supported
Installs quickly and easily
Easy restoration back to stock
User adjustable vehicle parameters
USB Interface cable included
Product might not be available in all states due to local laws.

from

$281.99

Maximum performance within minutes is what this aFe Stage 1 cold air intake system delivers. Enclosed in a durable 16 gauge heat shield; a massive washable/reusable; 360 deg. conical Pro 5R air filter increases airflow resulting in an additional 6 hp; and 7 lbs./ft/ torque. This intake system also features a unique 3-angle adaptor for increased air velocity. The Pro 5R air filter is constructed with 100 percent polyurethane for long life and multiple cleaning cycles. This intake is the easiest intake on the market to install. Simply remove the factory intake and mount the 3-angle adaptor with the air filter to the MAF sensor tube and you are breathing more air and producing more power.

Product Features:

Uses Pro 5R Filter For Maximum Air Flow
Rotomolded Plastic Tube
60% cfm Flow Gain
Improved Throttle Response

from

$198.99

Product Features:

9.5 in. Length
0.312 in. Diameter
4130 Chromoly Steel Material
Black Oxide Finish
Made In The USA

from

$78.99

Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:

Direct performance replacement for Ford TFI coil
85:1 turns ratio
Lower Primary Resistance Produces High Voltage Output
Works w/Stock Ignition As Well As MSD Ignitions
CARB E.O. Approved

from

$25.49

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

Die cut silicone rubber gaskets conform to out-of-flat covers
Great for on-again/off-again situations
Not intended for use in emission controlled vehicles.

from

$387.99

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:

Excellent performance in street carbureted applications.
More vacuum allows an increase in duration for improved performance and assists power brakes.
Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

from

$823.99

Holeshot 2400 for Ford 1966-1991 C6 with 332, 352, 360, 390, 406, 427, 428, 429 cid with 1.848 in. crank pilot (3) Application: Ford 1966 to 1991 C6 with 332, 352, 360, 390, 406, 427, 428, 429 cid with 1.848 crank pilot (3) Furnace brazed impeller New pre

Product Features:

Furnace Brazed Impeller
Steel Alloy Pump Drive Tube
Heavy Duty Needle Bearing
Between Stator and Turbine
Furnace Brazed Turbine

from

$29.49

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens at 160 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully opens at Correct Temperature Consistently Regardless of engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$17.99

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.

Product Features:

HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
EASY TO REMOVE: Fast and easy Wrench-Off removal
HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers

from

$114.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$499.99

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

Certified Billet Material
Borg and Beck Clutch Pattern
Long-Style Clutch Pattern
Ring Gear Securely Mounted To Prevent Spinning

from

$43.99

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-temperature steel core/graphite faced exhaust material
Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
Conforms to and seals minor surface irregularities
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Anti-Stick Properties
Easy Removal For Disassembly

from

$119.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$24.88

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$249.99

The COMP Cams High Energy Die-Cast Aluminum Roller Rocker Arms are new rocker arms from the valve train leader that have been designed for street and moderate race use. They feature a die-cast body created from aluminum with a needle bearing fulcrum and roller tip. The die-cast, larger than stock body offers the strength properties and light weight of aluminum while the specially engineered fulcrum and roller tip decrease friction and lower oil temperatures, thus improving response and horsepower.

Product Features:

Cost effective aluminum construction provides superior strength to weight ratio
Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
Durable design increases valve lift while withstanding the rigors of moderate race use
Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

from

$350.99

These Magnum Roller Rocker Arms for Ford V8 289-351W (Rail Type) 1968-89 applications are the ultimate street rocker. With a 3/8″ stud diameter and 1.6 ratio, they are designed for serious performance enthusiasts. All Magnum Roller Rocker Arms are constructed from 8620 chromemoly steel, which is a superior material that will not flex and assures maximum lift. Their roller tip reduces friction, while stiff design and superior ratio accuracy yield more effective valve lift. With a 15 to 30 horsepower increase over other rocker arms, Magnum Roller Rockers are perfect for performance applications with less than 350 lbs. open spring pressure. Don’t accept inferior products or cheap knock-offs, look for the COMP Cams logo stamped into the underside of every Magnum Rocker.

Product Features:

Ultimate street rocker designed for serious performance enthusiasts
Constructed from 8620 chromemoly steel, a superior material that will not flex and assures maximum lift
Roller tip reduces friction while stiff design and superior ratio accuracy yields more effective valve lift
15 to 30 horsepower increase over stock rocker arms
Use in any applications with less than 350 lbs. open spring pressure