from

$1382.99

(PDT)Premium Drivetrain Transmissions are remanufactured to original equipment (OEM) demanding specifications by an OEM builder. Each transmission assembly is manufactured with the highest technology equipment, the most intelligent engineering support, and the best practices available in remanufacturing today.

Product Features:

All transmissions are completely disassembled and cleaned. All cases are media blasted. Internal parts are inspected for wear or damage and replaced as required. All bushings are inspected and replaced as required.
100% of friction components are replaced with upgraded heavy duty parts.
Drum assemblies are air checked and side play is checked to assure proper clearance. 100% of seals, o’rings and gaskets are replaced.
100% of solenoids are checked and replaced if they do not pass duty cycle tests. Internal wiring harness are checked and replaced as necessary. Valve bodies are disassembled, cleaned, and measured for wear. Valve body valves and valve bores are inspected and valve bores are machined as required. Completed valve bodies are tested for proper operation prior to dyno testing.
Transmissions are assembled, end plays are set and fasteners are torqued to the required specification.
100% of transmissions are dynamometer tested to ensure proper pressures and shift quality throughout the operating range. All upshifts and downshifts are checked against preset parameters. Torque converter stall speed and lockup is verified on the dyno
Product might not be available in all states due to local laws.

from

$70.99

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

from

$231.99

Pre-filled clutch hydraulic assembly. Includes a clutch Master cylinder, clutch slave cylinder and line.

Product Features:

Includes pressure control valves, check valves, and fittings for ease of installation and maintaining OE performance levels
Each unit includes vehicle-specific bulletins for accurate installation
TECHnovation brand pre-filled hydraulic assemblies are developed, manufactured and tested to meet OEM standards
Engineered and supported in the U.S.A. by our tech support team of experts in clutch system function

from

$6.99

AT CONTR SHAFT SEAL

from

$15.99

AT OIL PUMP SEAL

from

$4.27

Input Shaft Seal

from

$158.99

AT OVERHAUL KIT

from

$193.99

Remanufactured using industry-leading techniques to assure enhanced torque performance and extended life. Each unit is harmonically balanced and leak tested with any inherent OE weaknesses corrected. Pro-King torque converters are subject to random ISO 9001 quality tests before leaving the factory.

Product Features:

Fluid Balanced

from

$23.29

Product Features:

Transmission line fitting kit
Ford; 5/8″-18 inverted flare, deep thread
Helps simplify transmission cooler installation
Allows for auxiliary transmission cooler installation without cutting OE lines
Crafted from high-quality material that makes it durable and longer-lasting
A high quality, direct fit OE replacement
Easily connects the transmission cooler line to the cooler hose
Hose clamps required

from

$188.99

AT CONTR SOLENOID

from

$16.42

AT Pan Gasket

from

$6.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Low swell in hydrocarbon fluids
Design type: spring loaded; multi-lip
Provides good low temperature capability
Temperature range: -40°F to 225°F; -40°C to 107°C
Delivers quality and reliable performance for every type of repair

from

$39.99

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

Designed to OE standards for ease of installation
Our parts are 100% tested to verify both mechanical and electrical switching performance
Decades of industry leading research and development focused on meeting the technician’s needs
Robust design and high grade materials meet the stringent demands of today’s service professional
BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

from

$18.22

AT Idler Gear Bearin

from

$13.79

Value-priced seal meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$33.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$26.99

The purpose of the mount is to support the engine and transmission on the chassis and dampen vibration and noise from reverberating to the rest of the vehicle. Engine and Transmission Mounts are engineered and manufactured to meet or exceed OEM specifications using the latest CAD/CAM engineering process to ensure superior quality, form, fit and function. Only premium quality materials are used in the manufacturing process to guarantee precise performance and maximum durability. Applicable to FORD 90-02; MAZDA 91-97;. Please verify your application.

Product Features:

MAXIMUM LIFE & PERFORMANCE: Both natural and SBR (Styrene Butadiene) rubber provide good abrasion resistance and aging stability to ensure maximum life and performance.
MEETS OR EXCEEDS DUROMETER MEASUREMENTS: All rubber material is manufactured to specific Durometer (hardness) measurements based on the vehicle’s application requirements.
HARDENED STEEL FASTENERS: All fasteners are made of hardened steel with heat treated Grade #5 bolts.
SUPERIOR BOND: A special Chemlock® bonding agent is used to ensure a superior rubber-to-metal bond.
HYDRAULIC MOUNT DESIGN: Hydraulic Mounts (applicable where OE) are designed for most front wheel drive vehicles because transverse drive train mounting.
For Years: 1990-2002
Weight approx: 4 Lbs
MOUNT HOLES ON CENTER: 5.5 INCH /139.7 MM
STUDS ON CENTER: 3.15 INCH/80.00 MM
HEIGHT: 2.94 INCH/74.68 MM
NOTE: INTERLOCK

from

$37.49

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

from

$9.29

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features: