Mazda B4000 Drivetrains

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits AMC Model 35 IFS
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to FORD 84-98;. Please verify your application.

Product Features:

• MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
• HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
• READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
• For Years: 1984-1998
• Weight approx: 2 Lbs
• BEARING ID / BORE: 1.2570 INCH / 32 MM
• CENTERLINE: 2.00 INCH / 51 MM
• MOUNT WIDTH: 5.90 INCH / 150 MM

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• For U-Joints 354, 369 & 437G
• Contains two 1.59″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Available in both caged design and full complement
• Industry leading coverage
• Professional technicians know they can depend on National

Double Cardan CV Ball Seat Repair Kit

The components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of an axle of a vehicle or trailer. Check the leaf spring dimensions and other relevant application details to select the right type and size U-bolt kit for your needs.

Product Features:

• Reliable hardware – the components in this leaf spring axle U-bolt kit are designed to securely hold the leaf spring or leaf spring bundle to the underside of a vehicle or trailer axle
• Check fit – carefully review the dimensions of the leaf springs that will be used and other relevant application details to select the right type and size U-bolt kit for your needs
• Durable construction – the components in this kit are engineered from quality materials for reliable performance and long service life
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

This CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself. Made of quality components, this kit is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this CV joint boot kit contains the parts required to repair the CV joint on specified vehicles without removing the joint itself
• Ideal solution – this kit is a reliable replacement for original components that have failed due to wear
• Durable construction – this kit is made from quality components to ensure reliable performance and a long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Yukon 1541H alloy 5 lug right hand rear axle for (’93-’97 only) Ford 7.5″ and 8.8″ Ranger with a length of 27-5/16″ inches and 28 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

• Fits 1993-1997 Ford Ranger
• Right hand side
• 28 spline
• 27 5/16″ long
• 5 lug

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• Machined bodies to meet the tight tolerances
• Forged and cast material to meet the performance requirement
• Minimize the flash lines for less interference
• Cleaning process induces compressive strength for increased performance
• Machined and threaded holes for mounting ease
• Rust preventative added for longer shelf life

With Clamps and Grease The EMPIRE CV Joint Boot Kit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function. Install one boot kit per wheel to restore vehicle to optimal condition and protect the constant velocity joint from contamination

Product Features:

• Help restore the vehicle to like-new condition
• Constructed of high strength OE materials
• Resists environmental contamination
• Protects the CV joint from premature failure

Differential Cover

7.5″ Ford notched cross pin shaft. Not Auburn gear. This cross pin shaft is not compatible with Powertrax Lock Rights or Spartan Lockers.

Product Features:

• Notched cross pin shaft for Ford 7.5″
• 3.73 and up ratios
• Not compatible with Spartan Locker or Powertrax Lock Right

Yukon axle bearing & seal kits are specially designed for each application & use all high quality bearings & seals. R1563TAV axle bearing and seal kit, TorringtonBrand, 2.250″ OD, 1.400″ ID. This axle bearing & seal kit services one side only.

Product Features:

• Includes axle bearing and seal
• Services one side
• Torrington Brand
• 2.250″ O.D.
• 1.400″ I.D.

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific, providing unsurpassed quality for a seal you can trust
• Validated for fit, form, and function
• Engineered for the sealing repair environment
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Double Cardan CV Centering Yoke

Sealed Power® parts provide innovative designs, use leading edge materials and utilize ISO & QS certified manufacturing in order to deliver top quality products that meet the rigorous demands of today’s modern engines.

Product Features:

• Steel-backed Babbitt lining material
• Used in automotive and high-performance
• Babbitt is designed to perform under extreme loads w/o damaging other engine parts
• Babbitt is more environmentally friendly than other material
• ISO & QS certified manufacturing

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Pinion gear thrust washer (0.750″ shaft) for 8.8″ Ford.

Product Features:

• Pinion gear thrust washer
• Fits Ford 8.8″
• 0.750″ I.D.

Redline Synthetic “Shock Proof” Oil. 4 Quarts.

Product Features:

• Includes four quarts of Redline Shockproof oil

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• KIT, SUPER BRG & SEAL-FORD 7.5 TIMK TIMKEN

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Spindle bearing and seal kit
• Includes all components required to complete the repair
• Controlled heat treating process for lasting performance and extended bearing life
• Industry leading coverage
• Professional technicians know they can depend on National

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Controlled heat treating process for lasting performance and extended bearing life
• Industry leading coverage
• Professional technicians know they can depend on National