Lexus GX470 Differentials

Product Features:

• Side adjuster lock
• Fits Toyota V6

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear. This kit fits applications with a 27 spline pinion.

Product Features:

• Fits Toyota V6 rear
• Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

Product Features:

• Seal housing for Toyota 8″ and V6
• Includes o-rings

V6 standard Open case, bare.

Product Features:

• Standard open carrier case
• Does not include spider gears
• Fits Toyota V6

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket. This kit fits applications with a 27 spline pinion.

Product Features:

• Fits Toyota V6 rear
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

• Fits Toyota V6 rear
• 8.125″ ring gear diameter
• 29 spline pinion
• 10 ring gear bolts
• 4.56 ratio

Outer oil slinger for Toyota 7.5″, 8″, V6 & Landcruiser.

Product Features:

• Outer oil slinger for Toyota 7.5″, 8″, V6 and Landcruiser

Product Features:

• Fits Toyota V6 rear
• Fits ABS and non-ABS applications

The Spartan Locker, by USA Standard Gear, provides reliable traction at a low cost. Give your vehicle great traction and save some cash. Choose a Spartan Locker for better traction. The Spartan locker by USA standard gear is a mechanical locker that replaces the spiders in a standard case. The Spartan locker’s design does not use the thrust washers and has a revolutionary spring and pin design that makes installation a snap! The couplers and drivers are made from 9310 steel, for added strength. Each Spartan locker carries a one year warranty against defect.

Product Features:

• Fits Toyota 8″ and V6
• Made from 9310 steel for added strength
• Works with stock side gears in standard carrier case

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Low swell in hydrocarbon fluids
• Design type: spring loaded; multi-lip
• Provides good low temperature capability
• Temperature range: -40°F to 225°F; -40°C to 107°C
• Delivers quality and reliable performance for every type of repair

Product Features:

• CONSISTENT PERFORMANCE: Matched cup and cone components ensure consistent performance
• PREMIUM MATERIALS: Precision manufactured using high-quality materials for durability and performance
• OE-STYLE DESIGN: Engineered to meet OE specifications
• COMPREHENSIVE COVERAGE: Industry-leading coverage for domestic and import applications
• RIGOROUS TESTING: Comprehensive testing throughout design and development processes by National engineers for quality you can count on

Toyota 8″ & V6 gasket.

Product Features:

• Dropout gasket
• Fits Toyota 8″ and V6

Product Features:

• Side adjuster lock bolt
• Fits Toyota 8″ 4 or 6 cylinder engine

Differential

Product Features:

• Cross pin shaft
• Fits Toyota V6

Product Features:

• Pinion depth shims for Dana Spicer 60 and 70U

Valvoline MaxLife Multi-Vehicle ATF is a full-synthetic formulation with advanced additives to prevent the major causes of transmission breakdown and help extend transmission life.  Developed to help prevent leaks, maximize transmission performance, reduce transmission wear, and maintain smooth shifting longer than conventional fluids. It is suitable for use in a broad range of ATF applications including most Ford, GM, Toyota, Honda, Nissan, Hyundai, BMW, Mercedes, Volvo, VW & Audi. Recommended for use in the following applications: GM DEXRON-II, DEXRON-III, DEXRON-VI, Ford MERCON LV, Toyota/Lexus Type T, T-II, T-IV, WS, Honda/Acura, ATF-Z1, Nissan/Infiniti Matic-D, Matic-J, Matric-K, Matic-S, Hyundai/Kia SP-II, SP-III, SP-IV, SPH-IV, BMW 7045E, ETL 8072B, LA2634, LT71141, Allison C-4, Mercedes Benz NAG-1, Volvo 1161521, 1161540, 97340, 1273.41, and VW/Audi G-052-025-A2, G-052-162-A1. For CVT applications Valvoline recommends Valvoline Full Synthetic CVT Fluid.

Product Features:

• Formulated with full-synthetic base oils and long life friction modifiers to help improve smooth shifting, eliminate slippage and shudder, prevent clutch wear and improve drivability longer than conventional fluids
• High-performance seal conditioners maintain and preserve the elasticity of seals to help prevent leaks in high mileage transmissions
• Developed with anti-wear technology to help improve transmission durability
• Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:

• Fits Toyota Tacoma and T100 rear with factory locking differential
• Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and silicone.

V6 standard Open pinion gear Thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits Toyota V6

T100 & Tacoma w/LOC pinion nut.

Product Features:

• Pinion nut
• Fits Toyota Tacoma and T100 with factory locking differential

Product Features:

• Conversion kit
• Fits Toyota V6 rear with 29 spline pinion
• Includes yoke , pinion seal, and pinion nut

V6 Toyota solid crush sleeve replacement spacer kit, preload.

Product Features:

• Crush sleeve eliminator kit for Toyota V6

21 Piece bearing race driver set. (Box wt: 140lbs) No return.

Product Features:

• Bearing race driver set
• 21 pieces
• All steel construction

V6 side gear Thrust washer.

Product Features:

• Side gear thrust washer
• Fits Toyota V6

Replacing a worn wheel bearing usually requires a time-consuming procedure with a shop press. This Dorman OE FIX loaded axle includes all critical components already assembled for a fast, simple, safe install.

Product Features:

• Easier installation – this loaded axle assembly includes a new axle shaft, wheel bearing, hub and backing plate pre-assembled and ready to install right out of the box
• Time saver – eliminates frustrating, unpredictable work required to replace bearings without damaging other components
• Simpler solution – eliminates the need to use potentially dangerous shop press to perform complete bearing repair
• Trustworthy quality – backed by engineers and inspectors in the United States, with decades of aftermarket experience