from

$181.99

Dana 60 & Dana 70 Power Lok clutch set (steel & fiber).

Product Features:

Clutch kit
Fit Dana Spicer 60, 70, 70U and 70HD Powr Lok positraction

from

$4.99

Product Features:

Side gear thrust washer for Dana Spicer 60, 70, 70U, 70HD and 80
Fits standard open differentials only

from

$509.99

Product Features:

Trac Loc positraction carrier case
Does not include spider gears
Fits Dana Spicer 60
4.10 and down ratio only
ABS and non-ABS compatible

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$7.99

Dana 50 Dana 60 Dana 70 & Dana 80 roll PIN, 0.225″ DIA, for X/P shaft, 1.87″ LNG.

Product Features:

Roll pin for Dana Spicer 50, 60, 70, 70U, 70HD and 80
0.225″ diameter
1.870″ long

from

$7.99

Dana 60 & Dana 70 Power Lok case bolt.

Product Features:

Power Lok case bolt for Dana Spicer 60 and 70
7/16 x 14 thread
3.5″ long
9/16″ hex head

from

$389.99

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

Fits Dana Spicer 70U
Uses Koyo bearings and races
Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, oil baffles and slingers, thread locker, marking compound with brush and gasket.

from

$16.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$36.99

Product Features:

Bulkhead fitting kit
Includes bulkhead fitting, outer fitting and o-ring

from

$104.99

Product Features:

Carrier shims for Dana Spicer 60 and 70U

from

$62.99

Spectre’s Chrome GM Differential Covers feature a 14 bolt design and include the chrome bolts and gasket needed for an easy install. Made to OEM specifications these differential covers are triple chrome plated ensuring they perform as well as they look. This product fits the following vehicles with a 10.5 inch ring gear: 73-’87 Chevy/GMC 3/4 & 1 Ton 2/4WD (rear), ’75-’00 Chevy/GMC Dually 2/4WD (rear), ’88-’99 Suburban 3/4 Ton 2/4WD (rear). Includes 14 SAE standard chrome bolts for installation. You’ll need to supply your own bolts if your application requires metric bolts.

Product Features:

Fits the following vehicles with a 10.5 inch ring gear: 73-’87 Chevy/GMC 3/4 & 1 Ton 2/4WD (rear), ’75-’00 Chevy/GMC Dually 2/4WD (rear), ’88-’99 Suburban 3/4 Ton 2/4WD (rear).
Triple chrome plated steel construction
14 bolt design
14 chrome 5/16 inch -18 x 3/4 inch differential cover bolts included

from

$301.99

Yukon standard open spider gear replacement kit for Dana 60 and 61 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. All components come with a one year warranty against manufacturing defects.

Product Features:

Spider gear kit
Fit Dana Spicer 60 open differential with 35 spline axles
Includes two side gears, two pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$10.49

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$689.99

The Yukon carrier bearing Puller works with an impact gun to quickly and safely remove carrier bearings without damaging them. This unit comes with a handy bench top stand and works with up to most standard one ton applications. This unit is works with differentials up to one-ton applcations. It is not compatible with Dana 70HD, Dana 80, 10.25″ & 10.5″ Ford, or GM & Chrysler 11.5″ differentials.

Product Features:

Carrier bearing puller
Works with an impact gun to safely and easliy remove carrrier bearings
Not compatible with Dana 70HD, Dana 80, Ford 10.25″ and 10.5″ or Gm and Chrysler 11.5″ applications

from

$5.99

Product Features:

Outer oil slinger for Dana Spicer 60, 70, 70U and 70HD

from

$323.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$15.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$215.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits HM88510 race
All steel construction

from

$4.99

Replacement ring gear bolt for Dana 60, 70, 70U & 70HD, 1/2″ x 18.

Product Features:

Ring gear bolt for Dana Spicer 60, 70, 70U and 70HD
1/2″ x 18 thread

from

$6.49

Product Features:

DANA PRELOAD SHIMS (D60 & D70)

from

$266.99

Product Features:

GM10.5″ INTERNAL KIT (OPEN) 30 SPL

from

$11.99

Product Features:

CRUSH SLEEVE 14 BOLT 10.5 3116

from

$14.29

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National