from

$1119.99

Differential

from

$10.99

14T ring gear bolt 4.11 & down. 9/16″ x 18. 2.085″ overall length.

Product Features:

Ring gear bolt for GM 10.5″ 14 bolt truck
4.11 and down ratio
1/2″ x 18 thread
2.085″ overall length

from

$114.99

Axle shaft damaged or bearings worn out: This axle shaft directly replaces the original equipment on certain vehicles, complete with all necessary application-specific installation components.

Product Features:

Product Features:

Direct replacement – this axle shaft replaces the original equipment on specific vehicle years, makes and models
Complete kit – each shaft includes critical installation hardware and components needed for specific vehicle applications
Durable construction – designed to rigorous standards and tested to ensure performance
Trustworthy solution – backed by team of engineers and quality control specialists in the United States

from

$16.49

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both on and off-road, check out Motive Gear. Motive Gear products can be found in the winner’s circle at racing events worldwide. The superior quality of Motive Gear components is the result of years of racing development, outstanding design and state-of-the-art manufacturing methods. Extensive testing is performed on all products by our in-house engineers.

from

$304.99

Yukon 1480 Lifetime Series U/Joint. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.

Product Features:

Clutch kit
Fits GM 10.5″ 14 bolt truck with Eaton positraction
Carbon fiber clutches

from

$5.99

Product Features:

Pinion nut washer
Fits Dana Spicer 80

from

$379.99

USA Standard ring & pinion sets are the right choice to add confidence to your install. USA Standard Gear offers a full line of ring & pinion sets for a variety of common & hard to find applications. USA standard gear offers a standard one year warranty against defects on their ring & pinion sets.

Product Features:

Fits Dana Spicer 80
11.25″ ring gear diameter
37 spline pinion
12 ring gear bolts
4.30 ratio

from

$323.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$969.99

Yukon replacement loaded standard open case For Dana 80, 35 spline, 4.10 & up, non-ABS.

Product Features:

Standard open carrier case
Includes spider gears
Fits Dana Spicer 80 with 35 spline axles
4.10 and up ratio only
Not compatible with ABS applications

from

$11.99

Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands of many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON*, DEXRON*-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:

Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
Enhanced anti-shudder protection for smooth shifting and maximum power transfer
Developed with anti-wear technology to help improve transmission durability
Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures

from

$19.99

Product Features:

Oil baffle
Fits Dana Spicer 80

from

$1110.00

The Yukon Dura Grip provides aggressive yet smooth traction to give you the confidence & performance you need. Get longer life and better traction with the heavy duty Yukon Dura Grip Positraction. The Yukon Dura Grip uses a nodular case and forged 4320 internals for added strength along with composite clutches for high performance and long life. All units are Rebuildable and many offer upgrades to increase aggressiveness for racing applications. Each unit carries a one year warranty against defects.

Product Features:

Fits GM 10.5″ 14 bolt truck
4.10 ratio and down only
Clutch style positraction
Internal gears are manufactured using forged 4320 steel and cut to provide stronger teeth
Fully rebuildable
Assembled in the USA

from

$275.99

Product Features:

DANA-60 R/P 3.54 STD MG 24813-5X (USES PRE-LOAD SHIMS)

from

$7.99

Dana 70 & Dana 80 pinion gear Thrust washer.

Product Features:

Pinion gear thrust washer for Dana Spicer 70 and 80

from

$449.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1998 and up GM 10.5″ 14 bolt truck
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$7.99

14T side gear Thrust washer.

Product Features:

Side gear thrust washer
Fits GM 10.5″ 14 bolt truck

from

$7.99

Differential Cover B

from

$92.99

Product Features:

Fits GM 10.5″ 14 bolt truck
Steel

from

$14.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$27.99

Replacment Pinion depth shims for Dana 80 (between pin head & bearing).

Product Features:

Pinion depth shims for Dana Spicer 80
Fits between pinion head and bearing

from

$28.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$74.99

All Motive Gear products are engineered for their specific application and manufactured in state of the art facilities. All of our products undergo rigid quality control processes to insure proper fit, performance and longevity. Motive Gear products can be found in the winners circle at NHRA, IHRA, NMRA, NMCA, SODA, SCORE, BITD, Ultra-4 and NASCAR events because we offer unmatched selection and quality demanded by racers and their crew chiefs – the same quality and selection demanded by DIY customers and top mechanics. With four warehouses strategically located across North America, most Motive Gear orders arrive within 2-4 days. Win with Motive Gear!

from

$48.99

10.5″ GM 14 bolt truck pinion nut. 1 1/2″ socket, 15/16″ x 16 thread.

Product Features:

Pinion nut for GM 10.5″ 14 bolt truck
15/16″ x 16 thread
1.5″ socket

from

$5.99

This differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this differential crush sleeve is designed to match the fit and function of the original sleeve on specified vehicles
Required replacement – when servicing the differential
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience