Ford Victoria Alternators and Starters

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. Individual motor components are available to service any failed part within the motor such as brushes, bushings, and starter drive unit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

The charging system has been required as long as we have had a need for an electrical system and from research it’s been since the requirement of horns in motor vehicle in the early 1900’s. An alternator is a voltage generator that uses mechanical energy to rotate a set of magnets within a field of windings called a stator. The alternating current (AC) voltage created by the spinning magnetic field is converted into a usable direct current (DC) voltage with a rectifier and then regulated by a voltage regulator so that the voltage level in the electrical system stays within a specific operating range. The alternator provides all the voltage needed to operate a vehicle, the battery is only used as a reserve for heavier load conditions, as a voltage source for the engine starting system, and to supply a small amount of voltage to the electromagnets in the alternator which boosts the magnetic field in the alternator and increases voltage output.

Product Features:

• Application matched components ensure the charging system can be returned to like new condition.

CARQUEST Voltage Regulators are engineered and created by an automotive charging system manufacturer designed to meet or exceed OEM specifications. By fully understanding how the alternator and the voltage regulator interact ensures that the CARQUEST volt

Product Features:

• CARQUEST Voltage Regulators are designed to match OE fit, form and function. Fitted with critical OEM electronic components results in longer life expectancy.
• CARQUEST Voltage Regulators are mechanically designed with utilization of surface mount technology, robust mechanical housing, and consistent encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators uses surface mount technology and uniform encapsulation to protect against moistures & vibration.
• CARQUEST Voltage Regulators are 100% individually tested for all product functionalities that includes the proper voltage set-point, power capabilities, and other product specifications.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Controlled heat treating process for lasting performance and extended bearing life
• Industry leading coverage
• Professional technicians know they can depend on National

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

The starting system consists of the rotating electrical motor and solenoid which may be mounted on the starter motor or mounted remotely. The electric motor drives a gear which engages with the engine’s flywheel located at the rear of the motor, when the motor is energized, the motor will turn the engines crankshaft. The starter solenoid is an electric relay, or switch used to provide power to the starter motor or any electrical device that requires high amperage to operate. A low amperage wire winding within the solenoid will create magnetic force when voltage is applies from a remote switch, such as the ignition switch or another type of remote mounted switch. The contacts within the relay carry a high amperage load to run an electric motor or some other type of high load circuit.

Product Features:

• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.

Carquest Premium alternators are premium constructed, original equipment (O.E.) replacement parts with industry-leading warranties. Our Carquest Premium alternators are designed to meet or exceed OE specifications for fit, form and function. Our alternators are remanufactured by an IATF/TS 16949 certified supplier that meets the highest standards achievable. We replace all wear components (brushes, bushings and bearings) with new components to ensure long-life. All critical components are electronically tested during assembly and the entire unit is 100% tested, ensuring proper performance backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

These Mr. Gasket chrome alternators are remanufactured to exceed original equipment specifications for maximum dependability. This Ford 1G style small case 80 amp alternator can be used as an original equipment replacement with the original equipment external regulator. This is not a 1-wire alternator.

Product Features:

• Fits Most 1961-’85 Ford Vehicles w/ Small Case Alternator
• Bolt Spacing 6.875″
• Ford 1G Style Small Case Alternator
• 80 Amps
• Chrome Plated Finish
• includes V-Belt Pulley – 1-Groove
• Use w/ OEM Style Regulator

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Product Features:

• Brand may vary by location

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Product Features:

• Permanent Magnet For High Efficiency
• Clears All Headers
• Cranking Power For Up To 10.5:1 Compression
• Mounting Bolts And Dyno Test Results Included
• Limited 1 Year Warranty For Street Use

Carquest Professional starters are 100% new units that are built to meet or exceed original equipment (O.E.) specifications. Our new starters are engineered and built by an IATF/TS 16949 certified supplier that meets the highest standards achievable. Carquest Professional starters are re-engineered to include improvements and enhancements (where applicable) to the OE design to extend longevity and service life. Our new starters are built with all new components and are 100% triple-tested to ensure high quality that is backed by an industry-leading warranty. We also offer technical support at 1-800-228-9672 for product questions, diagnostic troubleshooting and installation assistance by ASE Certified Technicians.

Product Features:

• Designed to meet or exceed OE specifications for fit, form and function
• Manufactured by an IATF/TS 16949 supplier that meets or exceeds the highest standards in the industry
• Housings are 100% new with dimensions computer gauged and measured to ensure proper fitment
• All new components are utilized to ensure long service life
• Internal electronics are upgraded for heavy duty reliability (where applicable)
• Armatures and commutators are 100% load tested
• Application-specific technical bulletins included where applicable
• All units are 100% triple tested to ensure quality and performance
• Technical support team staffed with ASE Certified Technicians: 1-800-228-10468

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing ┐ utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) ┐ in the connector terminal design process ensures speed-to-market and a precise connector fit guaranteed.
• Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

Edelbrock part #1146 is a Generator Bracket kit for our 1109, ’49-53 Ford Flathead Triple Deuce Intake Manifold. It is for those using the manifold in conjunction with a stock style generator. The purpose of kit is to remedy the interference between the g

Product Features:

• Offset Bracket
• Longer Fan Belt Is Required
• Includes 1.25 in. Water Neck
• Natural Finish
• Made In The USA

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

• High-quality products that meet OE appearance and performance to