Ford LTD Crown Victoria Performance and Racing Products

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

• Rynite Injection Molded Caps And Retainers
• Designed w/Performance In Mind
• High Quality; Voltage Insulating Material
• Stainless Terminals

Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Results in quicker starts, improved idle quality, and crisper throttle response. Compatible with late model Ford EEC-IV computer controlled ignition system equipped with a TFI distributor. Direct OEM replacement. Can also be used with an ACCEL, Mallory, Crane, Holley or MSD capacitive discharge ignition system. Special high temperature epoxy resists shock and vibration, while increasing thermal conductivity. Brass coil wire contact increases energy efficiency and resists corrosion better than aluminum. High dielectric strength ACCEL Yellow over-molded housing.

Product Features:

• Direct Plug In Replacement Direct OE Fit
• Advanced Bobbin Technology
• Standard Motor Products SMP Fd-478
• MSD 5527
• Standard Motor Products SMP Fd-478
• MSD 5527
• Resists Shock And Vibration
• Resists Corrosion

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

• Manufactured from high-temperature steel core/graphite faced exhaust material
• Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
• Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
• Conforms to and seals minor surface irregularities
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use
• Anti-Stick Properties
• Easy Removal For Disassembly

The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.

Product Features:

• Indicates coolant temperature
• Helps prevent coolant injuries
• Fahrenheit and centigrade readings
• Color-coded temperature ranges
• Integrated coolant reclamation valve
• Improves under-hood appearance
• Chromed crown with a colored trim ring

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts,

Product Features:

• Excellent performance in street carbureted applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

• Opens At 195 Degrees
• Designed to Resist Large Variations of Coolant Pressure at High RPM
• Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
• For High Performance Street, Drag Race, and Oval Track
• Copper & Brass Construction – Resists Corrosion
• High Flow

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.

Product Features:

• Certified Billet Material
• Borg and Beck Clutch Pattern
• Long-Style Clutch Pattern
• Ring Gear Securely Mounted To Prevent Spinning

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

• Standard Impeller Rotation
• 0.625 in. Pilot Shaft
• 0.750 in. Ball/Ball Bearing
• 5.70 in. Block To Hub Height
• Black Finish

Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts.

Product Features:

• Excellent performance in street fuel injected applications.
• More vacuum allows an increase in duration for improved performance and assists power brakes.
• Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
• Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.

Product Features:

• Service Part
• Makes Connections Quick And Easy

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Product Features:

• Rotor for Flame-Thrower cast distributors
• Replacement premium rotor with brass contact.

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It is a direct replacement for a factory one-piece rubber main seal. It’s also injection molded for a precise fit.

Product Features:

• Repairs that leaky rear main seal
• Direct replacement for stock one-piece seal
• Silicone rubber to withstand extreme oil temperatures
• Injection molded for precise fit

Precision die cast, these water necks are first polished to a high luster, then chrome plated. Features an O-ring style seal to prevent water leaks. Comes with O-ring gasket and mounting bolts.

Product Features:

• Chrome Plated
• This Is A 45 Degree Neck
• Comes With O-ring And Bolts
• Has Small Hose Fitting On It

Our DynaForce starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The DynaForce starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

• 3/4″ Depth and can be used on 157 and 164 Tooth Flywheels
• Downsized design helps clearance issues w/oil pans and exhaust
• Ball bearing supported armature and pinion gear
• 3 Hp Motor Provides Power For High Compression Engines
• Gear reduction of 4.4:1 improves torque for great cranking
• Downsized design helps clearance issues
• Mount can be clocked to assist in mounting

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• DESIGNED FOR IMPERFECT SEALING SURFACES — Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces
• SEALING TECHNOLOGIES — Exclusive sealing innovations and technologies with proprietary materials and unique design features to ensure a superior seal for your repair
• ENGINEERING EXPERTISE — Parts are designed, reviewed, validated and approved by Fel-Pro engineers through rigorous research and development
• REAL-WORLD TESTED — Parts are tested on-vehicle and validated to ensure optimal performance on the road
• EVERY PART FOR THE REPAIR — Fel-Pro gasket sets include every part needed for the repair unless otherwise noted

Edelbrock camshafts are matched to Edelbrock Total Power Package components for proven performance, taking the guesswork out of camshaft selection. They are compatible with OEM or Edelbrock hydraulic roller tappets which reduce friction, virtually eliminate break-in problems, and permit higher valve velocities for increased performance. Designed to work with Torker II manifolds for performance from 2500 to 6500 RPM, these camshafts are ideal for high-performance street, drag or marine applications. Torker-Plus cams have a slightly rough idle and are not suitable for trucks or towing applications. Hydraulic flat tappet lifters are included with each camshaft.

Product Features:

• Designed for 2500 to 6500 Performance
• Designed for Hi-Perf Street; Drag or Marine Use
• Matched to Edelbrock Torker II Intakes
• Includes Hydraulic Lifters and Assembly Lube
• Dyno Matched/Street Proven Performance
• Take The Guesswork Out Of Camshaft Selection

The Original Pro Stick shifter delivers rock-solid performance, mixed with clean design cues and compact size. This is why you see so many Pro Stick shifters at the race track. We start off with a heavy duty steel base with a hardened steel gate plate, a reverse lockout feature that only requires one hand to operate, and complies with NHRA/IHRA safety rules. Then add the billet aluminum shift handle with classic white shift knob, lightweight aluminum trigger and finish it off with a brushed aluminum cover with quick release pins, and you end up with one good looking bullet-proof race shifter. Optional Forward and Reverse shift pattern gate plates are available for most popular 2, 3 and 4-speed transmissions. This model Pro Stick comes out of the box ready for action for most popular 3-speed transmissions, includes a 5-foot Super Duty shift cable, brackets, levers, hardware and detailed instructions for an easy installation. Be sure to check out all the optional Magnum Grip side grip plates including the one and two button 12-volt momentary switches or any of the other accessories we offer for the Pro Stick in the Shifter Accessories section. Notes: AOD requires installation kit #40496, AODE & 4R70W requires installation kit #40504, E40D & 4R100 requires installation kit #40505, 2004R & 700R4 require gate plate #80712, 4L60E – 4L85E equipped with PRNDL switch requires cable bracket kit #70499 and gate plate #80712. Overall Dimensions – 8.25L x 2.92W x 9.25H

Product Features:

• All One-Handed
• Reverse Lockout Meets NHRA And IHRA Requirements
• Mount Directly To Floor/Chassis/Or w/Quick Release
• Ultimate For Powerglide Applications
• Lightweight Brushed Alum. Cover
• Cover Removed Quickly and Easily
• Includes 5 Ft. Super Duty Race Cable
• Quick Change Plate Design

All the quality and performance you’ve come to expect from MSD is now available in black. Our customers have requested black parts for their builds so we’ve answered with the addition of several black distributor caps and cap and rotor kits. The black parts are built to the exact specifications of the traditional MSD red components. If you’re looking to change up the look under the hood of your street machine, off-road rig or race car; check out the complete line of MSD black components.

Product Features:

• Injection Molded From DuPont Rynite Material
• Extreme strength; high dielectric properties
• Designed with performance in mind
• High quality; voltage insulating material
• Brass terminals
• Black in color

Product Features:

• Capable of 300 plus horsepower when matched with the Edelbrock Performer Power Package
• 1.90 in. intake valves are for use with stock pistons
• Exhaust valve is 1.60 in.
• 60cc combustion with 170cc intake port
• Flat Tappet Camshaft Type

These valve covers are constructed of a heavy gauge steel that will also help to prevent leaks around sealing flanges. Sold as a pair.

Product Features:

• Fits Ford small block
• Chrome plated steel construction
• Sold as a pair
• Chrome Plated

A higher than stock stall speed as delivered by a B&M Converter will provide several advantages. The high stall converter allows the engine to launch the car at a higher RPM where more torque is available and increased strength.

Product Features:

• New Precision Pump Drive Tube
• Pressure Tested
• Fully Balanced
• Needle Thrust Bearing
• New Thrust Washer
• Washer Between Turbine and Cover

Transpak – Ford, Lincoln, Mercury – 1980 to 1992 AOD (excludes 1992 and later with electronic shift). Recalibrate your automatic transmission for optimum performance. Select the mode that best suits your application. Improves transmission life. Transmission removal not required. The next step up from the Shift Improver Kit is the Transpak. It has all the features in the Shift Improver Kit plus it provides additional driver manual control (GM TH-400, 350, Ford C-6 and Chrysler Torqueflite only). Most stock automatic transmissions won’t downshift into low gear above 15 mph, and automatically upshift at a predetermined speed no matter what gear you’re in. With the Transpak, you can downshift at any speed, and you can hold the transmission in first gear to any speed that you want! This is an asset when you’ve got a modified engine, and you want additional RPMs, or you’re towing a trailer or driving heavy loads downhill. Stage 1 Heavy Duty – For street rods, normal passenger vehicles or other heavy duty use. Firmer shift feel but not harsh. Improves transmission performance and life dramatically without loss of comfort. Normal automatic operation when in Drive. Stage 2 Hi-Performance Street – For full performance street use. Essentially the same as Heavy Duty mode except shift is much quicker. Retain full automatic features and standard shift points with selector in Drive.

Product Features:

• Recalibrate Auto. Transmission
• Optimum Performance
• Select Your App. Mode
• Improves Transmission Life
• Trans. Removal Not Required
• Downshift At Any Speed
• Great For Trailer Towing
• For Heavy Loads Driving Downhill