Ford Galaxie 500 Air Intakes
Top Ford Galaxie 500 Air Intakes Categories
We carry over 193 Air Intakes in inventory for the Ford Galaxie 500. If you’re looking for aftermarket Air Intakes for your Ford Galaxie 500, check out all these categories:
Essential Ford Galaxie 500 Air Intakes
Edelbrock – Standard Main Jet Carburetor Metering Jet #12456 Size .055 (Pair) (Part No.12456)
from
$14.99
The Edelbrock 94 #12456 Carburetor Jets .056″ Intended for tuning the Edelbrock 94 carburetor, but will also fit original Holly 94’s and its later variations. Jets sold in pairs.
Product Features:
See More
Product Features:
- 56 Maximum Jet Size
- 0.055 in. Orifice Diameter
- 1/14-32 in. Thread Size
- Standard Main Jet Type
- Set of 2
Wells Vehicle Electronics – Carburetor Repair Kit (Part No.2G1768)
from
$25.99
Product Features:
See More
- Application matched component to ensure the system can be returned to like new condition.
- Product constructed to meet all design and operating characteristics as intended by the vehicle manufacturer.
Holley – SysteMAX; Intake Manifold Gasket (Part No.108-80)
from
$56.99
Kormetal gasket used between the SysteMax II Ford 5.0 liter upper and lower manifolds.
Product Features:
See More
Product Features:
- SysteMAX II Upper/Lower Manifold
Wells Vehicle Electronics – Carburetor Choke Pull-Off (Part No.1C1007)
from
$12.99
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Felpro – Air Cleaner Mounting Gasket (Part No.60032)
from
$3.49
Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.
Product Features:
See More
Product Features:
- Meets or exceeds all original equipment specifications
- Application specific design to ensure a perfect fit
- Engineered for the sealing repair environment
- Unsurpassed quality you can trust
- Validated for fit, form, and function
Edelbrock – Carburetor Accelerator Pump Diaphragm #12400 30cc (Part No.12400)
from
$13.99
Product Features:
See More
- The Edelbrock Accelerator Pump Diaphragm 30cc Gasoline #12400 for 4150 Carburetors Proper installation is the responsibility of the installer.
- Improper installation will void your warranty and may result in poor performance and engine or vehicle damage
Edelbrock – Carburetor Throttle Cable Bracket #1495 For Ford 429/460 Big-Block (Part No.1495)
from
$26.99Product Features:
- Repositions Stock Throttle Cable Bracket
- Use With PN[1483]
- Use w/Stock Throttle Cable Bracket
- For Fords w/Cable Activated Throttles
- Fords w/Automatic Transmission Kickdown Rod
Edelbrock – RPM Air-Gap Small Block Ford 302 Black Intake Manifold (Part No.75213)
from
$605.99
Edelbrock part #75213 RPM Air-Gap intake manifold is designed for street 289 302-347 c.i.d. Ford V8’s. The RPM Air-Gap incorporates the same race-winning technology that’s been used on our Victor Series competition intakes for decades. The Air-Gap design
Product Features:
See More
Product Features:
- 1500-6500 RPM Range
- Dual Plane Type-4150 Style Flange
- 4.3 in. Front Height, 4.9 in. Center Height, 5.5 in. Rear Height
- Black Powder Coated Finish
- Made In The USA
Edelbrock – Carburetor Gasket Kit #12370 Fits 2300, 4150, 4160, 4165, And Some 4500 Carbs (Part No.12370)
from
$20.99
The Edelbrock #12370 comes with fuel bowl and metering block gaskets. The Edelbrock #12370 is designed to be used with Holley 2300, 4150, 4160, 4165, and some 4500 carburetors.
Product Features:
See More
Product Features:
- Nitrile Rubber Material
- Metering Block, Fuel Bowl Type
- Set of 4
- Fits Holley® 2300, 4150, 4160, 4165, And Some 4500 Carburetors
- Made In The USA
Edelbrock – Fuel Bowl Inverted Flare Fuel Inlet Fitting #12415 (Part No.12415)
from
$22.99
Edelbrock part #12415 Fuel Bowl Inverted Flare Fitting is a 3/8″ inverted flare fuel inlet fitting. The fitting is designed for use with Holley 2300, 4150, 4150HP and 4160 (center hung floats only), 4500, 4500HP and Rochester Quadrajet applications up to
Product Features:
See More
Product Features:
- Brass Material
- 3/8 in. Single Barb
- 7/8-20 in. Male End
- 5/8-18 in. Female Flare
- With 3/8 in. Tube
Edelbrock – Carburetor Gasket Kit #12380 Fits 4150 And 4160 Carburetors (Part No.12380)
from
$18.99
Product Features:
See More
- The Edelbrock #12380 Metering Block gasket is made of black nitrile material and will ensure a leak-free seal from your Carb to the metering block.
- The Edelbrock #12380 Metering Block gasket will fit 4150 &4160 Carburetors.
- These will not work with accelerator pump transfer tubes.
Edelbrock – Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange) (Part No.1221)
from
$46.99
Stamped from 18 gauge steel. Triple-chrome plated. High quality finish. Great looks. Works with all 5.152 inch carburetors. Base knock-outs for use with crankcase ventilation.
Product Features:
See More
Product Features:
- Stamped From 18-Gauge Steel
- Triple-Chrome Plated
- High-Quality Finish
- Great Looks
- Works With All 5.125 in. Carbs
- Base Knock-Outs For Use w/Crankcase Ventilation
Wells Vehicle Electronics – Carburetor Choke Thermostat (Part No.2C1220)
from
$11.49
The carburetor is a device used to mix air and vaporized fuel for combustion in old school engine applications. The last year for carburetors in motor vehicles used on the road in the U.S. is listed as 1994. The carburetor was typically a down draft style device where oxygen was drawn from the top of the carburetor pulled in by the engine vacuum through a venturi style opening, just above the venturi were jets, or metered openings where fuel was pulled from a bowl of fuel within the carburetor.
Product Features:
See More
Product Features:
- Application matched components ensure carburetor can be returned to like new condition.
Edelbrock – Performer Carburetor Calibration Kit #1487 for #1406 Carburetors (Part No.1487)
from
$66.99
Product Features:
See More
- Customize Carburetor Calibration and Performance
- Owners Manual has Assembly Help
- Includes Metering Rod Retaining Spring
- Includes Metering Rods
- Includes Metering Jets
- Includes Step-Up Springs
Mr. Gasket – Intake Manifold Bolts (Part No.958G)
from
$22.99
These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 5/16 inch-18 x 2 inch bolts & washers
Product Features:
See More
Product Features:
- Hex Head
- Zinc Plated
- Ideal For Minimal Space
- 12-Point Head And Flange
- Zinc Plated For Protection
Holley – Carburetor – 750 CFM Street Hp Mech Sec (Part No.0-82751)
from
$799.99
The Street HP uses the best features from Holley’s race Bred 4150 HP carbs, but tamed for street and light competition use. The contoured main body from the 4150 HP has a tumble polished shiny finish. The metering system includes a timed spark port for a vacuum advance distributor and is calibrated for a hot street and strip engine setup for outstanding throttle response and drivability. A street HP base plate is used so there are plenty of vacuum ports for power brakes, PCV, etc.
Product Features:
See More
Product Features:
- Vibratory Polished For Good Looks
- Optimized Calibration For Outstanding Drivability
- Contoured Venturi Inlet Balances Airflow For Increased hp
- Screw In Air Bleeds For Precision Tuning Capabilities
- Four Corner Idle For Precise Idle Control
- Mechanical Secondaries For Awesome Tire Turning Performance
- Dual Accelerator Pumps For Add. Fuel Under Initial Acceleration
- Dual Feed Fuel Inlets For Constant High Volume Fuel Delivery
- Intended For Lightweight Vehicles w/Man/Auto Trans
- 100% Wet Flow Tested By Holley Technicians
- Arrives Ready To Run
Edelbrock – Carb Needle & Seat Hardware Kit #12600 FOR Holley Carb w/ Center Hung Fuel Bowl (Part No.12600)
from
$14.99
The Edelbrock #12605 Hardware Kit will fit carburetors with center hung fuel bowls and can be used as replacements or performance upgrades. Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 45
Product Features:
See More
Product Features:
- Fits Holley® Carburetors With Center Hung Fuel Bowl
- Includes Adjusting Nut
- Includes Locking Screw
- Includes O-Ring
- Includes Washers
Holley – REPLACEMENT MAIN BODY KIT FOR 0-80457S (Part No.134-342)
from
$195.99
REPLACEMENT MAIN BODY KIT FOR 0-80457S
Edelbrock – Adjustable Carburetor Needle and Seat #12602 Size .097 With Viton Tip (Part No.12602)
from
$18.99
Product Features:
See More
- The Edelbrock #12602 Adjustable Inlet Needle and Seat assembly will fit Carburetors with center hung fuel bowls and can be used as replacements or performance upgrades.
- Kit includes one locking screw, two gaskets and one O-ring. For use with Holley 2300, 4150, 4160, 4165, 4175 and 4500 Series, Quick Fuel 4500, Professional Series and Q-Series, as well as various Demon Carburetors.
Dorman – Help – Rubber Expansion Plug 1-5/8 In. – Size Range 1-5/8 In. – 1-3/4 In. (Part No.10232)
from
$5.99
Our Engine Intake Manifold Expansion Plug is conveniently designed as a direct replacement for stripped plugs. A proper fit is ensured, every time.
Product Features:
See More
Product Features:
- Manufactured from high quality materials for a long service life
- Torque values listed on parts (where applicable)
- Easy to install
- Constructed to strict engineering quality standards
Edelbrock – Throttle Lever #1483 For Ford 1968 And Later, Gold Iridited Finish (Part No.1483)
from
$40.99
Product Features:
See More
- Converts Throttle Lever on Carb for Proper Use
- For Edelbrock Performer Series Carburetors Only
- Also Accepts Cruise Control
- Use with Appropriate Throttle Cable Plate
Edelbrock – Carburetor Accelerator Pump Cam Kit #12403 for 2300, 4150, And 4160 Carburetors (Part No.12403)
from
$43.99
The Edelbrock #12403 Accelerator Pump Cam Kit Assortment Package of 8. These accelerator pump cams will have different shapes and profiles, allowing you to fine tune the accelerator pump’s performance to the engine’s requirements. Cam “lift” will directly
Product Features:
See More
Product Features:
- Multi-Color
- Plastic Material
- Fits Holley® 2300, 4150, And 4160 Carburetors
- Set of 8
- Made In The USA
Edelbrock – Carb Power Valve Block-Off Plug #12624 For Demon, Holley, & Quick Fuel Carbs (Part No.12624)
from
$13.99
The Edelbrock 94 Carburetor power valve block off #12624 is a great way to fine tune your vintage series carburetor. These Edelbrock Power valve Block Off’s will fit Edelbrock Vintage Series 94 carburetors as well as original Holley 94’s and its later var
Product Features:
See More
Product Features:
- Fits Any Demon®, Holley®, And Quick Fuel® Carburetors
- Includes Gasket
- 1/2 in. x 28 Power Valve Thread
- For Applications That Prefer To Run Carbs Without The Power Valves
- Made In The USA
Edelbrock – Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs (Part No.12412)
from
$26.99
The Edelbrock #12412 Vacuum Secondary Spring Kit includes 7 springs that will fit on Holley 4150, 4150HP, 4160 series and various Demon Carburetors.
Product Features:
See More
Product Features:
- Steel Material
- For Holley® 4150, 4150HP, 4160; Demon King, Mighty, Race, Road, Sea, Speed; Barry Grant Claw
- Includes Lightest To Heavy
- Set of 7
- Made in The USA
Ford Galaxie 500 Air Intakes Categories
Helping You Find the Right Air Intakes for Your Ford Galaxie 500
You love your Galaxie 500. So we’ve made it easier than ever to help you find Ford Galaxie 500 Air Intakes in our online catalog. Our inventory holds 193 aftermarket and OEM Air Intakes for your Ford Galaxie 500, ranging from $2.99 to $2,126.99.
We offer parts from 8 brands trusted to make quality Air Intakes for your Ford Galaxie 500. Before you buy, take some time to read through customer reviews. We currently have 8,660 reviews of Ford Galaxie 500 Air Intakes from previous customers. Some of the top rated parts include Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet with 4.4 stars and Street Carbs with 3.4 stars.
Find your Galaxie 500 Air Intakes here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Ford Galaxie 500 part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Air Intakes Brands for Your Ford Galaxie 500
Our inventory holds Air Intakes for your Ford Galaxie 500 from 8 trusted brands. You’ll find OEM and aftermarket parts from brands like FELPRO, Edelbrock, and Holley, all of which can keep that Ford happy.
We have Weiand parts available for your Ford Galaxie 500 in categories like Intake Manifold Parts. Some of the top-rated Weiand parts in these categories are:
Top-Rated Edelbrock Air Intakes
Leading Edelbrock Air Intakes
We carry Edelbrock brand parts for your Ford Galaxie 500 across several catalog categories, including Carburetor Parts and Air Cleaner Parts. Some of our most reviewed Edelbrock parts include:
from
$428.99
(55)
Performer 1406 Carburetor: 600 CFM, 4 Barrel, Square Bore, Electric Choke Inlet
Carburetors
from
$46.99
(19)
Pro-Flo Chrome 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
from
$394.99
(10)
Performer 1405 Carburetor: 600 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
Carburetors
FAQs for Ford Galaxie 500 Air Intakes
What are the most purchased Air Intakes for the Ford Galaxie 500?
Out of 193 Air Intakes for the Ford Galaxie 500, the most popular in our inventory are:
from
$50.99
(9)
Pro-Flo Black 14" Round Air Cleaner with 3" Paper Element (Deep Flange)
Air Cleaner Assemblies
What are the top-rated Ford Galaxie 500 Air Intakes?
Top-rated Air Intakes for your Ford Galaxie 500 based on customer reviews/ratings are:
from
$474.99
(7)
Performer 1407 Carburetor: 750 CFM, 4 Barrel, Square Bore, Manual Choke Inlet
“Easy install, had it installed in less then 30 mins on my 70 camaro 350 after my holley failed. It started right up only adjustment i had to do was tu”
from
$26.99
(6)
Carburetor Vacuum Secondary Spring Kit #12412 Includes 7 Springs
“Holding up well so far”
