Ford F-350 Ignition Electronic Parts

Relays are electrical switches used to convert a small electrical load into a circuit capable of handling a high amperage load. Computers and small switches are not designed to carry the higher amperage requirement of a circuit that may have an electric motor, solenoid, or high amperage lighting fixture. Within a relay are contacts that are controlled with electromagnetism, when the circuit switch commands the device on or off, magnetism will pull or release the contact arm closing or opening the contacts within the relay that carry the voltage.

“The MSD Flying Magnet Crank Trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This “”flying magnet”” design produces accurate trigger signals and the non-magnetic pick-up cannot be falsely triggered. Each Flying Magnet Crank Trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The CNC-machined aluminum bracket securely holds the pick-up in place and is slotted to provide a wide range of timing adjustments. Spacers are included so you can mount the bracket on engines with standard motor mounts or engines with a .25″” motor plate. These systems will trigger MSD 6, 7, and 8 Series Ignitions and all MSD Timing Accessories.”

“Holley’s EFI Crank Trigger Kit is engineered to provide an accurate crank speed & position signal to Holley EFI systems in the most-demanding, high horsepower, racing applications. Crank position is measured every 10 degrees as opposed to every 45 degrees for a standard 4-Magnet, MSD “”style”” Crank trigger. It is designed for use on SBF applications using a standard ATI or Fluidamper “”style”” balancer up to 7-1/4″” in diameter.”

“Most crank triggers have a wheel, with steel studs sticking out, bolted to the harmonic balancer. As the crankshaft turns, the studs pass by a stationary magnetic pick-up, triggering the ignition. This pick-up can be triggered by other bolts, debris, or even vibrations which will cause a loss of power or engine damage. The MSD Flying Magnet Crank Trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This “”flying magnet”” design produces accurate trigger signals and the non-magnetic pick-up cannot be falsely triggered.”

For a long time, racers have known that one of the best things to do to an engine to improve performance is to stabilize the ignition timing. The MSD Flying Magnet Crank Trigger system does exactly that by using four magnets embedded in an aluminum wheel. Although similar in appearance to other crank triggers, the MSD Flying Magnet design works on a different principle. Most crank triggers have a wheel, with steel studs sticking out, bolted to the harmonic balancer. As the crankshaft turns, the studs pass by a stationary magnetic pick-up, triggering the ignition. This pick-up can be triggered by other bolts, debris, or even vibrations which will cause a loss of power or engine damage.

CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

The only parts recommended by Ford Motor Company for Ford, Lincoln and Mercury vehicles.

CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

PerTronix 9FO-1820 Module replacement (only) (one module) for 9FO-182 Ignitor II Kit.

This high performance ignition module provides your plugs with more spark over the stock module. The solid state electronics provide high coil out put and superior reliability. The Dwell control circuit ensures, long consistent coil charging. The current control circuit protects against coil over heating. This module fits most Ford Thick Film Ignition systems. 1983 thru 1996.

The ignition control module controls the primary side of the ignition coil and in some applications is able to control ignition timing. The ignition control module receives a signal from a pick-up coil located in the distributor or from the engine control module (ECM) to identify piston location.

CARQUEST Ignition Modules are built by an ignition systems manufacturer with expertise in the entire vehicle spark system.

The original Ignitor module is ideal for restorations. Ignitor Module Kits are extremely easy to install and fit into your original distributor to maintain your stock look. No additional ignition box is required keeping a clean look under the hood. Ignitors are available for most distributors that came with mechanical breaker points and will cover AUTOMOTIVE, MARINE, INDUSTRIAL and AGRICULTURE applications

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.

The distributor is just one piece of this type of ignition system which is typically driven by the engine’s camshaft. The distributor is the device that delivers the ignition spark to the spark plugs at a precise time, and spark timing is critical. Any wear or component out of place in this type of system will result in failure. Within the distributor and mounted to it are many individual pieces which allow the distributor and system to be maintained and repaired to keep it in top working order.