from

$477.99

Our DynaForce starter is designed to crank over the highest compression engines on a hot day in Death Valley. Not that too many race cars are sitting in Death Valley, but it’s good to know that you have the oomph to make it happen. The DynaForce starter features all new components beginning with a three horsepower motor. This power is used to crank over the reduced 4.4:1 gear set to deliver great torque to the engine’s ring gear to get the engine turning. The downsized housing clears most headers and oil pans, but just in case, we made the billet mount so it can be clocked in different positions to help in tight applications. The assembly is powder coated MSD red and will stay looking good, even though it’s underneath your car.

Product Features:

3/4″ Depth and can be used on 157 and 164 Tooth Flywheels
Downsized design helps clearance issues w/oil pans and exhaust
Ball bearing supported armature and pinion gear
3 Hp Motor Provides Power For High Compression Engines
Gear reduction of 4.4:1 improves torque for great cranking
Downsized design helps clearance issues
Mount can be clocked to assist in mounting

from

$212.99

Flexplt: Bb Ford 70-97 (164T)

from

$620.99

MSD’s Ready-to-Run Ford distributors are the perfect upgrade for bulky Duraspark systems or ancient breaker point models. All you need to do is drop it in the engine, connect three wires and fire the engine. Each distributor features an ignition module that produces a powerful inductive spark to improve combustion of the fuel mixture resulting in quick starts, smooth idle and increased performance. The billet aluminum housings of these distributors are 5/8 In. smaller in diameter to accommodate induction setups and tight engine compartments. A maintenance-free magnetic pick-up is responsible for triggering the high voltage sparks while a sealed ball bearing guides an oversized shaft. Beneath the bolt down cap and MSD race rotor you’ll find MSD’s accurate mechanical advance assembly. Different advance springs and stop bushings are supplied so you can easily tune a curve to match your needs. Plus, there is a vacuum advance canister to increase economy on long drives.

Product Features:

Simple And Clean Installation w/Only Three Wires To Connect
Built-in module produces a 7.5 amp single spark through high rpm
Easy-to-adjust mech. advance w/supplied springs and stop bushings
Vacuum advance canister for improved economy (can be locked out)
CNC machined billet aluminum housing and billet aluminum base
Housing Is 5/8 in. Smaller In Diameter Than Stock Ford Distr.
Maintenance-free magnetic pickup and precision reluctor
Polished steel shaft is guided by a sealed ball bearing

from

$52.99

Designed to allow additional adjustment of the clutch fork height to eliminate clutch release problems when installing a high performance clutch. Recommended for use with Lakewood safety bell housings. Available for most GM, Ford, and Mopar applications. Adjustable dowel pins correct for improper register bore alignment of bell housing.

Product Features:

Allows Additional Adjustment
Eliminates Clutch Release Problems

from

$46.99

Brake Bleeder Screws

from

$50.99

Fel-Pro gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Rigid core, molded silicone rubber gaskets provide for ease of installation, and are great for on-again/off-again situations (like setting valve lash).
Features high-tech silicone material for long life, a solid steel core for strength and durability, and stainless steel compression limiters to prevent
Not intended for use in emission controlled vehicles.

from

$77.99

The B&M Shift Improver kit, is the easiest way to get the performance you want out of your transmission. A few simple modifications and your transmission will shift fast, firm and live longer.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$65.99

MSD Ignition is a company built on Customer Satisfaction and Service. That is why all of MSD products go through regimented test procedures before they are ever packaged and shipped. MSD stands behind its products for one full year after purchase

Product Features:

Rotor phasing can be adjusted.
Ideal When Atomic TBI Is Controlling The Timing

from

$9.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Saves Your Tie Rods
Lasts Longer
Looks Great

from

$29.99

Mr. Gasket High Performance Thermostats are designed to resist large variations of coolant pressure at high RPM (revolutions per minute). This allows them to fully open at correct temperature consistently regardless of engine RPM. The design also provides the high flow that engines operated a higher RPM need. This thermostat also features a copper/brass construction to further resist corrosion. Mr. Gasket High Performance / High Flow Thermostats are suitable for street, drag race, or oval track applications.

Product Features:

Opens At 180 Degrees
Designed to Resist Large Variations of Coolant Pressure at High RPM
Fully Opens at Correct Temperature Consistently Regardless of Engine RPM
For High Performance Street, Drag Race, and Oval Track
Copper & Brass Construction – Resists Corrosion
High Flow

from

$119.99

The best all-round choice for vehicles with leaf or coil springs. Properly loads rear wheels to prevent over-reaction and wheel hop.

Product Features:

Excellent Weight Transfer
Lets Front End Down Quickly
Maximum Traction
Makes Vehicle Safer
Easier Control At End Of Track
Better Overall Stability

from

$48.99

This Mr. Gasket Rear Main Seal is made from silicone to allow the seal to handle extreme engine oil temperature. It also provides for an upgrade for that leaky rope style seal and is a direct replacement for a rubber main seal. It’s also injection molded for a precise fit.

Product Features:

Repairs That Leaky Rear Main Sail
Silicone Rubber to Withstand Extreme Engine Oil Temperatures
Upgrade for Rope Seal Equipped Cars or Direct Replacement for Rubber Main Seal
Injection Molded for Precise Fit

from

$599.99

For a long time, racers have known that one of the best things to do to an engine to improve its performance is to stabilize the ignition timing. The MSD flying magnet crank trigger system does exactly that by using magnets embedded in an aluminum wheel. The MSD flying magnet crank trigger uses four magnets secured in the aluminum trigger wheel that pass by a stationary non-magnetic pick-up to trigger the ignition. This flying magnet design produces accurate trigger signals and the non-magnetic pick-up cannot be false triggered. Each flying magnet crank trigger includes a two-piece mounting bracket for the non-magnetic pick-up that in most cases will work on either the passenger side or driver’s side of the engine (the SB Chrysler and SB Ford brackets mount on only one side). The adjustable bracket provides a wide range of timing adjustment and spacers are included. These systems will trigger MSD 6, 7, 8 and 10 series ignitions and all MSD timing accessories.

Product Features:

Absolutely the most accurate way to trigger the ignition
The non-magnetic pickup cannot be false triggered.
Powerful magnets are embedded in a billet aluminum trigger wheel.
Incl. brackets/mounting hardware to fit a variety of engines

from

$1087.99

50 state street legal aluminum cylinder head. Out-of-the-box bolt-on performance. Intake valves are used for stock pistons.

Product Features:

50-State Street Legal Aluminum Cylinder Head
Out-of-the-Box Bolt-On Performance
Intake Valves Are For Use w/Stock Pistons

from

$387.99

Product Features:

Designed for Optimum Torque and Acceleration
Maximum Performance From Idle through Mid-Range
Matched to Edelbrock Performer Intakes
Includes Hydraulic Lifters and Assembly Lube
Major Improvement in Throttle Response and Torque
Use For Daily Drivers/Trucks/Vans/RVs/4x4s
Take The Guesswork Out Of Camshaft Selection

from

$414.99

Burnished aluminum. GM/MAC- style throttle linkage. Electric choke installed from factory. Easy tuning with 2 piece design. Smooth secondary transition. Both timed for full vacuum ports. Includes PCV outlet.

from

$59.99

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-temperature steel core/graphite faced exhaust material
Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
Conforms to and seals minor surface irregularities
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
For use with SVO square port cylinder heads
Easy Removal For Disassembly

from

$199.99

Universal street and strip. For street-driven vehicles with breaker point ignition or OE electronic ignition. Delivers optimum performance when used with these Mallory ignition products: UNILITE (R) distributor with a HYFIRE (R) capacitive discharge ignition, magnetic breaker less distributor with a HYFIRE (R) capacitive discharge ignition, or dual point distributor. Effective to approximately 6500 RPM when used with a point type distributor (depending on engine combination). Effective to approximately 8000 RPM when used with a Mallory HYFIRE electronic ignition control (depending on engine combination).

Product Features:

Glass Filled Polyester Case
Longer Spark Duration
Increased Performance
No Energy Loss Due To Arcing
Includes Brass Contact Terminal

from

$85.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets

from

$485.99

Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods.

Product Features:

Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
Best with aftermarket converters and more rear gear.
Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.

from

$31.99

Product Features:

Heavy Duty Cap and Rotor Kit
With Brass Inserts

from

$257.99

Single Outer Valve Springs from COMP Cams allow you to build the perfect spring assembly for your application. The valve spring creation process is far more involved than most people realize. Selecting the right metal stock and creating the best design is not done by chance. COMP Cams has developed a process that creates the highest quality valve spring available. The result is a product that meets and exceeds the expectations of today’s engine builders and racers.

Product Features:

Seat pressure: 115 lbs. @ 1.700″, Open Pressure: 284 lbs. @ 1.200″
O.D.: 1.437″, I.D.: 1.039″
Single valve springs with damper
Approximately .510″ max lift at recommended installed height

from

$376.99

Edelbrock #88433 Water Pump Ford 1970-78 302 & 1970-87 351w v8 black ideal to prevent overheating in street rods and street machines, as well as in tow rigs and motorhomes. Using state-of-the-art racing technology, Edelbrock has designed these “super cool

Product Features:

Standard Impeller Rotation
0.625 in. Pilot Shaft
0.750 in. Ball/Ball Bearing
5.70 in. Block To Hub Height
Black Finish

from

$52.99

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

PROPRIETARY COATING – Nonstick anti-friction coating seals small surface imperfections
NO RETORQUE DESIGN – Steel core helps eliminate the need for retorquing head bolts
SUPERIOR SEAL – Precise embossed Printoseal sealing beads at all vital areas to eliminate leak paths
STRONG AND DURABLE – Features graphite or reinforced fiber facing material and steel armor for strength and durability
DESIGNED FOR IMPERFECT SEALING SURFACES – Engineered and manufactured specifically for the repair environment to help seal imperfect sealing surfaces