Ford E-250 Econoline Ignition Coils and Boots

Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.

Product Features:

• Direct performance replacement for Ford TFI coil
• 85:1 turns ratio
• Lower Primary Resistance Produces High Voltage Output
• Works w/Stock Ignition As Well As MSD Ignitions
• CARB E.O. Approved

Motorcraft ignition coils offer value without compromising quality. They are the right fit for Ford and Lincoln vehicles.

Product Features:

• Helps ensure proper engine performance, maximize fuel economy, minimize both tailpipe emissions and RFI electronic interference
• Helps avoid spark plug failure, drivability complaints, pre-ignition and detonation
• Insulation provides multiple coats on the primary and secondary windings to ensure no internal arcing
• Radio-Frequency Interference (RFI) Suppression
• Magnets hold strength for the coil to maintain proper energy output
• Steel used in the lamination stack to ensure a consistent magnetic field needed to develop the required voltage
• Coil Housing is engineered to withstand extremes in temperature without cracking

As the innovator and leader in stick coil technology DENSO has conducted superior testing and inspection processes to insure the highest quality ignition coil. Don’t be fooled by imitations – look for the DENSO name to be sure you’re getting the best.

Product Features:

• First Time Fit
• Built to DENSO Original Equipment Standards

Carquest Premium ignition coils meet or exceed original equipment (OE) specifications and are developed by top OE/OES manufacturers to ensure superior performance. All of our Carquest Premium ignition coils are developed by IATF 16949 certified manufacturers for consistent durability and long-lasting performance. These ignition coils use high-quality components and will utilize optimized designs on applications where the OE ignition coil had frequent failures. We require stringent testing standards to ensure proper fit and performance for each application and stand behind our Carquest Premium ignition coils with an industry-leading warranty. Carquest Premium ignition coils are part of our Carquest Vehicle Solutions, which is a full line of engine management and electronics products that help control ignition, fuel delivery and emission systems. Carquest Vehicle Solutions are OE-quality parts designed, engineered and tested by world-class manufacturers to ensure a reliable and long-lasting repair.

Product Features:

• Computer-Aided Design (CAD), laser scanning and 3D printing – utilizing Fused Deposition Modeling (FDM) and Stereolithography (SLA) – in the part design process ensures speed-to-market and a precise fit guaranteed.
• 100% pure copper precision-wound windings increase coil life and ensure reliability and maximum coil output when needed.
• Highly conductive aluminum alloy secondary terminal guarantees secondary coil terminals will not oxidize (rust), will provide excellent conductivity, extended coil life and will not cause excessive stress on the primary control circuit.
• 100% thermo-shock and vibration tested to ensure superior performance in extreme conditions.
• 100% end-of-line tested to ensure confidence and product reliability, every time.

The only parts recommended by Ford Motor Company for Ford, Lincoln and Mercury vehicles. Motorcraft and Ford Parts are used throughout Ford vehicles in a variety of applications that help ensure the proper build quality, integrity and long-lasting performance of every Ford car or truck. Motorcraft and Ford Parts are manufactured from first quality materials chosen specifically for maximum performance and application suitability. As with all Motorcraft and Ford Parts, any innovations or improvements developed since the vehicle’s manufacture are included in these after market replacement parts, ensuring the most current technology and performance.

Product Features:

• These coils provide the exact spark timing that helps maximize the engine and emissions performance
• RFI suppression helps minimize electronic noise through a Ford patented spring assembly inside the coil boot
• Engineered to help withstand temperature extremes
• Internal insulation displacement connection is helps make high-reliability internal connections
• Interior insulation helps ensure no internal arcing
• Right fit for each application; helps provide ease of installation and removal
• High grade silicone rubber boot materials do not degrade or stick, aiding in environmental and dielectric sealing
• Housings engineered to help resist cracking in the most extreme conditions
• Ford-patented iron core lamination stack integrates rare earth magnets in the flux circuit to help deliver consistent high energy required for output

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

• Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
• Identical OE end caps are designed to “click” into place for easy installation and a secure fit
• Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

• Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
• Identical OE end caps are designed to “click” into place for easy installation and a secure fit
• Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

DENSO First Time Fit COP boot sets are identical in form fit color and performance to the factory-installed boots. Every part of each COP boot set construction meets or exceeds OE/OES standards.

Product Features:

• OE design ensures a tight boot seal that protects against moisture intrusion
• High temperature resistant material provides greater protection against thermal overload
• Stainless steel internal spring with resistor to suppress RFI and deliver maximum voltage to the plug
• Engineered to the specifications used by the original vehicle manufacturer for an exact fit

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

• Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
• Identical OE end caps are designed to “click” into place for easy installation and a secure fit
• Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

NGK Coil on Plug Boots are built to stringent OEM tolerances, combining original equipment fit, design and outstanding durability. NGK Coil on Plug Boots are manufactured using only premium silicone and always include any required internal springs and ferrite resistors for superior performance and RFI noise suppression. Bridging the important link between ignition coil and spark plug, COP boots should always be replaced with NGK Coil on Plug Boots at the time as changing spark plugs to prevent ignition problems such as flashover.

Product Features:

• PREMIUM GRADE SILICONE: Designed to withstand harsh environments
• OEM MATCHED: Includes all required internal springs and ferrite resistors for superior performance and RFI noise suppression

Product Features:

• SAEJ2031 Class E cable resist heat (428 Deg. F), cold (-104 Deg. F), electrical interference, abrasion and oil.
• Stainless steel magnetic winding delivers maximum voltage to the spark plug for more powerful, and longer spark resulting in optimum engine performance while reducing the chance for misfire, and eliminating radio static.
• 100% Pure silicone external insulation resists oil penetration, for lifetime protection against wire set failure.
• EPDM inner insulation stops power-robbing voltage leaks.
• With Magnetic-impregnated Kevlar internal conductors – durable and break resistant
• Engineered to meet OEM tolerances using variable pitch wire winding, creating better resistance to electric magnetic interference (E.M.I resistance).
• Excellent interference suppression and consistent performance
• Easy lock terminals for more convenient installation.
• Thick silicon outer jacket for excellent heat resistance. Insulating EPDM based compound inner jacket helps minimize voltage drop and enhance durability.
• Broad coverage available for most vehicles on the road today
• Include grease pack to ensure easy installation and removal

The MSD 8.5mm super conductor wire is the performance wire. Engineered from the inside out, the 8.5 offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference. In a single 12 inch length of super conductor wire there is only 40 – 50 ohms of resistance. That is the lowest resistance of any helically wound wire. To accomplish this, we use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss in spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight in fact, that there is over 40 feet of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) or choke. This choke, or suppression capability, keeps the EMI inside the wire where it cannot interfere with other electronics on your vehicle. The outer sleeve that surrounds the conductor assembly is just as impressive. A proprietary blend of silicone and synthetic material produce a sleeve that is highly resistant to high heat as well as abrasion and tears. Available in universal kits and bulk lengths.

Product Features:

• Bolt-on Performance
• Custom Fit For Make And Model Listed
• Wires Are Pre-Cut To Exact Specifications

DENSO First Time Fit Ignition Wire Sets are identical in form fit color and performance to the factory-installed wire sets. Every part of each wire sets construction meets or exceeds OE/OES standards.

Product Features:

• Each wire is pre-cut to exact length so the wire set is ready to install right out of the box
• Identical OE end caps are designed to “click” into place for easy installation and a secure fit
• Strong connections – through a patented process, the terminals are attached to provide an extremely strong connection, ensuring the cable and boot will not separate during removal and installation

Motorcraft Plug Wires are Manufactured of premium-quality materials to strict Ford Engineering standards. High-Dielectric Insulation helps maintain and control voltage delivery while reducing Radio Frequency Interference. EPDM/Silicone wire jacket, spark plug & coil/ distributor insulators help protect against oil and high temperatures. Optimized wire lengths help minimize part numbers while still providing proper fit. Designed and Tested to Stringent Ford Standards.

Product Features:

• Backed by Motorcraft’s Service Parts Warranty
• Designed for long life – key life durability testing (equivalent to 10 years/150,000 miles) is conducted in addition to on-vehicle durability testing.
• Optimized wire lengths help minimize part numbers while still providing proper fit.
• Wires are optimum lengths for easy installation.
• EPDM/Silicone wire jacket, spark plug AND coil / distributor insulators help protect against oil and high temperatures.
• Motorcraft ignition components help prevent false check engine lights.

With more than double the energy output of a stock coil, E3s new 2 Valve coil features a stainless steel spark plug contact ring with a ferrite lug to suppress EMI/ RFI noise. Designed to work with the factory DIS electronic controls as well as high performance aftermarket ignition systems, the resistance and inductance values have been optimized to increase output at high RPM levels. Our high temperature epoxy resists shock and vibration while providing excellent thermal conductivity ensuring extra long life. Additionally, the spark plug boots are molded in a special high temperature 550 degree F silicone compound. Fits the 1997 to 2013 2 Valve Ford engines.

Product Features:

• Designed to work with factory DIS electronic ignition systems
• High temperature epoxy provides excellent thermal conductivity and long life
• Stainless steel spark plug contact ring and optimized resistance and inductance provide high output at higher RPM levels
• Fits 1997-2013 2-Valve Ford engines
• Crosses to MSD 8248

This ignition coil connector is designed to match the appearance and function of the original hardware on specified applications. Made of quality materials, it is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this ignition coil connector matches the appearance and function of the factory hardware on specified applications
• Ideal solution – this connector is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our ignition coils use 100% pure copper windings in the primary and secondary bobbins to improve durability and provide higher resistance to internal shorts and dielectric breakdown
• Our premium ignition coils consist of a special blended formula for the best performance, longest life and better heat dissipation
• A full E-Lam core of silicon steel and solid brass high voltage terminals protects against corrosion. Our ignition coils are built for maximum output voltage
• Primary and Secondary windings feature enamel magnet wire for the highest temperature rating in the aftermarket

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our ignition coils use 100% pure copper windings in the primary and secondary bobbins to improve durability and provide higher resistance to internal shorts and dielectric breakdown
• Our premium ignition coils consist of a special blended formula for the best performance, longest life and better heat dissipation
• A full E-Lam core of silicon steel and solid brass high voltage terminals protects against corrosion. Our ignition coils are built for maximum output voltage
• Primary and Secondary windings feature enamel magnet wire for the highest temperature rating in the aftermarket
• BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Product Features:

• Premium quality materials for longer service life
• Sealed connections (where applicable) to prevent environmental corrosion and performance issues
• Global coverage for import and/or domestic applications
• OE specified wire gauge to ensure a reliable electrical connection
• Designed to meet or exceed OE specifications in form, fit and function

BWD is an aftermarket leader, providing a premium line of engine management products. BWD manufactures and distributes high technology critical components for late model domestic and import vehicles. BWD is constantly evolving to give customers the competitive edge they need to compete in today’s ever-changing marketplace.

Product Features:

• Our knock sensors are designed to respond to knock frequencies up to 1000 Hz accommodating shifts in engine knock frequency making it a more flexible sensor responding to correct engine knock over a broad range of vehicle conditions
• Manufacturing processes include an automated data acquisition system to continuously monitor the sensor output to ensure that it responds with appropriate voltage output at the specified frequency range
• All units are 100% tested using an accelerometer vibration test to ensure trouble-free operation
• Featuring the broadest sensor coverage in the market, we meet the service professionals needs with the highest quality product every time he opens the box
• BWD is a global manufacturer of original equipment ignition products, complete quality control is maintained through the manufacturing process from componentry to finished product