Ford Bronco II Drivetrains

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

• Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

Dana 28 & Dana 30 pinion gear Thrust washer. Also fits AMC Model 35 with 1.560″ side gear bore only.

Product Features:

• Pinion gear thrust washer for Dana Spicer 25, 27 and 30

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• For U-Joints 354, 369 & 437G
• Contains two 1.59″ bolt center clamps and four 1/4-28 x 5/8″ cap screws

Product Features:

• Ford 7.5″, 8.8″ Ring Gear Bolt

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific, providing unsurpassed quality for a seal you can trust
• Validated for fit, form, and function
• Engineered for the sealing repair environment
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

Yukon flange yoke for Ford 7.5″ passenger and truck (4.3″ OD). All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits Ford 7.5″
• 28 spline
• Round companion flange
• 4.3″ O.D.

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits Ford 7.5″
• Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

Pinion seal for 7.5″, 8.8″, and 9.75″ Ford, and also 1985-’86 9″ Ford.Yukon Mighty seal.

Product Features:

• Pinion seal
• Fits Ford 7.5″, 8.8″ and some 9.75″
• 2.785″ O.D.

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

This spindle nut retainer is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this spindle nut retainer matches the fit and function of the factory part on specified years, makes and models
• Ideal solution – this retainer is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool
• Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Designed to repair damaged, grooved or worn shafts
• Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
• Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
• Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
• Easy to install with removable flange and installation tool
• Installation tool reduces sleeve distortion and allows for installation without removal from the shaft

Value-priced bearing meets all cataloged application requirements.

Product Features:

• Brand may vary by location

Bearing race driver. No return.

Product Features:

• Bearing race driver
• Fits M88010 race
• All steel construction

Product Features:

• Spring kit for Dana Spicer 28, AMC Model 35 IFS, Dana Spicer 44 IFS and Dana Spicer 50 IFS
• Allows for installation of positraction or locker

The Powertrax Lock-Right ultra-strength alloy locker’s straight-line performance is equal to a solid spool, but automatically unlocks in turns. Best suited for extreme off-road to severe on-road use, Powertrax Lock Right lockers replace the spider gears in your open differential carrier using basic tools and without affecting your ring and pinion settings. The whole job can be done in your driveway in a couple of hours, pin included! Powertrax Grip-Lok, Lock-Right Lockers and No-Slip Traction Systems automatically provide 100% traction on-demand, under the toughest circumstances. The Powertrax Grip-Pro and Grip-LS performance limited slips offer smooth dependable torque transfer and traction for the best of both worlds!The Powertrax® Lock-Right Locker provides outstanding traction for off-road machines and race vehicles. Powertrax No-Slip Traction Systems deliver excellent performance to street-driven cars and trucks.

Powertrax® lockers range from the original, Lock-Right for serious straight-line performance, to the No-Slip traction system for street-able vehicles.

Powertrax® offers three levels of GRIP locking differentials, ranging from the clutch-type GRIP LS with a forged steel case, the gear-driven GRIP PRO and finally the GRIP LOK for extreme traction.

Powertrax® = Extreme Traction Systems!

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Going manual requires Warn spindle nut conversion kits. These kits allow you to replace your Warn factory automatic locking hubs with manual hubs and are available to correspond with your specific Chevy, GMC or Ford application. Warn spindle nut kits include inside bearing nuts, outside bearing nuts and lock washers. Go for increased durability and fuel economy; go Warn spindle nut conversion kits.

Product Features:

• Manual Hub Spindle Nut Kit

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• Designed for ease of installation
• Includes necessary hardware
• Designed for superior performance
• Designed for ultimate strength
• Increased tolerance for a performance fit
• Meets deflection parameters

Ford 7.5″ C/clip, TracLoc & standard Open.

Product Features:

• c-clip for Ford 7.5″
• Fits standard open and Trac Loc applications
• Not compatible with Auburn Gear positraction

Yukon 1541H alloy replacement rear axle for Dana 60, 70, and 80, 35 spline. (40″ to 43.5″) Full float axle (8×3.96″ ). Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a full-floating axle.

Product Features:

• 35 spline
• 8 x 3.96″ bolt pattern
• Cut to length design fits 40″-43.5″ applications
• Fits Dana Spicer 60, 70 and 80

Spindle nut for Dana 28, without pin, ’92 & down. This replaces Spicer part number 40080.

Product Features:

• Spindle nut
• Fits 1992 and down Dana Spicer 28

This spindle nut is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this spindle nut matches the fit and function of the factory part on specified years, makes and models
• Ideal solution – this nut is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:

• Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications
• Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion
• 100% new – this transfer case motor is entirely new, not remanufactured like competitors
• Quality assured – vehicle-specific application has been validation tested to ensure quality

CARDONE Remanufactured Transfer Case Motors are designed to meet or exceed O.E. performance. Reverse engineering provides insight into how and why the unit originally failed, allowing our engineers to identify and correct original design weaknesses. Each unit is 100% computer tested at three points during the remanufacturing process to ensure reliability. CARDONE is committed to getting your vehicle back to peak performance with our direct-replacement transfer case motors.

Product Features:

• All motors are 100% torque tested to ensure strength for proper gear engagement.
• Each unit is 100% computer tested at 3 points during the remanufacturing process for guaranteed performance.
• Every motor is assembled with the precise amount of lubricant to ensure quiet operation and long life.
• Motor magnets are 100% recharged for superior performance and reliability.
• Transfer case motor sensors are 100% replaced with new, O.E.-quality sensors for superior performance and long product life.