Chevrolet Silverado 2500 HD Differentials

Adjuster lock bolt for left hand case half of 7.2″ and 9.25″ GM IFS.

Product Features:

• Side adjuster lock bolt
• Fits GM 7.2″ IFS and 9.25″ IFS

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

• Fits GM 9.25″ IFS
• Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

Differential Cover G

Product Features:

• Spider gear kit
• Fits GM 10.5″ 14 bolt truck open differential
• Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

11.5 GM spanner adjuster nut.

Product Features:

• Side adjuster
• Fits GM 11.5″

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

• Fits GM and Chrysler 11.5″
• Included are a pinion seal, crush sleeve , complete shim kit, marking compound and brush.

14T pinion gear Thrust washer.

Product Features:

• Pinion gear thrust washer
• Fits GM 10.5″ 14 bolt truck

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

• Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
• Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
• Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
• Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

14T GM pinion shim kit.

Product Features:

• Pinion depth shims for GM 10.5″ 14 bolt truck

Bearing race driver for rear GM 9.5″, 9.25″ IFS, and Ford 9″ HD. (TK HM804810). No return.

Product Features:

• Bearing race driver
• Fits HM804810 race
• All steel construction

Yukon 1480 Lifetime Series U/Joint. 4.188″ snap ring span, 1.375″ cap diameter. Outside snap ring.

Product Features:

• Clutch kit
• Fits GM 10.5″ 14 bolt truck with Eaton positraction
• Carbon fiber clutches

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

11.5″ GM standard Open side gear Thrust washer.

Product Features:

• Side gear thrust washer
• Fits GM 11.5″

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Product Features:

• KIT SHIM SIDE 9.5″ GM

SHAFT SEAL

aFe Power’s new front differential cover brings performance engineering to the protection of your axle’s differential. This differential cover is constructed out of durable cast aluminum with reinforced ribs for maximum strength. This cover comes with all necessary hardware for easy installation. Pro Series differential covers include an oil level sight glass and magnetic deep reach fill plug. This cover is finished with black powder-coating and machined fins for a distinctive look. Increased Oil Capacity: This cover has an increased oil capacity over stock for better performance over a longer duration. Built-in Internal/External Fins: Built-in internal and external fins transfer heat from the oil to the outside air for maximum cooling. Magnetic Plugs: This system incorporates a magnetic drain and deep reach fill plug to capture loose particles for maximum protection. Calibration Plug: Calibration plug set to the factory oil level to eliminate overfilling. Oil Level Sight Glass: A pre-installed oil level sight glass allows quick and easy oil inspection. When it comes to engineering for power, performance, protection and value, aFe Power is the only choice.

Product Features:

• Durable Cast Aluminum
• Magnetic Drain and Fill Plugs Capture Loose Particles
• Calibration Plug Set to Factory Fill Level Eliminates Overfilling
• Oil Level Sight Glass for Quick/Easy Inspection

Product Features:

• NUT PINION – 14 BOLT

This differential pinion shaft lock bolt is designed to match the fit and function of the original part on specified vehicles. Made of quality materials, it is engineered for reliable performance.

Product Features:

• Direct replacement – this differential pinion shaft lock bolt matches the fit and function of the factory part on specified years, makes and models.
• Ideal solution – this bolt is a reliable replacement for an original part that is missing or has failed due to fatigue
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Yukon yoke for GM 10.5″ 14 bolt truck, 1410, strap style. 4.188″ snap ring span, 1.188″ cap diameter. Outside snap ring. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 10.5″ 14 bolt truck
• 30 spline
• 1410 u-joint size
• 4.188″ snap ring span
• 1.188″ cap diameter
• Outside snap ring design
• Strap style

Valvoline ULV is a full synthetic, ultra low viscosity transmission fluid specifically engineered for high speed automatic transmissions. Formulated to meet the performance requirements of the latest 9 & 10 speed transmission designs, including the Ford/GM 10R80 found in select Ford F-150 and Raptor trucks.

Product Features:

• Formulated with premium synthetic base oils to achieve low viscosity and minimize deposits
• Provides excellent thermal and oxidation performance
• Durable friction modifiers help prevent shudder
• Advanced anti-wear technology to better prevent gear wear

Pilot bearing for 10.5″ 14 bolt truck, 2.050″ O.D.

Product Features:

• Pilot bearing
• Fits GM 10.5″ 14 bolt truck
• 2.050″ O.D.

Product Features:

• Brand may vary by location