Chevrolet R10 Performance and Racing Products

These universal in-line fuel pumps are intended for fuel Injection systems. They are designed to work in-line, not inside the tank, so installation is a snap. They’re all rated for continuous duty service and have been tested up to 2,500 hours.

Product Features:

• Flows 43 gph At 15 PSI
• Draws 3.5 Amps At 15 PSI
• Will Feed Up To 400 Horsepower Throttle Body EFI Unit
• OE Proven Design
• Lightweight and Compact
• 3/8 in. Barbed Fittings Included

Billet aluminum handle with flexible braded steel tube mounts to the firewall. 29-3/4 inch long.

Product Features:

• Braided Stainless Steel
• Firewall Mounting
• Includes Oil Fill Tube

Product Features:

• Fuel Economy From The Engine
• Leak Test For Max Performance
• Mandrel-Formed Power Plenum
• Leakproof O-Ringed Port Seals
• Include All Mounting Hardware

HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) Application: HoleShot 2400 for GM 1993 to 1996 TH700R4 (30 spline) and 1984 to 1993 4L60E (30 spline) A higher than stock stall speed as delivered by the Holeshot converter will provide several advantages and benefits in vehicles with modified engines. Many modifications, particularly big cams, tend to reduce low end power and torque. The high stall converter allows the engine to launch the car at higher rpm where more torque is available. The Holeshot is generally a very good choice for the typical street machine that is looking for better launch capability and more strength. Street rods with modified engines will also benefit from a Holeshot converter. If your vehicle is equipped with a plate type nitrous system, you will need a Nitrous Holeshot!! Stall speed listings are based on engines producing 230lb. ft. of torque at 2,500 rpm. More torque at 2,500 rpm will give you more stall speed, less torque at 2,500 rpm will give you less stall speed than the stall speed ratings indicated. Furnace brazed impeller. New precision steel alloy pump drive tube. New heavy duty needle bearing between stator and impeller (not a thrust washer). Needle bearing between stator and turbine. Furnace brazed turbine. Dual pattern drive lugs on some GM Holeshots. New turbine hub. New springs and rollers in stator.

Product Features:

• Furnace Brazed Impeller
• Steel Alloy Pump Drive Tube
• Heavy Duty Needle Bearing
• Between Stator and Turbine
• Furnace Brazed Turbine
• New Turbine Hub
• New Springs/Rollers In Stator

Power Train

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

Chrome plated steel valve covers with original equipment height and internal baffle. Features one breather/oil fill cap opening per valve cover. Sold as a pair. Hardware and gaskets sold separately.

Product Features:

• Chrome plated steel construction
• Center bolt design with ribbed top
• Has two openings in one cover & one opening in the other
• Includes rubber grommets and chrome oil filler cap
• Sold as a pair
• Has Ribs On The Top Of Each One

Mr. Gasket Performance Intake Gaskets are manufactured from cellulose/nitrile composition gasket material. This is a low density material that conforms well to irregular surfaces and has very good crush resistance at high flange pressures. They provide excellent sealing and durability as the material is designed for sealing gasoline, oils, water and coolant in applications up to 350 degrees Fahrenheit. While die-cut for an excellent fit, they can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track.

Product Features:

• Manufactured from cellulose/nitrile composition gasket material
• Provides excellent sealing and durability
• Die-cut for an excellent fit
• Can be trimmed if necessary for modified port applications
• For OE replacement, high performance street, drag race and oval track use

Rotor assembly for a GM HEI late model with external coil cap Chevy V8 cap-a-dapt. The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

• Resist Carbon Tracking
• Max Voltage Transfer
• Molded From Insulated Material

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Performance exhaust header gasket consisting of a high-density fiber facing material attached to both sides of a perforated steel core.
• Resists blowout and burnout from high-temperature exhaust and is far stronger than basic paper gaskets.
• Anti-stick coating permits motion without damaging the gasket and makes it easier to remove the gasket for future engine service.
• Slotted bolt holes allow for easier header installation.
• Not intended for use in emission controlled vehicles.

Spectre’s Valve Cover Hold Downs feature high quality steel construction with a triple chrome-plated finish. Manufactured for an optimum fit, this product’s hex heads include a decorative O-ring cap for a customizable appearance to suit your needs. Sold 4 per package, these studs are intended to fit standard height Chevy Center bolt valve covers.

Product Features:

• 4 bolts included in each package
• Allen head includes decorative O-ring cap
• Triple chrome-plated finish
• Fits standard height Chevy Center bolt valve covers

Mr. Gasket cam locking plates feature a steel retainer plate designed to secure the cam gear bolts from coming loose and backing out, preventing costly engine damage. Retainer plate fits under bolt heads allowing tabs to be bent against hex head flats creating a secure positive lock.

Product Features:

• Black oxide finished steel
• Includes (3) grade 5 bolts & locking plate
• Fits Chevrolet Small and Big Block without OE roller cam
• Tabs bend up around bolt head to secure

This chrome plated breather, embossed with a Mr. Gasket logo, is perfect for race car vacuum balance systems and OEM use. It fits any 1 1/4 inch diameter hole. It has metal baffle/foam element with 1 inch outer diameter neck and 5/8 inch outer diameter breather tube.

Product Features:

• Internally battled
• High-porosity filter
• Ideal for high performance
• Includes rubber grommet

Fits Chevy small block 265-400 CID, Chevy big block 396-454 CID, & 90 degree Chevy V6. The Starter Motor Heat Shield is built with heat-resistant material sandwiched between two aluminum plates. The shield protects the starter from heat buildup from the exhaust system, especially important when using headers.

Product Features:

• Designed to prevent starter overheat due to extreme exhaust temperature
• Heat resistant material sandwiched between 2 aluminum plates
• Protects Starter From High Temperatures
• Made Of 2 Sheets Of Aluminum Heat Resistant Center
• Natural Finish

MSD Ignition control are easy to install, but we also offer several direct plug-in harnesses for late model vehicles! The harnesses plug directly into your factory coil and harness then four color coded wires plug into the corresponding wires of the MSD.

Product Features:

• Plug-In Harness w/Color Coded Wires
• No Cutting Or Splicing
• Quick Easy Installation
• Provides A Direct Plug-In Installation
• When Adding An MSD Ignition Control

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Fel-Pro Performance Gaskets deliver reliable sealing under grueling racing conditions

Product Features:

• Steel core gasket construction
• Exclusive design permits significantly faster gasket installation while eliminating potential sealing leak paths.
• Not intended for use in emission controlled vehicles.

Spectre’s High Performance Replacement Air Filters are engineered to outperform ordinary paper filters by providing increased air flow for improved performance. Manufactured using high quality materials including pre-dyed synthetic media, urethane, and steel mesh, this performance air filter is factory pre-oiled and ready to use. Use a Spectre Accucharge cleaning and re-oiling kit, part number HPR4820, to maintain your filter’s condition.

Product Features:

• Designed to be superior to stock paper filters
• Comes pre-oiled
• Designed for an easy installation with OE fit
• Made with pre-dyed media for lasting color

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

• Ideal For Tight Spaces
• Serrations Prevent Loosening
• Flange Distributes Pressure
• Zinc Plated Bolts
• Grade 5 Material
• Easy Installation

Product Features:

• Service Part
• Makes Connections Quick And Easy

These High Energy Die Cast Aluminum Roller Rocker Arms for Chevy V8 265-400 applications are perfect for street and moderate race use. With a 3/8″ stud diameter and 1.5 ratio, the die cast, larger-than-stock body of the rocker arms is made of aluminum for superior strength with light overall weight. High Energy Die Cast Aluminum Roller Rocker Arms from COMP Cams are an affordable option that feature a die cast, aluminum body with a needle bearing fulcrum and roller tip. Designed to be stiffer and more durable, these cost effective rocker arms are capable of providing added valve lift while withstanding the rigors of a performance application. Their specially engineered fulcrum and roller tip create far less friction than sliding factory models to lower oil temperatures, thus improving both response and horsepower. Snap rings are used to hold the trunion and bearings locked in place..

Product Features:

• Cost effective aluminum construction provides superior strength to weight ratio
• Needle bearing fulcrum and roller tip reduce friction and lower oil temperatures for improved response and horsepower
• Durable design increases valve lift while withstanding the rigors of moderate race use
• Die-formed aluminum body is larger than stock, and may require modifications to stock valve covers for clearance.

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1955-85 GM small block (internally balanced) V8 engines along with 4.3L V6 engines. Also fits 1990 and earlier GM big block (internally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions.

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

This Mr. Gasket Deluxe Engine Bolt Kit includes chrome plated grade 5 hex head fasteners with AN type washers for the following: Intake Manifold, Timing Cover, Oil Pan, Fuel Pump, Water Neck, Long Water Pump and Headers. The AN washers have no exposed shoulder which offers a professional appearance.

Product Features:

• Chrome plated
• Grade 5
• AN washers with no exposed shoulder for a professional appearance

This is a high quality bolt set that is made of grade 8 steel and will meet your requirements for a quality bolt set, this set will work on original equipment, high performance street, drag or circle track applications.

Product Features:

• Has A Zinc Dichromate Finish
• Made Of High Quality Grade 8 Steel
• Has A Tall Hex Head To Prevent Wrench Slipping Off
• Extra Thick Parallel Ground Washer
• Washer Provides More Accurate And Uniform Torque