Chevrolet G20 Performance and Racing Products

Mechanical fuel pump made from heavy duty construction for continuous high RPM operation. Fuel body casting can be rotated to accommodate various plumbing situations. Fuel pressure regulator is not required.

Product Features:

• High Output Fuel Flow
• Flows 130 gph Free Flow
• Shutoff Pressure Pre-Set From 7.5 To 9 PSI
• Fuel Pressure Regulator Required Recommend P/N 12-704
• Heavy Duty Construction For Continuous High rpm Operation
• Redesigned High Flow Valves Ensure Adequate Fuel Delivery
• Fuel Body Casting Can Be Rotated For Plumbing Situations
• Inlet And Outlet Tapped For 3/8 in. NPT

The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:

• Provides Crisp Shifts
• On Any Stock Automatic Transmission
• Eliminates Soft/Sluggish Shift
• Eliminates Shift Overlap
• Eliminate Clutch and Band Wear
• Improves Transmission Life
• Transmission Removal Not Required

VALVE SEALS, O-RING 11/32″ 1 ST

The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.

Product Features:

• Fits stock distributor
• High quality material
• Brass terminals
• High dielectric properties

Dowel pins are precision machined and case hardened for accurate head alignment. Two per set. 5/16 inch x 5/8 inch

Product Features:

• Precision Machined
• Case Hardened
• Give Accurate Alignment
• 2 Per Set

Product Features:

• Re-Engineered to Handle High Horsepower
• Outlasts Rubber
• Virtually Indestructible

Product Features:

• For use on Small Block Chevys with 4150 series carb (side mounting) and the Victor Ram base manifold #7075 only
• Made of aluminum with a natural finish
• Hardened washers must be used with intake bolts
• Single Plane
• Made In The USA

New chromed steel pulleys are a replacement for originals and are designed as matched sets to assure correct alignment of the drive belts. They are highly polished then chrome plated. Crankshaft Pulley = 7.30 inch diameter Water Pump Pulley = 6.30 inch diameter

Product Features:

• Chrome plated steel
• Designed as matched assemblies

K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers, and is protected by the K&N 1-Year Limited Warranty.

Product Features:

• Designed to allow high flow rates and a consistent flow of oil to your engine
• Pleated synthetic-blend filtration media removes most harmful contaminants
• Fast and easy Wrench-Off removal using the welded one-inch hex nut
• High capacity to withstand the service intervals recommended by vehicle manufacturers
• Heavy-duty canister for outstanding durability
• Laboratory tested to ensure excellent capacity, efficiency, and mechanical strength
• Designed to operate with all synthetic, conventional, and blended motor oils
• 1-Year Limited Warranty

These new coils mount directly in place of the factory coils and accept the factory connectors. Spark energy is increased thanks to improved materials and windings that were spec’d by MSD engineering.

Product Features:

• Replacement Coil For GM Dual Connector Coil
• Improved Turns Ratio
• Lower Primary Resistance
• Bolt-In replacement coil
• Produce More Output Voltage
• Smooth Idle

As performance levels increase, an O.E. style flexplate just won’t cut it and a stronger option is a necessity to prevent transmission and/or converter failure. B&M has you covered with our high performance flexplate designed for 1965-90 Chevrolet big block 454ci (externally balanced) V8 engines with two piece rear main seal. Features include high tensile strength steel construction to resist elongation and cracking, dual bolt pattern 10.75 or 11.5 inch converter mounting locations, 168 tooth ring gear with double-sided welds for added strength and comes with SFI 29.1 safety certification insuring the ultimate in safety and performance. The assembly is then Zinc plated and treated with a Chromate Conversion Coating for added corrosion resistance and durability. B&M SFI approved flexplates are ideal for extreme duty race applications as well as street cars, tow vehicles or other vehicles needing the added protection and toughness that B&M has been delivering since 1953. Compatible with Powerglide, TH350, TH400 and TH700R4 automatic transmissions

Product Features:

• NHRA/IHRA Legal For All Classes
• Includes SFI Certification Sticker
• Ideal For Street Applications
• To Extreme Duty Racing
• To High RPM Use

Edge molded rubber water outlet gasket is reusable, great for engines that require regular disassembling for maintenance. Incorporates solid aluminum carrier for strength and rigidity. Can be used with OE replacement or aftermarket chrome water outlets. Requires no gasket sealer.

Product Features:

• Edge Molded Rubber Water Outlet Gasket Is Reusable
• Requires No Gasket Sealer
• Solid Aluminum Carrier For Strength/rigidity
• Reusable – Ideal for Engines That Are Frequently Taken Apart & Reassembled

Parts and accessories for Flame-Thrower Billet Distributors offer unmatched quality and accommodate the performance levels your distributor was engineered for.

Product Features:

• Rotor for Flame-Thrower cast distributors
• Replacement premium rotor with brass contact.

When a high pressure fuel pump is run with a steel roller cam core, the stock fuel pump pushrod is not compatible with the steel core. You can damage an expensive roller cam as a result of wear at the fuel pump lobe. COMP Cams offers several fuel pump pushrods for various applications.

Product Features:

• Lightweight tubing with bronze tip for steel cams
• 5.75″ Length
• Eliminates wear at the fuel pump lobe often caused by a stock fuel pump pushrod

The street fire spark plug wires feature a low resistance conductor that’s wrapped in a sleek and durable black sleeve. The terminals are covered in black boots that protect the conductor from engine heat to ensure spark delivery.

Product Features:

• Helically wound conductor suppresses electro and radio noise
• Kevlar core combination for great strength and durability
• Heavy Duty Terminals For Secure Connection
• 8mm silicone and synthetic jacket resists heat and abrasion
• 500 Ohms/ft. Resistance For Improved Spark Delivery And Power
• Silicone Boots Protect Against High Exhaust Temps

Starting on the inside, a 0.500 In. oversized steel shaft spins in a sealed ball bearing and sintered bushing for long endurance and accurate spark delivery throughout the entire RPM range. Mounted on top of the shaft is an easy-to-adjust chromoly mechanical advance assembly. Different advance springs and stop bushings are supplied so you can choose from 24 curves. A maintenance-free magnetic pick-up provides accurate trigger signals to your MSD Ignition control. A precision-manufactured reluctor that is connected to the shaft is responsible for triggering the pick-up. The distributor is topped off with a high quality black cap and race rotor.

Product Features:

• CNC machined billet aluminum housing and billet aluminum base
• Will not accept a vacuum advance canister
• Must Be Used w/An MSD Ignition Control
• O-ring seals can be installed for oil press. control (Mods only)
• Supplied w/Socket Style Distributor Cap And Rotor
• Special oil tract improves lubrication to the dist./cam gear
• Nylon pads ensure smooth operation of the advance weights
• Advance weight pins are staked and tig welded to the plate

A B&M transmission in a box! Transform your automatic transmission into a full-tilt B&M performer! This is our ultimate transmission kit – it comes complete with full instructions on how to assemble your transmission to B&M specifications.

Product Features:

• High Perf. Friction Materials
• Complete Overhaul Gasket Set
• Modification Components
• Replacement Valves
• Replacement Springs
• Drain Plug Kit Included

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

• Maintains Better Alignment While Driving
• Full Floating and Non Binding
• Fits Into the Remaining Stock Control Arms

High Energy Hydraulic Flat Lifter Chevrolet SBC, BBC, and 194-292/200-262 V6.

With the introduction of our 20 Amp extreme HEI module, we needed an HEI cap and rotor that could withstand the high output. The answer was to mold our own HEI cap, rotor and coil cover. The cap and rotor will fit our HEI Pro-Billet distributor, PN 8365.

Product Features:

• Designed w/performance in mind
• High quality; voltage insulating material
• Stainless Terminals
• High dielectric properties

Made of chrome plated steel. Smooth top with original equipment height and internal baffle. Features one breather/oil filler cap opening per valve cover. Hardware and gaskets sold separately.

Product Features:

• Fits 1960-1986 Chevy 262-400 Small Block
• OEM height, short-style covers
• Chrome plated steel construction
• Perimeter style bolt pattern
• Features 1 breather/oil fill cap opening per valve cover
• Sold as a pair

It’s easy to overlook the small details. For engine builders focused on the larger components like camshafts, cylinder heads and pistons, small parts are often forgotten until the final stages of engine assembly. COMP Cams Engine Finishing Kits include those often missing parts like woodruff keys, cylinder head alignment dowels, cam bolts, and timing cover and oil pump dowel pins that are so crucial to properly assembling your engine.

Product Features:

• Includes parts such as woodruff keys, cylinder head alignment dowels, cam bolts, timing cover and oil pump dowel pins
• Available for various engine applications

Energy Suspension performance bump stops help cushion a collapsing suspension, preventing bottoming-out and expensive vehicle damage. Hyper-Flex performance polyurethane bump stops for control arms, traction bars, leaf springs, etc. are guaranteed to last longer and operate more efficiently than original rubber stops. The smaller, general purpose bullet shaped snubber is ideal for control arms. the low profile button head is for use when clearance is limited. Our large competition race style bump stops smooth out compression better and have a large reinforced metal plate welded to the mounting plate and molded-in. Each style is specially designed for a perfect and custom fit and each style has it’s own durometer, hardness, characteristics. Energy’s wide selection of bump stops are available in red or black color.

Product Features:

• Made of Superior Hyper-Flex+ Material
• Helps Prevent Damage to Control Arm

Spectre’s Intake Bolt and Washer Set is engineered to provide premium quality hardware for Chevrolet 265-400 and Chrysler 273-440 small block engines. Measuring 3/8 inch-16 by 1 inch, these grade 5 bolts feature a corrosion resistant zinc-plated finish and hex heads to ensure easy installation. This kit includes 12 bolts and washers.

Product Features:

• Designed for Chevrolet 265-400 and Chrysler 273-440 small block engines
• 3/8 inch-16 by 1 inch bolts
• Kit includes 12 bolts and washers
• Manufactured from high quality steel
• Bolts feature hex heads

These grade 5 hex head bolts are brite zinc plated for protection and appearance. Hardened flat washers provide uniform torque & prevent galling on aluminum manifolds. Includes twelve (12) 3/8 inch-16 x 1 inch bolts & washers

Product Features:

• Zinc plated to resist corrosion and provide a clean professional appearance
• Made from Grade 5 steel for strength and durability
• Flat washers provide uniform clamp load and prevent galling on aluminum intake manifolds
• Allen (socket) Head
• Zinc Plated For Protection