from

$9.99

With advanced load-carrying capacity and compact design, tapered roller bearings are used in wheel bearings, transmissions, differentials, transfer cases and other miscellanous applications. FAG manufacturers over 100 million tapered roller bearings annually.

Product Features:

High-precision and High-quality components used in all KITs
Coverage of classic and new high-tech solutions for the best system coverage

from

$48.99

10.5″ GM 14 bolt truck pinion nut. 1 1/2″ socket, 15/16″ x 16 thread.

Product Features:

Pinion nut for GM 10.5″ 14 bolt truck
15/16″ x 16 thread
1.5″ socket

from

$12.99

10.5″ GM 14 bolt truck crush sleeve, 1989 & newer. Approx 0.920″ long.

Product Features:

Crush sleeve for 1989 and up GM 10.5″ 14 bolt truck
0.920″ tall

from

$8.29

Fel-Pro® gaskets are specifically designed for the repair environment to deliver a reliable seal on even the most troublesome applications. Designed for imperfect sealing surfaces and manufactured with proprietary materials, you can count on Fel-Pro for innovative sealing solutions for the real-world repair environment.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Engineered for the sealing repair environment
Validated for fit, form and function
Unsurpassed quality you can trust

from

$994.99

Differential

from

$561.99

Yukon spider gear set for GM 9.5″ Gura Drip posi. This kit does not include clutches. This kit fits Yukon Dura Grip ONLY.

Product Features:

Spider gear kit
Fits GM 9.5″ with Dura Grip positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$295.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits Dana Spicer 60 rear
Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.

from

$533.99

Product Features:

Each LuK GearBOX contains all the OE quality bearings needed for a professional transmission repair
LuK Differential Bearing Kits are designed to meet or exceed OEM requirements. This will ensure customer satisfaction.
LuK Differential Bearing Kits contain the bearings and seals needed to complete the job.
LuK Differential Bearing Kits include wear parts such as seals, O-rings, shaft sealing rings, support bearings and spare parts where necessary for eliminating the specific cause of failure.

from

$16.99

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust.

Product Features:

Meets or exceeds all original equipment specifications
Application specific design to ensure a perfect fit
Unsurpassed quality you can trust
Validated for fit, form and function
Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

from

$9.99

Product Features:

Inner oil slinger for Dana Spicer 60

from

$40.99

Manufactured with premium-grade steel, National taper bearing cones feature crowned raceways and rollers to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways and rollers for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on

from

$832.99

Yukon replacement positraction internals for Dana 60 and 70 with 35 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit includes clutches. All components come with a one year warranty against manufacturing defects.

Product Features:

Clutch kit
Fit Dana Spicer 60 Powr Lok positraction with 35 spline axles
Smooth design
Includes two side gears, four pinion gears, cross pin shafts and side gear thrust washers.

from

$215.99

Bearing race driver for rear GM 9.5″, 9.25″ IFS, and Ford 9″ HD. (TK HM804810). No return.

Product Features:

Bearing race driver
Fits HM804810 race
All steel construction

from

$156.99

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

Cross pin shaft
Fits Dana Spicer 60 and 70
Powr Lok positraction only

from

$508.99

Yukon 1541H alloy right hand Full float rear axle for GM 14T with a length of 36-3/8″ inches and 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects.

Product Features:

30 spline
8 lug
36 3/8″ long
Fits GM 10.5″ 14 bolt truck

from

$2.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$529.99

Yukon replacement standard open carrier case for Dana 80, 3.73 & down, (incl ABS) 35 & 37 spline.

Product Features:

Standard open carrier case
Fits Dana Spicer 80
3.73 and down ratio only
Does not include spider gears

from

$8.99

Product Features:

Clutch guide for Chrysler 9.25″, Dana Spicer 44 and Dana Spicer 60
For Trac Loc positraction applications only

from

$14.99

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.6″, 7.6″ IFS, 8.5″, 8.6″ & 9.5″.

Product Features:

Pinion nut washer for GM 7.2″ IFS, 7.5″, 7.625″, 7.6″ IFS, 8.5″, 8.6″ and 9.5″.

from

$231.99

Product Features:

DANA-70 R/P 5.86 STD .625″ OFFSET

from

$53.99

Product Features:

STRONG AND DURABLE – Controlled heat treatment process for strength and durability
PREMIUM MATERIALS – Precision manufactured using premium-grade steel for durability and performance
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
Professional technicians know they can depend on National

from

$41.99

Royal Purple Motor Oil is a specially formulated multi viscocity oil for use in gasoline and diesel engines of all types from cars and trucks to SUVs, motorcycles and boats. Royal Purple(R) Motor Oil with Synerlec(R) additive technology reduces friction, which results in a 1-3 percent increase in horsepower, lowers operating temperatures, provides superior corrosion protection, improves fuel economy, reduces emissions and extends oil life. A.P.I. Certified.

Product Features:

Better wear protection
Increased fuel efficiency
Better protection of the expensive catalytic emission system
Improved compatibility with fuels containing ethanol
Superior corrosion protection
Meets ILSAC GF-5 and Dexos1 performance requirements

from

$5.99

Product Features:

Pinion nut washer
Fits Dana Spicer 80

from

$1010.00

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:

Fits Dana Spicer 80
11.25″ ring gear diameter
37 spline pinion
12 ring gear bolts
3.31 ratio

from

$15.49

Manufactured with premium-grade steel, National taper bearing cups feature crowned raceways to ensure even load distribution.

Product Features:

PREMIUM MATERIALS – Precision manufactured using premium-grade steel for outstanding durability and performance
SMOOTH ROTATION – Crowned raceways for even load distribution
OE-STYLE DESIGN – Engineered to meet OE specifications
COMPREHENSIVE COVERAGE – Industry-leading coverage for domestic and import applications
RIGOROUS TESTING – Comprehensive testing throughout design and development processes by National engineers for quality you can count on