from

$8.99

Standard open side gear thrust washer for 9.5″ GM.

Product Features:

Side gear thrust washer
Fits GM 9.5″

from

$205.99

Product Features:

GM10.5″ 14 BOLT OPEN EMPTY CASE 4:56 & UP

from

$306.99

Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses Timken bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:

Fits 1997 and down GM 9.5″
Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.

from

$13.99

14T cover gasket.

Product Features:

Cover gasket
Fits GM 10.5″ 14 bolt truck

from

$29.99

9.5″ GM differential carrier Supershim kit.

Product Features:

Super carrier shim kit for GM 9.5″
Interlocking design makes installation much easier

from

$819.99

Hard use and poor lubrication can wear out a limited-slip differential. Restore original performance with this replacement differential carrier assembly that includes all-new spider gears, differential pins, clutches and carrier housing.

Product Features:

Direct replacement – this 30 spline limited-slip differential carrier fits in place of this vehicle’s original equipment carrier
100% new – this differential carrier uses all-new components, including spider gears, diff pin, pre-load spring pack and clutch pack
Ready to install – this differential carrier is shipped pre-assembled and ready to install
Ideal upgrade – can be used to upgrade from open differential to limited-slip in an existing differential

from

$36.99

Yukon Minimum installation kits are a low cost solution for gear changes in newer vehicles where the bearings can be reused. This kit uses all high quality components to ensure a smooth set up. kit includes a pinion seal, crush sleeve (if applicable), complete shim kit, marking compound and brush.

Product Features:

Fits GM 7.2″ IFS
Included are a pinion seal, crush sleeve, complete shim kit, marking compound and brush.

from

$221.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$26.99

9.5 Standard Open Pinion gear Thrust Washer.

Product Features:

Pinion gear thrust washer
Fits GM 9.5″

from

$188.99

Bearing race driver. No return.

Product Features:

Bearing race driver
Fits 382A race
All steel construction

from

$8.79

Value-priced bearing meets all cataloged application requirements.

Product Features:

Brand may vary by location

from

$55.99

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

from

$39.99

Pinion seal with triple-lip design for ’98 and newer GM 14T.Yukon Mighty seal.

Product Features:

Pinion seal
Fits 1998 and up GM 10.5″ 14 bolt truck

from

$6.99

Cross pin bolt for Chrysler 8.25″, 9.25″ rear, Ford 7.5″, 8.8″, GM 12 bolt car & truck, 7.2″ IFs, 7.5″, 7.6″, 8.0″, 8.25″ IFS & 8.5″.

Product Features:

Cross pin bolt for Chrysler 8.25″ and 9.25″ rear, Ford 7.5″ and 8.8″, GM 12 botl car and truck, 8.5″, 8.25″ IFS, 8.0″, 7.625″, 7.5″ and 7.2″ IFS

from

$218.99

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

from

$3.99

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

All products are designed to meet or exceed OE quality, form, fit and funtion.

from

$156.99

Dana 60 & Dana 70 Power Lok cross pin shaft (TWO needed).

Product Features:

Cross pin shaft
Fits Dana Spicer 60 and 70
Powr Lok positraction only

from

$9.99

Product Features:

Inner oil slinger for Dana Spicer 60

from

$606.99

Yukon positraction internals for 9.5″ GM with 33 spline axles. Yukon uses higher quality materials and better techniques than OEM to ensure a longer lasting spider gear set. This kit does not include clutches. All components come with a one year warranty against manufacturing defects. These internals are for Eaton positractions only. They will not fit factory positractions.

Product Features:

Spider gear kit
Fits GM 9.5″ with Eaton positraction
Includes two side gears, four pinion gears, cross pin shaft, roll pin and spider gear thrust washers.

from

$11.44

Differential Drain P

from

$259.99

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

from

$17.99

Product Features:

NUT PINION – 14 BOLT

from

$53.99

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

Premium bearing design matches OEM specifications
Precision manufactured using premium-grade steel for outstanding durability and performance
Crowned raceways and rollers to ensure even load distribution for maximum life
Industry leading coverage
Professional technicians know they can depend on National