Chevrolet Commercial Chassis Performance and Racing Products
Top Chevrolet Commercial Chassis Performance and Racing Products Categories
We carry over 23 Performance and Racing Products in inventory for the Chevrolet Commercial Chassis. If you’re looking for aftermarket Performance and Racing Products for your Chevrolet Commercial Chassis, check out all these categories:
Essential Chevrolet Commercial Chassis Performance and Racing Products
Energy Suspension – Motor Mount (Part No.3.1141R)
from
$63.99
A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.
Product Features:
See More
Product Features:
- Gains Both Performance and Longevity
- Will Handle Any and All Torque
- Out Lasts Rubber
Energy Suspension – Motor Mount (Part No.3.1141G)
from
$64.99
A true performance application component for cars, trucks, hot rods and racing/competition vehicles – yet designed to be also used for street vehicles. Soft-running enough to absorb vibrations for street use yet rugged for racing use. When required- a torque resistant safety interlock design is used that is comparable in strength to those too hard-running metal mounts. Replaces the original, short lived and typically too-soft rubber mounts and outdates those hard-running metal motor mounts. The popular early style mounts for General Motors vehicles are available in either zinc or chrome metal finishes. Made of Hyper-Flex performance polyurethane. Resistant to under vehicle fluids such as: oils, coolants, road contaminants, etc.
Product Features:
See More
Product Features:
- Gains Both Performance and Longevity
- Will Handle Any and All Torque
- Out Lasts Rubber
MSD Ignition – Distributor; Billet; Chevy V6 Even-Fire (Part No.8597)
from
$545.99
Starting on the inside, a 0.500 In. oversized steel shaft spins in a sealed ball bearing and sintered bushing for long endurance and accurate spark delivery throughout the entire RPM range. Mounted on top of the shaft is an easy-to-adjust chromoly mechanical advance assembly. Different advance springs and stop bushings are supplied so you can choose from 24 curves. A maintenance-free magnetic pick-up provides accurate trigger signals to your MSD Ignition control. A precision-manufactured reluctor that is connected to the shaft is responsible for triggering the pick-up. The distributor is topped off with a high quality black cap and race rotor.
Product Features:
See More
Product Features:
- CNC machined billet aluminum housing and billet aluminum base
- Will not accept a vacuum advance canister
- Must Be Used w/An MSD Ignition Control
- O-ring seals can be installed for oil press. control (Mods only)
- Supplied w/Socket Style Distributor Cap And Rotor
- Special oil tract improves lubrication to the dist./cam gear
- Nylon pads ensure smooth operation of the advance weights
- Advance weight pins are staked and tig welded to the plate
Competition Cams – Xtreme Energy 250/256 Hydraulic Flat Cam and Lifter Kit Chevrolet Small Block (Part No.CL12-254-3)
from
$321.99
SMALL BLOCK CHEVY HYDRAULIC CAM AND LIFTER KIT – Xtreme Energy: Pro Street/bracket, needs good intake, headers, gear and 3300+ stall.
Product Features:
See More
Product Features:
- Cam and lifter kit for Small Block Chevy engines
- CL-Kit includes cam, lifters, assembly lube, instructions and decals
- HYDRAULIC – Xtreme Energy: Pro Street/bracket, needs good intake, headers, gear and 3300+ stall.
- 294/306 Advertised Duration, 250/256 Duration @ .050″, .519″/.523″ Lift, 110 Lobe Separation
- Valve spring upgrade required
Competition Cams – CAM & LIFTER KIT, SBC 260H HIGH ENERGY HYD 1 KT (Part No.CL12-206-2)
from
$323.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Mr. Gasket – Thermocap Radiator Cap (Part No.2470R)
from
$48.09
The fastest, easiest way to know exactly when it’s safe to open your radiator cap. ThermoCap, with its built-in calibrated thermometer, indicates the coolant temperature.
Product Features:
See More
Product Features:
- Indicates coolant temperature
- Helps prevent coolant injuries
- Fahrenheit and centigrade readings
- Color-coded temperature ranges
- Integrated coolant reclamation valve
- Improves under-hood appearance
- Chromed crown with a colored trim ring
K&N – Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine (Part No.HP-2001)
from
$17.99
K&N premium oil filters are meticulously engineered to offer outstanding filtration and engine protection. Designed to operate with all synthetic, conventional, and blended motor oils, K&N’s pleated synthetic-blend filtration media helps to shield your engine from contaminants and ensure a consistent flow of oil. The heavy-duty canister is engineered to be exceptionally durable, and a one-inch welded hex nut can be used for quick and easy filter removal. Each filter is specifically designed to withstand the service intervals recommended by vehicle manufacturers.
Product Features:
See More
Product Features:
- HIGH FLOW RATES: Designed to provide exceptional flow rates and a consistent flow of oil to your engine
- VERSATILE COMPATIBILITY: Designed to operate with all synthetic, conventional, and blended motor oils
- PROTECT YOUR ENGINE: Pleated synthetic-blend filtration media removes most harmful contaminants
- EXTENSIVELY TESTED: Laboratory tested to ensure excellent capacity and burst strength
- EASY TO REMOVE: Fast and easy Wrench-Off removal
- HEAVY-DUTY CONSTRUCTION: Heavy-duty canister for outstanding durability
- HIGH CAPACITY: Withstand the longer service intervals now recommended by some vehicle manufacturers
Edelbrock – Intake Manifold Gasket for 1985-1995, Chevy V6 200-229-262 (Part No.7209)
from
$27.99
Edelbrock part #7209 Intake Gaskets for 1985-1995, Chevy V6 200-229-262 (3.8 and 4.3L) allow for optimum flow and performance. Any gasket can create a seal, but a good gasket can do it with less clamping force, and for a longer period of time. The new MP-
Product Features:
See More
Product Features:
- 1.28″x2.10″
- Stock Port Style
- .060″ Thick
- Multi Piece Configuration
- Composite Material
B & M – Automatic Shifter, Unimatic Shifter (Part No.80775)
from
$269.99
The B&M Unimatic is an ideal replacement for column shift vehicles, includes neutral safety switch, 5 foot cable and a boot and plate.
Product Features:
See More
Product Features:
- Ideal As Column Shift Replacement
- Includes Neutral Safety Switch
- Includes Black T-Handle
- Backup Light Not Available
- Includes 5 ft. Cable and Hardware
- Includes Boot and Plate
Hays – Power Train (Part No.10-025)
from
$148.99
Constructed of thicker than stock steel plate to withstand the stress of high stall speed converters and high RPM engine. Zinc dichromate plated to resist rust and corrosion. Meets SFI specification 29.1 for racing.
Product Features:
See More
Product Features:
- Thicker Than Stock Steel Plate
- Ring Gear Securely Welded
- Dual Bolt Patterns
- Zinc-Dichromate Plated To Resist Corrosion
- Withstands High Torque and RPM
Hays – Power Train (Part No.10-530)
from
$499.99
Hays aluminum flywheels are manufactured from certified billet material that will not break up under the stress of high RPM and severe punishment of racing. Features replaceable steel surface insert. Precision balanced to either neutral (internal) or Detroit (external) specifications. Meets SFI specification 1.1 for racing.
Product Features:
See More
Product Features:
- Certified Billet Material
- Borg and Beck Clutch Pattern
- Long-Style Clutch Pattern
- Ring Gear Securely Mounted To Prevent Spinning
Accel – GM 1984-95 Remote Supercoil (Part No.140011)
from
$79.99
Engineered with optimized low resistance, high turns ratio windings around an M36 high silicone magnetic steel E-core for higher energy and voltage outputs. Compatible with late model GM computer controlled remote mount HEI systems. Direct bolt-in, plug-in replacement. Brass coil wire contact increases energy transfer and resists corrosion better than aluminum. Complete with new mounting hardware.
Product Features:
See More
Product Features:
- 10-15% More Energy
- Direct Plug In Replacement Direct OE Fit
- Advanced Bobbin Technology
- Highly Specialized Silicone Magnetic Steel Cores
- Standard Motor Products SMP DR-37
- MSD 8226
- Resist Corrosion
- W/New Mounting Hardware
MSD Ignition – Coil; GM External HEI Coil; High Performance (Part No.8226)
from
$71.99
Top off your GM ignition system with these great new replacement coils. The GM coils have MSD performance in factory style housings. MSD designed these coils by combining our blaster coil experience with e-core coil efficiency. Each coil has a unique turns ratio plus there is lower primary resistance than the stock coil. This all amounts to a bolt-in replacement coil that produces more output voltage. The coils will work with stock ignition systems as well as MSD equipped cars and trucks. Installation tip: If you plan to install an MSD ignition with your GM dual connector coil, use PN 8876 harness for a direct plug-in installation.
Product Features:
See More
Product Features:
- Direct performance replacement for GM dual connector coil
- 100:1 Turns Ratio
- Lower Primary Resistance Produces High Voltage Output
- Works w/Stock Ignition As Well As MSD Ignitions
Edelbrock – Sure Seat Valve Springs for S/B Chevy O.E Cast iron Cylinder Heads (Part No.5703)
from
$65.99
Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.
Product Features:
See More
Product Features:
- For Use With Cast Iron Heads
- Springs Made of Highest Quality Spring Wire
- Springs Precision Wound To Close Tolerances
- Use with Original Equipment Heads Only
Edelbrock – Sure Seat Valve Springs for Chevy 4.3L 90 Deg V6 1987-95 (Part No.5814)
from
$53.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks black oxide coated. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.
Product Features:
See More
Product Features:
- For Use With Cast Iron Heads
- Springs Made of Highest Quality Spring Wire
- Springs Precision Wound To Close Tolerances
- Use with Original Equipment Heads Only
Edelbrock – Complete Sure Seat Valve Spring Kit for Chevy 262-400 V8 1957-95 (Part No.5894)
from
$147.99
Complete kit includes retainers and locks. Springs made of highest quality spring wire. Springs precision wound to close tolerances. Includes superior quality steel retainers. Includes 7 degree heat-treated valve stem locks. Retainers and locks are black oxide coated. Non-rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.
Product Features:
See More
Product Features:
- Complete Kit: Includes Retainers And Locks
- Springs Made of Highest Quality Spring Wire
- Springs Precision Wound To Close Tolerances
- Includes Superior Quality Steel Retainers
- Includes 7 deg. Heat-Treated Valve Stem Locks
- Retainers and Locks Black Oxide Coated
- Dyno Tested And Street Proven
- Great Match to Edelbrock Camshaft Kit
Competition Cams – CAMSHAFT, SBC 252 HIGH ENERGY HYDRAULIC 1 EA (Part No.12-205-2)
from
$518.99
Ideal for use with mainly stock components like rocker arms, intake manifolds, cylinder heads, compression ratio, torque converters and rear gear ratios, the High Energy camshaft grind family is a great choice for street performance applications. Offering
Product Features:
See More
Product Features:
- Good blend of efficiency and performance.
- Perfect choice for performance street rebuilds.
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
Competition Cams – CAMSHAFT, SBC 249 XTREME ENERGY COMPUTER CONTROLLED HYDRAULIC 1 EA (Part No.12-249-4)
from
$276.99
Featuring a quicker valve opening, the Xtreme Energy camshaft profile provides increased responsiveness and more area under the lift curve than older, slower grinds. Designed to increase performance without sacrificing driveability and creature comforts, the Xtreme Energy grind family offers gains in torque and horsepower while still delivering adequate vacuum for power brakes and other vacuum dependent accessories. Xtreme Energy camshafts work great in carbureted applications, but offer the best performance with aftermarket intake manifolds, lower gear ratios, headers and free flowing exhaust.
Product Features:
See More
Product Features:
- HYDRAULIC – Xtreme Energy Computer Controlled: Great in throttle body, crossfire or carbureted engine and 305 TPI.
- 249/260 Advertised Duration, 206/212 Duration @ .050″, .434″/.444″ Lift, 112 Lobe Separation
- Quicker opening lobe profiles deliver increased responsiveness and more area under the lift curve.
- Best performance with aftermarket intake manifolds, headers, lower gear ratios etc.
Competition Cams – THUMPR CAMSHAFT, SBC 1 EA (Part No.12-600-4)
from
$587.99
Designed to deliver an aggressive, hard-hitting exhaust note at idle, the Thumpr camshaft series from COMP Cams also delivers excellent horsepower gains and a broad torque curve. A perfect choice for muscle cars and street rods, the Thumpr series’ early i
Product Features:
See More
Product Features:
- Early intake valve opening and long exhaust duration create optimum overlap for powerful, hard-hitting exhaust note.
- Best with aftermarket converters and more rear gear.
- Three unique cam designs for each application that deliver excellent horsepower gains and broad torque curve; perfect choice for muscle cars and street rods.
Competition Cams – High Energy/Marine 212/212 Hydraulic Flat Cam for Chevrolet Small Block (Part No.12-206-2)
from
$284.99
HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
Product Features:
See More
Product Features:
- HYDRAULIC – High Energy: Vans, pickups, 4WD and towing, in 350c.i., good idle, strong mid-range torque. OR High Energy Marine: Single or dual engine with inboard/outboard drive for ski and economy.
- 260/260 Advertised Duration, 212/212 Duration @ .050″, .440″/.440″ Lift, 110 Lobe Separation
- Work well with mainly stock components such as rockers, manifolds, heads, compression, torque converters and gears.
MSD Ignition – Distributor Cap and Rotor; GM 4.3L; External Coil (Part No.8430)
from
$48.49
The cap and rotor of any ignition system must be considered maintenance items. Just as you change the oil and filter of your car, you should always replace the cap and rotor as a set. To make things easy, we now offer these cap and rotor replacement kits.
Product Features:
See More
Product Features:
- Designed w/performance in mind
- High quality; voltage insulating material
- Stainless Terminals
- High dielectric properties
Chevrolet Commercial Chassis Performance and Racing Products Categories
Helping You Find the Right Performance and Racing Products for Your Chevrolet Commercial Chassis
You love your Commercial Chassis. So we’ve made it easier than ever to help you find Chevrolet Commercial Chassis Performance and Racing Products in our online catalog. Our inventory holds 23 aftermarket and OEM Performance and Racing Products for your Chevrolet Commercial Chassis, ranging from $17.99 to $587.99.
We offer parts from 9 brands trusted to make quality Performance and Racing Products for your Chevrolet Commercial Chassis. Before you buy, take some time to read through customer reviews. We currently have 200 reviews of Chevrolet Commercial Chassis Performance and Racing Products from previous customers. Some of the top rated parts include Distributor; Billet; Chevy V6 Even-Fire with 5.0 stars and Automatic Shifter, Unimatic Shifter with 4.3 stars.
Find your Commercial Chassis Performance and Racing Products here, order online, and have your order shipped directly to your home. Prefer to have an in-person look at your Chevrolet Commercial Chassis part to confirm it’s just right? You can find your nearest Advance Auto Parts store and confirm they have the part in stock before heading over.
Top Performance and Racing Products Brands for Your Chevrolet Commercial Chassis
Our inventory holds Performance and Racing Products for your Chevrolet Commercial Chassis from 9 trusted brands. You’ll find OEM and aftermarket parts from brands like K&N, MSD Ignition, and Accel, all of which can keep that Chevrolet happy.
We have K&N parts available for your Chevrolet Commercial Chassis in categories like Performance Oil Filters. Some of the top-rated K&N parts in these categories are:
from
$17.99
(29)
Premium Oil Filter: Ideal for Synthetic & Conventional Oil, Protects Your Engine
Performance Oil Filters
FAQs for Chevrolet Commercial Chassis Performance and Racing Products
What are the most purchased Performance and Racing Products for the Chevrolet Commercial Chassis?
Out of 23 Performance and Racing Products for the Chevrolet Commercial Chassis, the most popular in our inventory are:
from
$48.49
This product is not rated
Distributor Cap and Rotor; GM 4.3L; External Coil
Performance Distributor Cap and Rotor Kits
What are the top-rated Chevrolet Commercial Chassis Performance and Racing Products?
Top-rated Performance and Racing Products for your Chevrolet Commercial Chassis based on customer reviews/ratings are:
from
$64.99
(2)
Motor Mount
“Bought these for my dad’s 1992 S-10 with 4.3L Z-vin engine because the driver’s side motor mount had broke twice within just a few years. All holes a”
