from

$31.99

COMP Cams offers a complete line of valve stem seals, from the umbrella seals to the positive-stop Teflon seal. These seals are a must to keep unwanted oil from entering the combustion chamber through the clearance in the valve guides. The umbrella seal is normally used when a larger-than-stock diameter spring is used, in the case of a double spring, the positive-stop Teflon seal is used. The umbrella seals require no machining, but with the Teflon seal it is necessary to disassemble the heads and machine the top of the guide with a special .530 diameter cutter. Whenever you are planning an engine overhaul or a cam change, don’t forget the valve seals.

Product Features:

Work with .530″ guides and 3/8″ valve stem diameter
Valve stem oil seals keep unwanted oil from entering the combustion chamber
Several different types of valve seals are offered

from

$112.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$65.99

Springs made of highest quality spring wire. Springs precision wound to close tolerances. Non-Rotator style: Dyno tested and street proven. Great match to Edelbrock camshaft kit.

Product Features:

For Use With Cast Iron Heads
Springs Made of Highest Quality Spring Wire
Springs Precision Wound To Close Tolerances
Use with Original Equipment Heads Only

from

$151.99

MiniSpool

from

$9.99

Add sparkle to your engine with this chromed hold-down clamp. With bolt and gasket. Serrations on the bottom prevent distributor and magneto rotation for accurate timing.

Product Features:

Rolled Edges For Strength
Ideal For Magnetos
Ideal For Ignition Distributor

from

$45.99

Manufactured from high-temperature steel core/graphite faced exhaust material. Expanded steel core provides stability and maximum torque retention to eliminate gasket failure. Graphite facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head. Conforms to and seals minor surface irregularities. High recovery material allows header or manifold flange to stay sealed if flange loses clamp-load. Can be trimmed if necessary for modified port applications. For original equipment replacement, high performance street, drag race and oval track use.

Product Features:

Manufactured from high-temperature steel core/graphite faced exhaust material.
Expanded steel core provides stability and maximum torque retention to eliminate gasket failure
Graphite impregnated facing provides excellent heat resistance and thermal conductivity to transfer heat away from the cylinder head
Conforms to and seals minor surface irregularities
Can be trimmed if necessary for modified port applications
For OE replacement, high performance street, drag race and oval track use
Anti-Stick Properties
Easy Removal For Disassembly

from

$222.99

Product Features:

GM 10BL 8.5 R/P 4.10 FRT/REAR MGP

from

$702.99

The Buick Nailhead is one of the most sought after nostalgic engines for rods and is still providing the smooth power to plenty of Buick’s. Nailhead fans can finally get a state-of-the-art distributor to provide the fire! MSD’s Nailhead distributor is a ready to run unit which incorporates a magnetic pickup that never wears out. Plus, the distributor has a built in ignition module so there is no need to mount an external MSD Ignition control. The module delivers up to 7.5 A to the coil creating a stout inductive spark. Not only do you get the benefits of electronic triggering, but your engine will awaken with powerful sparks from the ignition module. This improves combustion of the fuel mixture resulting in quick starts, a smooth idle and great performance.

Product Features:

Simple and clean three wire installation
Includes built-in Rev Limiter
Does not require an MSD Ignition Control
Supplied w/HEI style distributor cap/rotor (accepts Cap-A-Dapts)
Mech. advance assem. can be locked out for crank trigger systems
Advance plate and weights are fine blanked from chrome moly steel
QPQ coated for friction reduction
QPQ coated polished steel shaft; guided by sealed ball bearings
Maintenance-free magnetic pickup and precision reluctor
Creates stable trigger signals throughout the rpm range
CNC machined billet aluminum housing and billet aluminum base
Vacuum advance canister for improved economy (can be locked out)

from

$10.99

Repair torn and worn-out boots of suspension tie rod ends – without having to buy the entire and expensive tie rod. Adds durability surpassing most OEM rubber boots. Exclusive 5 point sealing action. Choose from four sizes and round or octagon styles. Made of Energy’s Hyper-Flex performance polyurethane for added performance and durability.

Product Features:

Easy to Install
Superior Material
Lasts Longer
Looks Great

from

$17.99

Product Features:

For Small-Block Chevy
One Piece Configuration
Includes Front Cover Gasket & Front Seal
Includes Necessary Gaskets & Crankshaft Oil Seal
For Replacement Or Installation

from

$108.99

What better way to check you oil level by using one of B&M’s transmission fluid dipsticks? The cap screws into the tube and is O-ring sealed, while the base of the tube has a sealing grommet where it goes into the transmission.

Product Features:

Automatic Transmission Dip Stick
Mounts to bellhousing
Sold as a kit
Natural finish
Fits TH350 & TH350C

from

$105.99

Put an end to high maintenance points ignition systems by installing an ACCEL points eliminator ignition conversion kit. By utilizing specialized electronic circuitry and an infrared signal, ignition timing is stable from 1 to 10,000 RPM. More accurate ignition timing than any other type of system. Improves performance and fuel efficiency. Easy to install with simple hand tools. Reduced maintenance-eliminates changing points forever. Latest thermal clad based surface mount construction for maximum dependability and long life. Available for all popular 12-volt negative ground domestic cars and trucks.

Product Features:

More Accurate Ignition Timing
Improves Performance And Fuel Economy
Provides More Accurate Ignition Timing
Easy To Install w/Hand Tools
Reduced Maintenance
Thermal Clad Based Surface Mount Construction
Utilizes Specialized Electronic Circuitry
Ignition Timing Is Stable From 1 To 10000rpm

from

$158.89

Hypertech Power Chips are engineered for stock 1981-1995 GM vehicles. The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. Street Runner Power Chips are designed for daily street driving or competition in unmodified vehicles using a stock thermostat.

Product Features:

Designed For Daily Street Driving
For Unmodified Vehicles w/Stock Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$17.49

The special self locking oil pan bolts, use a smaller-than-standard hex head is ideal for tight spaces. Because of the hex flange head design, it will not fall back into the socket wrench, allowing for easier installation. Special under head serrations prevent loosening and the wide flange head distributes uniform clamping pressure for an ultra gasket seal. Bolts are zinc plated, grade 5.

Product Features:

Ideal For Tight Spaces
Serrations Prevent Loosening
Flange Distributes Pressure
Zinc Plated Bolts
Grade 5 Material
Easy Installation

from

$154.99

For both front and rear of suspensions on cars, trucks and SUVs. Maintains proper alignment under extreme conditions on and off-road and during competition. Improves vehicle handling, cornering and overall control. Full floating for smoother operation. Made of Energy’s Hyper-Flex performance polyurethane to add performance and durability.

Product Features:

Maintains Better Alignment While Driving
Full Floating and Non Binding
Fits Into the Remaining Stock Control Arms

from

$168.89

Hypertech ThermoMaster Power Chips are engineered for stock 1995-1981 GM vehicles (premium octane fuel required). The Power Chip contains the Hypertech Power Tuning data that controls the engine’s air/fuel ratio and spark advance for maximum power and performance, plus potential gas mileage improvements. Power Chips can be easily installed, using only hand tools. ThermoMaster Power Chips are designed for daily street driving or competition in unmodified vehicles using a 160 Deg. or 180 Deg. thermostat. Hypertech Power Chips(TM) are emissions certified 50-state legal (application specific).

Product Features:

Use w/Low-Temp 160-180 Deg. PowerStat Thermostat
Controls Engines Air/Fuel Ratio
Controls Spark Advance For Max Power
Potential Gas Mileage Improvements
No Wiring Or Soldering Required
Installs In Less Than 30 Minutes
Product might not be available in all states due to local laws.

from

$62.99

Product Features:

Solid Bushing Chain Resists Stretching
For Use with Stock or Edelbrock Camshafts
Stressproof Steel Crank Gears
3 Keyway Setting Points To Ensure Accurate Timing
True Bearing Surface Rolls with the Sprockets
Not for OEM Hydraulic Roller-Lifter Camshaft Eng.

from

$73.99

The B&M Shift Improver Kit the easiest way to get the performance you’ve always wanted out of your automatic transmission, two modes to select from: Heavy Duty, or Street/Strip. It’s our least expensive and simplest to install kit.

Product Features:

Provides Crisp Shifts
On Any Stock Automatic Transmission
Eliminates Soft/Sluggish Shift
Eliminates Shift Overlap
Eliminate Clutch and Band Wear
Improves Transmission Life
Transmission Removal Not Required

from

$89.99

K&N washable, reusable High-Flow Air Filters feature a state-of-the-art design of layered, oiled cotton media engineered to improve airflow and capture contaminants, and are designed to provide an increase in horsepower. Each performance air filter is reusable and engineered to last for the entire lifespan of your vehicle. K&N drop-in replacement filters are designed to install easily into your factory air box. Upgrade today and start enjoying superior airflow and superior performance from K&N’s most popular product!

Product Features:

REUSABLE K&N FILTER SAVES YOU MONEY: A K&N washable, reusable air filter will save you up to $125 vs. purchasing multiple disposable filters (compared to MSRP in USD of corresponding OE filters for 200,000 miles of highway driving)
CLEAN ONCE EVERY 5 YEARS: Engine air filter only needs cleaning every 75,000 miles under normal highway driving conditions (5 years based on the average miles driven per year of 15,000 miles)
RUGGED CONSTRUCTION: K&N Air Filters are manufactured with durable, premium materials and state-of-the-art construction methods to last a lifetime
REDUCES WASTE: Over 200 million disposable air filters and their packaging waste wind up in landfills each year- reusable filters help reduce waste in our landfills
ENGINEERED POWER: State-of-the-art air filter media is designed to increase horsepower and acceleration as well as improve overall engine performance
EASY INSTALLATION: K&N Air Filters are pre-oiled and ready to drop into your factory air box- they are one of the easiest and most cost-effective vehicle upgrades for quick performance gains
4 LAYERS OF PROTECTION: Multiple layers of premium cotton gauze treated with a specially-designed tacking agent work together to create an intricate mesh of engine filter media that is designed to block and trap harmful contaminants

from

$53.99

When a high pressure fuel pump is run with a steel roller cam core, the stock fuel pump pushrod is not compatible with the steel core. You can damage an expensive roller cam as a result of wear at the fuel pump lobe. COMP Cams offers several fuel pump pushrods for various applications.

Product Features:

Lightweight tubing with bronze tip for steel cams
5.75″ Length
Eliminates wear at the fuel pump lobe often caused by a stock fuel pump pushrod

from

$23.79

Spectre’s Chevrolet late model water neck offers the normal angled water neck and a 1/2 inch NPT threaded hole for a by-pass hose. This water neck has a chrome plated finish for a lasting look great and includes the bolts.

Product Features:

Fits Chevy engines
Includes a 1/2 inch NPT threaded hole for by-pass hose
Includes bolts
Chrome plated
Easy to install
O-ring/gasket not included

from

$168.99

Product Features:

Unique Valve Design
Improves Flow Quantity/Quality
Supports Engines Up To 550 HP
Hi-Vol 0.375 in. NPT Inlet/Outlet
Produces 6 psi
Gasoline Or Mixed Fuels Only

from

$15.99

Bolts on with existing timing cover bolts. It is chrome plated steel, which makes is a better compliment to a chrome timing cover. It also has an adjustable red timing pointer. This allows for better visibility and helps you set your timing more easily. Just loosen the screw, set the pointer to the desired initial timing level, and screw it back down. Then you’ll be able to more clearly see if your timing is where you want it when checking your timing.

Product Features:

Bolts on using existing timing cover bolts
Chrome finish compliments chrome timing covers
Red adjustable pointer makes it easier to check timing

from

$439.99

The B&M Quicksilver features a ratcheting action for positive shifts, Chrome Knob, neutral safety switch, NHRA/IHRA approved Reverse Lockout. Fits Most 3 and 4 speeds.

Product Features: