2022 Audi A5 Quattro Engine Cooling Parts

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Engineered for the sealing repair environment
• Validated for fit, form and function
• Unsurpassed quality you can trust

Rein Automotive OE quality coolant pipes fit European vehicles the way the original manufacturer intended. Designed to be a direct replacements for the OE coolant, Rein coolant pipes are identical to the OEM.

Product Features:

• Designed as direct-fit replacements to ensure trouble-free proper installation.
• Made to strict engineering quality standards.
• Part is produced using only the highest quality materials.
• Resistant to heat, salt, road debris, oil and other contaminants.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

• OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
• FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
• THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

• Designed to OE standards for ease of installation
• In manufacturing, we custom form the wax pellets for different temperature range specifications. All units are calibrated & tested to confirm switch actuation at their specified temperature
• The switch is designed using a formed bimetallic contact arm. The bimetal contact movement is achieved using the different expansion rates of two metals fused together. This is a creep action device, provides precise performance
• In production, all thermal switches are factory-calibrated to make electrical contact at the specified lower-temperature set point
• Robust design and high grade materials meet the stringent demands of today’s service professional

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Water Temp. Sensor

This new pump is 100% tested to ensure the highest quality. Each unit is built to meet or exceed all OE specifications and is validated for fit, form, and function. Application specific design to ensure a perfect fit and correct operation for unsurpassed quality.

Product Features:

• All components necessary for installation are supplied with pump
• Plastic housing
• Follow all enclosed instructions to maximize pump life and validate warranty
• Specialized for vehicles using supplemented cooling for the engine or components

Carquest Premium auxiliary water pumps are 100% new, high-quality parts that meet or exceed original equipment (O.E.) specifications. All components, including the housing, impeller, controller, gaskets, and seals are designed for long-lasting service life. These electric water pumps are supplied with the gaskets or seals necessary for installation. Our Carquest Premium auxiliary water pumps undergo stringent testing to ensure superior performance that we stand behind with an industry-leading warranty.

Product Features:

• Built to meet or exceed OE fit, form and function
• All components necessary for installation are supplied with pump
• 100% tested for reliable performance
• Follow all enclosed instructions to maximize pump life and validate warranty

The product selection from Pierburg Pump Technology covers the complete range of applications for electric water circulation and coolant pumps in the automotive industry. Pierburg has extensive experience in the area of electric water pumps, especially with regard to EC engine technology and hydraulics. The canned motor concept was selected to meet the high requirements for operational reliability and service life. This special motor design has an additional tube placed in the space between the stator and the rotor, which keeps the stator statically sealed with respect to the medium pumped by the running rotor. Since this drive system requires no dynamic sealing elements which are subject to wear (rotating mechanical seals), the water circulation and coolant pumps are especially reliable and free of wear problems. Moreover, the EC motor used in the pumps requires no brushes. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

• OE Quality, reliability and service life
• Reduction in noise
• Leak-proof sealing of the drive
• Fuel savings and reduced emissions
• Cooling even without operation of the engine
• Water circulation pump can deliver as much as 800 liters per hour
• Coolant pump can deliver more than 9,000 liters per hour

The product selection from Pierburg Pump Technology covers the complete range of applications for electric water circulation and coolant pumps in the automotive industry. Pierburg has extensive experience in the area of electric water pumps, especially with regard to EC engine technology and hydraulics. The canned motor concept was selected to meet the high requirements for operational reliability and service life. This special motor design has an additional tube placed in the space between the stator and the rotor, which keeps the stator statically sealed with respect to the medium pumped by the running rotor. Since this drive system requires no dynamic sealing elements which are subject to wear (rotating mechanical seals), the water circulation and coolant pumps are especially reliable and free of wear problems. Moreover, the EC motor used in the pumps requires no brushes. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

• OE Quality, reliability and service life
• Reduction in noise
• Leak-proof sealing of the drive
• Fuel savings and reduced emissions
• Cooling even without operation of the engine
• Water circulation pump can deliver as much as 800 liters per hour
• Coolant pump can deliver more than 9,000 liters per hour

This new pump is 100% tested to ensure the highest quality. Each unit is built to meet or exceed all OE specifications and is validated for fit, form, and function. Application specific design to ensure a perfect fit and correct operation for unsurpassed quality.

Product Features:

• Electric water pump
• Specialized for vehicles using supplemented cooling for the engine or components
• Plastic housing
• All components necessary for installation are supplied with pump
• Follow all enclosed instructions to maximize pump life and validate warranty

Auxiliary Water Pump

Heater Pipe O-Ring

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

Water Temperature Sensor O-Ring

Water Pipe O-Ring

With Victor Reinz gaskets, you can be sure you are getting sealing solutions that deliver OE quality gasket technology and engineering. That is because Victor Reinz is an original equipment supplier and the trusted choice of manufacturers the world over, offering broad coverage for foreign and domestic cars and trucks. In Victor Reinz gasket sets, you get the right combination of components needed for fast, long-lasting repairs.

Product Features:

• Choosing Victor Reinz assures getting OE quality parts in gaskets sets that have the coverage, contents, packaging and electronic cataloging to best meet the needs of the aftermarket.

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

• Thermal tested under real-life temperature simulations
• High tensile strength aluminum for maximum crimp strength
• Plastic tanks are engineered with integrated ribbing for added strength to withstand cracks, bowing and distortion during thermal cycles
• Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles
• Oil cooler designs meet or exceed OE standards, keeping the vehicle’s engine and transmission performing at optimal conditions
• OEM grade, premium fittings for transmission or engine oil coolers (where applicable)

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

• Thermal tested under real-life temperature simulations
• High tensile strength aluminum for maximum crimp strength
• Plastic tanks are engineered with integrated ribbing for added strength to withstand cracks, bowing and distortion during thermal cycles
• Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles
• Oil cooler designs meet or exceed OE standards, keeping the vehicle’s engine and transmission performing at optimal conditions
• OEM grade, premium fittings for transmission or engine oil coolers (where applicable)

Carquest Premium radiators are designed and engineered for maximum performance, using the highest-grade materials to ensure all radiators meet or exceed original equipment (O.E.) fit, form and function. Carquest Premium radiators are built by manufacturers that meet IATF 16949 certified framework, an internationally recognized proof of quality in the automotive industry. Most modern vehicles use radiators with plastic tanks and our parts are engineered with integrated ribbing to prevent damage during thermal cycling. Carquest Premium radiators are also 100% tested to ensure a durable, leak-free cooling system repair.

Product Features:

• Thermal tested under real-life temperature simulations
• High tensile strength aluminum for maximum crimp strength
• Plastic tanks are engineered with integrated ribbing for added strength to withstand cracks, bowing and distortion during thermal cycles
• Thermal expansion slots extend core life and reduce failure rates by allowing improved core expansion and contraction during systematic heat cycles
• Oil cooler designs meet or exceed OE standards, keeping the vehicle’s engine and transmission performing at optimal conditions
• OEM grade, premium fittings for transmission or engine oil coolers (where applicable)

Plastic Tank / Aluminum Core Radiator The Nissens Radiator flat tube and double folded fin design offers a significantly better cooling capacity and provides a stronger exterior resisting impacts from stones. This advanced design helps to prevent damage which would negatively affect the cooling capacity and engine performance.

Product Features:

• OE-Equivalent.
• Direct fit for easy installation.
• OE Style mounting brackets and hose connections.
• Integrated transmission oil cooler when applicable.
• Compact and lightweight.

Aluminum Core Radiator The Behr replacement radiator guarantees the same quality fit and performance as the OE radiator it replaces. The Behr radiator core is manufactured using high quality anti corrosive aluminum and fiber glass-reinforced polyamide coolant tanks that are highly resistant to cracking and deformation.

Product Features:

• OE-Equivalent
• Direct fit for easy installation.
• High quality corrosion resistant materials.
• OE Style mounting brackets and hose connections.
• Mechanically bonded aluminum core.
• Integrated transmission oil cooler when applicable.

Plastic Tank / Aluminum Core Radiator The Nissens Radiator flat tube and double folded fin design offers a significantly better cooling capacity and provides a stronger exterior resisting impacts from stones. This advanced design helps to prevent damage which would negatively affect the cooling capacity and engine performance.

Product Features:

• OE-Equivalent.
• Direct fit for easy installation.
• OE Style mounting brackets and hose connections.
• Integrated transmission oil cooler when applicable.
• Compact and lightweight.

New Platinum Pro Radiator, 2.0 Liter Engine With Built-In Transmission Oil Cooler

Product Features:

• 2.0 Liter Engine With Built-In Transmission Oil Cooler, Made Of Plastic and Aluminum
• Meets All Federal Motor Safety Standards
• No Drilling Needed For Installation
• No Modifications Needed For Installation
• Direct Fit Replacement For Your Vehicle
• Same Form Fit And Function As OE
• Check Out The Large Selection Of Parts Available For Your Vehicle