2021 Porsche Cayenne Cooling and Climate Controls

Water Pipe Gasket

The product selection from Pierburg Pump Technology covers the complete range of applications for electric water circulation and coolant pumps in the automotive industry. Pierburg has extensive experience in the area of electric water pumps, especially with regard to EC engine technology and hydraulics. The canned motor concept was selected to meet the high requirements for operational reliability and service life. This special motor design has an additional tube placed in the space between the stator and the rotor, which keeps the stator statically sealed with respect to the medium pumped by the running rotor. Since this drive system requires no dynamic sealing elements which are subject to wear (rotating mechanical seals), the water circulation and coolant pumps are especially reliable and free of wear problems. Moreover, the EC motor used in the pumps requires no brushes. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

• OE Quality, reliability and service life
• Reduction in noise
• Leak-proof sealing of the drive
• Fuel savings and reduced emissions
• Cooling even without operation of the engine
• Water circulation pump can deliver as much as 800 liters per hour
• Coolant pump can deliver more than 9,000 liters per hour

Auxiliary Water Pump

Restore your vehicle’s cooling system to proper working order, and minimize the risk of premature failure, by installing a Bosch Auxiliary Water Pump. Bosch Auxiliary Water Pumps are designed to operate in the highly-stressful environment of today’s cooling systems. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

• OE Quality, reliability and service life
• Leak-proof sealing of the drive
• Fuel savings and reduced emissions
• Cooling even without operation of the engine
• CO²-reduction by optimized efficiency, speed control and reduced weight
• Coverage of a wide hydraulic performance range
• Reduced noise level

The product selection from Pierburg Pump Technology covers the complete range of applications for electric water circulation and coolant pumps in the automotive industry. Pierburg has extensive experience in the area of electric water pumps, especially with regard to EC engine technology and hydraulics. The canned motor concept was selected to meet the high requirements for operational reliability and service life. This special motor design has an additional tube placed in the space between the stator and the rotor, which keeps the stator statically sealed with respect to the medium pumped by the running rotor. Since this drive system requires no dynamic sealing elements which are subject to wear (rotating mechanical seals), the water circulation and coolant pumps are especially reliable and free of wear problems. Moreover, the EC motor used in the pumps requires no brushes. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

• OE Quality, reliability and service life
• Reduction in noise
• Leak-proof sealing of the drive
• Fuel savings and reduced emissions
• Cooling even without operation of the engine
• Water circulation pump can deliver as much as 800 liters per hour
• Coolant pump can deliver more than 9,000 liters per hour

This engine auxiliary water pump is designed to match the fit and function of the original pump on specified applications, and is engineered for reliable performance and durability.

Product Features:

• Direct replacement – this engine auxiliary water pump is designed to match the fit and function of the original pump on specified applications
• Restores functionality – reliable replacement for an original pump that has failed to provide sufficient water flow
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

• Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
• Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
• All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
• All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging

The Premium CarQuest Vehicle Solutions line of vehicle electronics are designed for OE form, fit and function for both import and domestic vehicles. The A/C Pressure Sensor reports system pressures to the on-board computer, in turn allowing the computer to properly and efficiently control the compressor, fans and system levels. An improperly functioning A/C Pressure Sensor will provide erratic or inaccurate readings to on-board computers severely affecting system performance and function. Without reliable and accurate data from a properly functioning A/C Pressure Sensor, on-board computers are unable to protect the safety of critical components and the system as a whole which can lead to excessive wear and tear on critical components and costly system damage.

Product Features:

• Designed and manufactured with high quality materials, industry leading electronic components and strict quality controls. Engineered to exceed OE performance and to meet the uncompromising demands of service professionals.
• Direct fit replacement matches proper OE fit, form, and function and ensures trouble free installation of your A/C Pressure Sensor.
• All units are helium leak tested on fully automated mass spectrometer equipment before end-of-line testing.
• All units are tested using automated end-of-line testing equipment that pressurizes the A/C Pressure Sensor and checks full-spectrum functionality and electrical output to ensure each A/C Pressure Sensor meets manufacturing specifications before packaging

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

• OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
• FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
• THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

High-quality products that meet OE appearance and performance to provide professional technicians and DIYers with a cost-effective solution.

Product Features:

• Designed to OE standards for ease of installation
• In manufacturing, we custom form the wax pellets for different temperature range specifications. All units are calibrated & tested to confirm switch actuation at their specified temperature
• The switch is designed using a formed bimetallic contact arm. The bimetal contact movement is achieved using the different expansion rates of two metals fused together. This is a creep action device, provides precise performance
• In production, all thermal switches are factory-calibrated to make electrical contact at the specified lower-temperature set point
• Robust design and high grade materials meet the stringent demands of today’s service professional

Engine Coolant Temperature Sensor

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

CARQUEST premium engine management products provide the right products for a wide range of domestic and import applications. Delivering the highest performance and durability under demanding conditions.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Water Temp. Sensor

Approved materials for increased durability in even the most extreme temperatures. All MotoRad Coolant Temperature Sensors are designed to meet or exceed OEM specifications at our ISO TS16949 manufacturing facilities.

Product Features:

• 100% factory resistance calibrated to ensure precision tolerances, resulting in extremely accurate temperature for optimal performance
• Thread Sealant and/or O-ring pre-installed on applicable sensors to ensure leak free performance
• Brass sensor housing precision machined to meet or exceed OE thermal conductivity
• OE precision matched thermistor position for correct output parameters
• Extensive product testing includes salt spray, high/low temperature impact, thermal vibration, durability, static electricity, and micro tension, among other tests, to ensure all sensors meet or exceed OEM specifications.

Oil Drain Plug Gaske