2020 Toyota 4Runner Drivetrains

Essential Drivetrains for 2020 Toyota 4Runners

Valvoline – DEX/MERC Automatic Transmission Fluid, 1 Gallon (Part No.773636)

DEX/MERC Automatic Transmission Fluid, 1 Gallon

from

$35.99
Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:
  • Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
  • Enhanced anti-shudder protection for smooth shifting and maximum power transfer
  • Developed with anti-wear technology to help improve transmission durability
  • Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Yukon Gear – Pinion Install Kit For Toyota V6 Rear Differential (Part No.13092)

Pinion Install Kit For Toyota V6 Rear Differential

from

$299.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear. This kit fits applications with a 27 spline pinion.

Product Features:
  • Fits Toyota V6 rear
  • Included are pinion bearings and races, pinion seal, crush sleeve , complete pinion shim kit, and marking compound with brush.
See More

Beck/Arnley – Axle Seal (Part No.052-3644)

Axle Seal

from

$6.49
Beck/Arnley parts meet foreign nameplate OE specifications for form, fit and function. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.

Product Features:
  • Matches OE form, fit and function
  • High quality rubber designed to keep water and dirt out
  • Quality construction for durability
  • Designed for under vehicle environment
  • Application specific for this vehicle
See More

SKF – Wheel Bearing (Part No.K8000323893SKF)

Wheel Bearing

from

$105.89
SKF is a supplier of original equipment wheel bearings, hubs and seals to most of the world’s leading automakers. Engineered and manufactured to the highest quality standards, SKF wheel bearings greatly reduce friction and increase load-carrying capabilities. With an ability to boost reliability under heavy loads and misaligned conditions, SKF wheel bearings offer an ideal solution for many wheel end applications.

Product Features:
  • Precision bearing pre-load and correct application of advanced manufacturing techniques such as orbital rolling
  • 100% tested to the actual OE specifications per part number for fit, form and function
  • High quality steel and surface finishes
  • Proper implementation of heat treatment
See More

Yukon Gear – Spindle Nut Kit For Toyota Front (Part No.33513)

Spindle Nut Kit For Toyota Front

from

$24.99
Product Features:
  • Spindle nut kit for Toyota front
See More

NOK – Diff. Side Cover Sea (Part No.J7041160611NOK)

Diff. Side Cover Sea

from

$20.98
Diff. Side Cover Sea

Yukon Gear – Master Overhaul Kit For Toyota V6, ’03 & Up (Part No.14212)

Master Overhaul Kit For Toyota V6, '03 & Up

from

$491.99
Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), Thread locking compound, marking compound with brush, and gasket. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application. This kit fits applications with a 29 spline pinion.

Product Features:
  • Fits Toyota V6 rear
  • 29 spline only
  • Included are KOYO bearings and races along with high quality seals and small parts.
  • Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve , oil baffles and slingers , thread locker, marking compound with brush, and gasket.
See More

USA Standard Gear – Master Overhaul Kit for Toyota 7.5" IFS Differential, V6 (Part No.37111)

Master Overhaul Kit for Toyota 7.5" IFS Differential, V6

from

$363.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:
  • Fits reverse rotation Toyota 7.5″
  • Uses Koyo bearings and races
  • Included are carrier bearings and races, pinion bearings and races, pinion seal, axle seals, complete shim kit, ring gear bolts, pinion nut, crush sleeve, oil baffles and slingers, thread locker, marking compound with brush and silicone.
See More

Driveworks – Universal Joint (Part No.DW-387)

Universal Joint

from

$15.99
DRIVEWORKS Universal Joints are designed to meet or exceed OE fit, form, and function. These universal joints are set to provide superior quality and easy installation. DRIVEWORKS Universal Joints are constructed from quality materials for extended durability. DRIVEWORKS Universal Joints are pre-lubricated with premium grease to provide a longer service life. The grease fittings are pre-installed to allow for easy maintenance (where applicable).

Product Features:
  • The cross is hot forged for the higher torque and horsepower
  • The bearing cups are made by cold forging, having higher strength and better rigidity
  • Bearig cups allow 360 lubricant distribution to bearing surfaces, and are precision-ground for maximum load-carrying capabilities
  • Lubrication grooves designed to ensure grease penetration to entire journal and needle bearings
  • Grease fitting in the cross allows for easy maintenance and the flexible use of the whole assembly
  • Snap rings are held to strict tolerances to ensure proper cup position and retention
  • Nitrile rubber seals to optimize grease retention and reduce contamination
See More

Dorman – Front Drive Shaft: Greaseable, Adjustable, OE Fix (Part No.938-708)

Front Drive Shaft: Greaseable, Adjustable, OE Fix

from

$869.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:
  • Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation.
  • Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance.
  • All-new manufacturing – made 100% new, not remanufactured, so there’s no core charge or return hassle
  • Quality engineering – designed in the United States and backed by decades of automotive aftermarket experience
See More

Autopart International Inc – Wheel Bearing Assemb (Part No.K80052012479API)

Wheel Bearing Assemb

from

$105.65
Wheel Bearing Assemb

AISIN – Differential Shift A (Part No.J70781333983ASC)

Differential Shift A

from

$474.82
Differential Shift A

EMPI – RE CV Joint Boot Kit (Part No.K6010411862EMP)

RE CV Joint Boot Kit

from

$43.68
With Clamps and Grease The EMPIRE CV Joint Boot Kit is an ideal high quality aftermarket replacement that is manufactured to meet or exceed OE specifications for fit, form, and function. Install one boot kit per wheel to restore vehicle to optimal condition and protect the constant velocity joint from contamination

Product Features:
  • Help restore the vehicle to like-new condition
  • Constructed of high strength OE materials
  • Resists environmental contamination
  • Protects the CV joint from premature failure
See More

National – Bearings (Part No.30025)

Bearings

from

$89.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Matched cup and cone components ensures consistent quality and outstanding performance
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV69073)

CV Axle Shaft Assembly

from

$132.99
Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:
  • Designed to meet or exceed OE specifications for fit, form and function
  • 100% new axle and components
  • New axle nut or attaching hardware included when applicable
  • Bearings, races and housings are heat-treated for longer life
  • Precision-engineered seal mating surfaces for leak-free performance
  • High moly CV joint grease with stainless-steel boot bands
See More

Yukon Gear – DiffrlCarrBng (Part No.18110)

DiffrlCarrBng

from

$226.99
DiffrlCarrBng

Yukon Gear – Pinion Depth Shim Kit For Toyota8", GM 7.5", 8.2" & 12 Bolt Truck (Part No.55064)

Pinion Depth Shim Kit For Toyota8", GM 7.5", 8.2" & 12 Bolt Truck

from

$39.99
8″ Toyota, 7.5″ GM, 8.2″ GM, 12T, pinion shim set, & Mazda truck.

Product Features:
  • Pinion depth shim kit for Toyota 7.5″, 8″ and V6
See More

Motive Gear – Differential Pinion Shim Kit (Part No.1109)

Differential Pinion Shim Kit

from

$13.49


Product Features:
  • KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT
See More

Nippon Reinz – Wheel Hub Gasket (Part No.K702363332NRZ)

Wheel Hub Gasket

from

$2.58
The Nippon Reinz Wheel Hub Gasket is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:
  • Premium Original Equipment replacement
  • Provides performance and dependability
  • Manufactured to meet OE specifications
See More

Yukon Gear – RngPnnKt (Part No.24677)

RngPnnKt

from

$468.99
RngPnnKt

Motive Gear – Differential Ring and Pinion (Part No.TAC488IFS)

Differential Ring and Pinion

from

$288.99


Product Features:
  • TOY 10BL 7.5 R/P 4.88 IFS MG FITS 95-04
See More

FEQ – Wheel Bearing (Part No.K8000176163FEQ)

Wheel Bearing

from

$29.52
FEQ wheel bearings are engineered and manufactured to the highest quality standards.

Product Features:
  • Original Equipment Quality
  • Premium modified bearing steel
See More

National – Bearings (Part No.A-5)

Bearings

from

$16.99
National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:
  • Premium bearing design matches OEM specifications
  • Precision manufactured using premium-grade steel for outstanding durability and performance
  • Crowned raceways and rollers to ensure even load distribution for maximum life
  • Industry leading coverage
  • Professional technicians know they can depend on National
See More

Dorman – 4WD Transfer Case Motor (Part No.600-493)

4WD Transfer Case Motor

from

$1043.99
Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:
  • Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications.
  • Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion.
  • 100% new – this transfer case motor is entirely new, not remanufactured like competitors
  • Quality assured – vehicle-specific application has been validation tested to ensure quality
See More

AISIN – Transfer Case Motor (Part No.J7100795240ASC)

Transfer Case Motor

from

$1218.51
Transfer Case Motor

SKF – Input Shaft Seal (Part No.J1156262208SKF)

Input Shaft Seal

from

$16.45
Input Shaft Seal

National – Multi Purpose Seal (Part No.223253)

Multi Purpose Seal

from

$17.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

National – Multi Purpose Seal (Part No.710159)

Multi Purpose Seal

from

$20.99
National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:
  • Low swell in hydrocarbon fluids
  • Design type: spring loaded; multi-lip
  • Provides good low temperature capability
  • Temperature range: -40°F to 225°F; -40°C to 107°C
  • Delivers quality and reliable performance for every type of repair
See More

Upgrade your 2020 Toyota 4Runner with Top-Quality Drivetrains

When it comes to maintaining or upgrading your 2020 Toyota 4Runner, nothing is more important than using high-quality OEM or aftermarket parts that you can trust. Whether you’re repairing damage to your Toyota or enhancing its overall performance, Drivetrains are key to keeping your 4Runner functioning at its best. At Advance Auto Parts, we offer a wide selection of 45 Drivetrains for the 2020 Toyota 4Runner, designed to meet your needs without breaking the bank. From Drive Shafts and Axle replacements to Transfer Cases upgrades, we’ve got you covered with parts that fit your vehicle perfectly and ensure long-lasting performance.

Affordable Prices and Wide Selection

Shopping for Drivetrains for any vehicle can be a hassle, especially if you’re on a budget. But with Advance Auto Parts, you can find high-quality Drivetrains for your 2020 Toyota 4Runner at great prices. Our Drivetrains inventory for this model ranges from just $8.89 to $1,102.99, with an average price of $284.41. Our 45 Drivetrains in stock come from 19 trusted brands, so you’re sure to find the right part for your 2020 Toyota 4Runner without overspending.

Top Brands and High Customer Satisfaction

Advance Auto Parts takes pride in offering only the best brands in the automotive industry. For your 2020 Toyota 4Runner, we stock popular OEM and aftermarket Drivetrains from top names like Valvoline, and more. Valvoline Drivetrains start at just $14.49 and boast an impressive 5 stars average rating from customers. With 168 customer reviews and counting, our 2020 Toyota 4Runner Drivetrains have a strong track record of reliability, ensuring you can trust your purchase.

Explore Related Parts and More

While you’re here, don’t forget to check out other essential categories that go hand in hand with Drivetrain upgrades. Explore related part types like Batteries and Chargers, Oil and Lubricants and more to make sure your 2020 Toyota 4Runner is always ready to roll. We’re committed to providing you with everything you need to keep your 4Runner in top shape, all in one place. Start shopping confidently below for your 2020 Toyota 4Runner!

Best-Selling Drive Shafts and Axles for 2020 Toyota 4Runners

Enhance the driving experience in your Toyota with 14 quality Drive Shafts and Axle components, starting at $14.52.

NSK – Wheel Bearing Assembly (Part No.K8005410854NSK)

Wheel Bearing Assembly

from

$151.77
NSK guarantees the high quality of all of their products by repeated, rigorous bench testing, and other checks that take full advantage of their cutting-edge technology, which only the major bearing manufacturers can offer. Double-row angular or taper contact ball bearing with integral high performance seal. Easy and reliable preload settings and include a simple mounting process with no spacer required. Hub bearings utilize an integral high-performance seal and feature a compact design with no grease packing required. NSK Hub unit bearings are designed to meet increasingly strict requirements that demand lighter weight, greater promotion of fuel efficiency, and enhanced module production systems.

Product Features:
  • Easy and reliable preload setting
  • Easy mounting process
  • No spacer required
  • No grease packing required
  • Compact
  • Integral high performance seal.
See More

Carquest Premium – CV Axle Shaft Assembly (Part No.NCV69170XD)

CV Axle Shaft Assembly

from

$203.99
Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:
  • Designed to meet or exceed OE specifications for fit, form and function
  • 100% new axle and components
  • New axle nut or attaching hardware included when applicable
  • Bearings, races and housings are heat-treated for longer life
  • Precision-engineered seal mating surfaces for leak-free performance
  • High moly CV joint grease with stainless-steel boot bands
See More

Cardone – Drive Shaft: Greasable, Direct Replacement (Part No.65-5032)

Drive Shaft: Greasable, Direct Replacement

from

$617.99
CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:
  • Built to match O.E. form, fit and function.
  • 100% NEW universal joints are installed to ensure proper fit and optimal performance.
  • All slip yokes are lubricated to prevent premature wear.
  • Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.
See More

Dorman – Front Drive Shaft: Greaseable, Adjustable (Part No.938-306)

Front Drive Shaft: Greaseable, Adjustable

from

$602.99
Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:
  • Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance.
  • 100% new – this drive shaft is made from all new components so there’s no core charge or return hassle.
  • Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
  • Serviceable construction – non-staked universal joints are designed for future serviceability
See More

Cardone – Drive Shaft: Greasable, Direct Replacement (Part No.65-5021)

Drive Shaft: Greasable, Direct Replacement

from

$551.99
CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:
  • Built to match O.E. form, fit and function.
  • 100% NEW universal joints are installed to ensure proper fit and optimal performance.
  • All slip yokes are lubricated to prevent premature wear.
  • Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.
See More

Dorman – Rear Drive Shaft: OE Fix (Part No.936-772)

Rear Drive Shaft: OE Fix

from

$471.99
The original drive shafts on specific vehicles have permanently staked universal joints that make servicing difficult. This Dorman OE FIX rear drive shaft makes the U-joints serviceable for simpler maintenance. Every Dorman part is backed by over 100 years of experience, along with a dedicated team of product experts, automotive engineers and technical support specialists based in the United States. We are passionate about giving repair professionals and vehicle owners greater freedom to fix cars and trucks, which is why we have more than 100,000 parts in our catalog today and promise to never stop driving new solutions.

Product Features:
  • Rear Driveshaft Assembly.
  • Rear Drive Shaft: OE Fix.
  • Ready to install – this drive shaft is shipped pre-assembled and factory balanced to ensure immediate smooth operation
  • Simplifies repair – this replacement makes the U-joints serviceable for simpler maintenance
See More

Cardone – Drive Shaft: Greasable, Direct Replacement (Part No.65-5040)

Drive Shaft: Greasable, Direct Replacement

from

$406.99
CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:
  • Built to match O.E. form, fit and function.
  • 100% NEW universal joints are installed to ensure proper fit and optimal performance.
  • All slip yokes are lubricated to prevent premature wear.
  • Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.
See More

Cardone – Drive Shaft: Greaseable, Direct Replacement (Part No.65-5041)

Drive Shaft: Greaseable, Direct Replacement

from

$385.99
CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:
  • Built to match O.E. form, fit and function.
  • 100% NEW universal joints are installed to ensure proper fit and optimal performance.
  • All slip yokes are lubricated to prevent premature wear.
  • Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.
See More

Koyo – Wheel Bearing (Part No.K8000176163KOY)

Wheel Bearing

from

$210.16
Koyo designs, manufacturers and supplies a wide range of hubs and bearings to the world’s leading automotive manufacturers.

Product Features:
  • No need for pre-load adjustment at assembly
  • Increased Load Rating
  • Increased bearing life
  • Equivalent to special re-melting steel GTS (Greater Toughness Steel Bearings)
  • Increased durability and matrix strength by controlling alloy element
  • High resistance against hardness reduction by tempering Installation Note: Some bearings contain active wheel sensors. These wheel sensors normally work together with magnetic ABS sensor rings. These sensor rings have a magnetic north and south poles lying next to each other in its circumference. These magnetic poles must always lie opposite the wheel sensor. If, the wheel bearing is installed improperly, the system wheel sensor and magnetic sensor gear cannot supply a signal making the ABS system inoperable. The ATE Test Card for Magnetic Sensor Gears will assist in prevention of these errors. PN# 760130 ATE
See More

Autopart International Inc – Wheel Bearing Assemb (Part No.K80052012479API)

Wheel Bearing Assemb

from

$105.65
Wheel Bearing Assemb

First Equipment Quality – Wheel Bearing Assembly (Part No.K8005410854FEQ)

Wheel Bearing Assembly

from

$40.91
FEQ designs, manufacturers and supplies a wide range of hubs and bearings to the world’s leading automotive manufacturers.

Product Features:
  • Available in single and double Seals
  • Wide range of bearing selection to choose from
  • No need for pre-load adjustment at assembly
  • No need for lubrication replenishment Increased bearing life
  • High resistance against hardness reduction by tempering
See More

SKF – Axle Shaft Bearing (Part No.K4010469305SKF)

Axle Shaft Bearing

from

$36.21
The SKF Axle Shaft Bearing is an ideal high quality Original Equipment replacement that is manufactured to meet or exceed OE specifications for fit, form, and function.

Product Features:
  • Premium Original Equipment replacement
  • Provides performance and dependability
  • Manufactured to meet OE specifications
See More

FEQ – Wheel Bearing (Part No.K8000176163FEQ)

Wheel Bearing

from

$29.52
FEQ wheel bearings are engineered and manufactured to the highest quality standards.

Product Features:
  • Original Equipment Quality
  • Premium modified bearing steel
See More

Corteco – Wheel Seal (Part No.K8010176118CFW)

Wheel Seal

from

$14.52
Wheel Seal

Most Popular 2020 Toyota 4Runner Transfer Cases

Customize your Toyota with 3 Transfer Cases products like Transmission Transfer Case Motors and Input Shaft Seals, all priced under $1,102.99.

Dorman – 4WD Transfer Case Motor Assembly (Part No.600-423)

4WD Transfer Case Motor Assembly

from

$1102.99
Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:
  • Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications.
  • Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion.
  • 100% new – this transfer case motor is entirely new, not remanufactured like competitors
  • Quality assured – vehicle-specific application has been validation tested to ensure quality
See More

Dorman – 4WD Transfer Case Motor (Part No.600-493)

4WD Transfer Case Motor

from

$1043.99
Transfer case stopped shifting between high and low ranges? Swap out a seized transfer case motor with this direct replacement. Designed to install and perform like the original motor, it uses a factory-style connector and is sealed for protection.

Product Features:
  • Direct replacement – this transfer case motor fits and performs like the original motor on certain vehicle applications.
  • Durable construction – made with factory-style electrical connector and weathertight seal to prevent corrosion.
  • 100% new – this transfer case motor is entirely new, not remanufactured like competitors
  • Quality assured – vehicle-specific application has been validation tested to ensure quality
See More

SKF – Input Shaft Seal (Part No.J1156262208SKF)

Input Shaft Seal

from

$16.45
Input Shaft Seal

Top Picks for 2020 Toyota 4Runner Differentials

Upgrade Toyota 4Runners with top-quality Differentials parts, including 19 OEM and aftermarket selections for your 2020 model.

Valvoline – DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart (Part No.822405)

DEXRON - VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart

from

$14.49
Valvoline DEXRON-VI/MERCON LV ATF is a full-synthetic transmission fluid formulated with advanced additive technology to meet and exceed the requirements of the General Motors DEXRON-VI specification. It is officially licensed and approved by GM and is fully back-serviceable and can be used wherever DEXRON-II and/or DEXRON-III are recommended. Recommended for use in the following applications: DEXRON-VI, DEXRON-III, DEXRON-II, and Allison C-4.

Product Features:
  • Formulated with full-synthetic base stocks and advanced additive technology to meet the challenging demands of automatic transmissions
  • Enhanced anti-shudder protection for smooth shifting and maximum power transfer
  • Developed with anti-wear technology to help improve transmission durability
  • Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Valvoline – DEX/MERC Automatic Transmission Fluid, 1 Gallon (Part No.773636)

DEX/MERC Automatic Transmission Fluid, 1 Gallon

from

$35.99
Valvoline DEX/MERC ATF is a high-quality transmission fluid formulated to meet the challenging demands many automatic transmissions. Its responsive low-temperature fluidity is beneficial in both electronic and hydraulic controlled transmissions and transaxles. Recommended for use in the following applications: MERCON®, DEXRON®-III, Ford M2C138-CJ and M2C166-H, Allison C-4 and TES-389, and Caterpillar TO-2.

Product Features:
  • Formulated with premium base stocks and advanced additive technology to meet the challenging demands of automatic transmissions.
  • Enhanced anti-shudder protection for smooth shifting and maximum power transfer
  • Developed with anti-wear technology to help improve transmission durability
  • Engineered with a proprietary blend of base oils and advanced additives to provide better oil flow at low temperatures and greater film protection at higher temperatures
See More

Valvoline – Transfer Case Fluid, 1 Quart (Part No.855459)

Transfer Case Fluid, 1 Quart

from

$14.99
Valvoline Multi-Vehicle Transfer Case Fluid is a full synthetic product meeting the performance needs for transfer cases recommending Ford XL-12 and GM Auto Trak II specifications or ATF fluids (DEX/MERC, ATF +4, etc).

Product Features:
  • Recommended for use in most Ford, GM and FCA (Dodge, Jeep) models
  • Formulated to help prevent gear wear and protect against rust and corrosion
  • Formulated to deliver enhanced protection against deposits
  • Helps provide better protection during extreme operating conditions
See More

Idemitsu – Type TLS-LV Automatic Transmission Fluid – 1 qt (Part No.30040096-75000C)

Type TLS-LV Automatic Transmission Fluid - 1 qt

from

$14.49
Formulated to meet the specific requirements of Toyota, Lexus, and Scion vehicles equipped with conventional (non-CVT) transmissions that require the use of Toyota ATF WS. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF WS is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:
  • Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
  • Optimized viscosity and advanced friction reducing additive technology provide exceptional fuel economy performance
  • Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
  • Exceptional wear protection of gears and bearings
  • Provides superior deposit control and protects metal surfaces from rust and corrosion
  • Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
See More

Idemitsu – Type TLS-LV Automatic Transmission Fluid – 1 qt (Part No.10114-042B)

Type TLS-LV Automatic Transmission Fluid - 1 qt

from

$12.79
Formulated to meet the specific requirements of Toyota, Lexus, and Scion vehicles equipped with conventional (non-CVT) transmissions that require the use of Toyota ATF WS. Recommended for service-fill in all Toyota, Lexus, and Scion automatic transmissions where ATF WS is specified. Fuel economy demands and more sophisticated electronic controls have made automatic transmissions not only more complex, but also unique to each vehicle manufacturer. Long gone are the days of having just a couple choices of automatic transmission fluid type. IDEMITSU is the factory fill Automatic Transmission Fluid (ATF) supplier to most Asian imports. IDEMITSU application-specific ATF products match the exact friction materials and performance requirements of each different vehicle model for which they are made.

Product Features:
  • Precisely engineered frictional characteristics guarantee smooth shifting and outstanding anti-shudder performance
  • Optimized viscosity and advanced friction reducing additive technology provide exceptional fuel economy performance
  • Excellent resistance to oxidation and thermal breakdown provide long fluid life and extended protection
  • Exceptional wear protection of gears and bearings
  • Provides superior deposit control and protects metal surfaces from rust and corrosion
  • Excellent seal compatibility and conditioning reduces risk of fluid leaks due to seal shrinkage, hardening and cracking
See More

Motive Gear – Differential Pinion Shim Kit (Part No.1109)

Differential Pinion Shim Kit

from

$13.49


Product Features:
  • KIT SHIM TOYO TRK 79-92 REAR/89-92 FRONT
See More

Yukon Gear – Master Overhaul Kit For New Toyota Clamshell Design Front Reverse Rotation Differential (Part No.14130)

Master Overhaul Kit For New Toyota Clamshell Design Front Reverse Rotation Differential

from

$649.99
Yukon Master Overhaul kits give you all the high quality parts you need to start & finish every differential job. Yukon offers more tailor-made kits than any other manufacturer in the industry to meet your specific installation needs. This kit uses premium bearings and races along with high quality seals and small parts. Included in this kit are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), Thread locking compound, and marking compound with brush. Yukon’s Master Overhaul kits are the most comprehensive and complete kits on the market. They do extensive research to ensure that every kit is specially tailored to your application.

Product Features:
  • Fits Toyota 8″ clamshell front
  • Included are Timken bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush, and silicone.
See More

USA Standard Gear – Master Overhaul Kit for New Toyota Clamshell Design Front Reverse Rotation Differential (Part No.37115)

Master Overhaul Kit for New Toyota Clamshell Design Front Reverse Rotation Differential

from

$614.99
USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:
  • Fits Toyota 8″ clamshell front
  • Uses Koyo bearings and races
  • Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, pinion nut, crush sleeve, thread locker, marking compound with brush and silicone.
See More

Yukon Gear – Bearing Install Kit For New Toyota Clamshell Design Front Reverse Rotation Differential (Part No.11108)

Bearing Install Kit For New Toyota Clamshell Design Front Reverse Rotation Differential

from

$569.99
Yukon Bearing installation kits are perfect for shops & builders who have shims on the shelf and are looking to save cost over a Master Overhaul kit. This kit uses high quality bearings and races along with all high quality small parts. kit includes carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve (if applicable), oil baffles and slingers (if applicable), marking compound and brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your ring & pinion set.

Product Features:
  • Fits Toyota 8″ clamshell front
  • Reverse rotation only
  • Included are carrier bearings and races, pinion bearings and races, pinion seal, crush sleeve, marking compound and brush.
See More

Yukon Gear – Ring and Pinion Kit (Part No.24680)

Ring and Pinion Kit

from

$544.99
Ring and Pinion Kit

Yukon Gear – Ring and Pinion Kit (Part No.24681)

Ring and Pinion Kit

from

$544.99
Ring and Pinion Kit

Yukon Gear – High Performance Ring & Pinion Gear Set For Toyota FJ Cruiser Front, 4.56 Ratio, Thick (Part No.24635)

High Performance Ring & Pinion Gear Set For Toyota FJ Cruiser Front, 4.56 Ratio, Thick

from

$529.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.
See More

Yukon Gear – High Performance Ring & Pinion Gear Set For Toyota FJ Cruiser Front, 4.88 Ratio, Thick (Part No.24565)

High Performance Ring & Pinion Gear Set For Toyota FJ Cruiser Front, 4.88 Ratio, Thick

from

$524.99
Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. This is a thick gear for a 3.73 & down carrier. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty.

Product Features:
  • Fits 8″ Toyota clamshell front
  • 8.00″ ring gear diameter
  • 29 spline pinion
  • 10 ring gear bolts
  • 4.88 ratio
  • Thick gear for 3.73 and down carrier
See More

Yukon Gear – RngPnnKt (Part No.24677)

RngPnnKt

from

$468.99
RngPnnKt

Yukon Gear – RngPnnKt (Part No.24679)

RngPnnKt

from

$454.99
RngPnnKt

Yukon Gear – Pinion Install Kit For Toyota Clamshell Design Front Reverse Rotation Differential (Part No.13102)

Pinion Install Kit For Toyota Clamshell Design Front Reverse Rotation Differential

from

$353.99
Yukon Pinion installation kits are a terrific solution for gear installation on lower mileage vehicles where the carrier bearings & races can be reused. This kit uses high quality bearings and races along with a high quality pinion seal and small parts. Included in this kit are the pinion bearings and races, pilot bearing (if applicable), crush sleeve (if applicable), complete pinion shim kit, pinion nut, thread locker, and marking compound with brush. Yukon does extensive research for each application to make sure your kit will arrive with all the correct parts you need to install your pinion gear.

Product Features:
  • Fits Toyota 8″ clamshell front
  • Reverse rotation only
  • Included are pinion bearings and races, pinion seal, crush sleeve, complete pinion shim kit, and marking compound with brush.
See More

Koyo – Differential Bearing (Part No.J7060163891KOY)

Differential Bearing

from

$136.38
Differential Bearing

SKF – Differential Bearing (Part No.J7060163890SKF)

Differential Bearing

from

$88.34
Differential Bearing

SKF – Diff. Side Cover Sea (Part No.J7041183532SKF)

Diff. Side Cover Sea

from

$15.28
Diff. Side Cover Sea

In-Demand Universal Joints for 2020 Toyota 4Runners

Select from 3 premium Universal Joints parts for your 2020 Toyota 4Runner, with prices ranging from $19.40 to $72.43.

Spicer – Universal Joint (Part No.5-1510X)

Universal Joint

from

$62.99
When you see the Spicer name, you know you are buying the highest quality product available. Spicer universal joints are no exception. Dana manufactures a full line of Spicer universal joints that are engineered to ensure longer life for vehicles.
See More

Spicer – Greasable U-Joint (Part No.K1010991371SPI)

Greasable U-Joint

from

$72.43
Spicer Drivetrain Products light-duty U-joints feature journal crosses that are manufactured from high-quality alloy forgings and heat-treated for maximum life. The bearing cups are case-hardened for strength and durability, while the seals are crafted from nitrile rubber for optimum grease retention and contaminant exclusion. Ample grease reservoirs in each trunnion assure effective lubrication; they’re pre-filled with high-quality synthetic lithium grease, providing superior friction-reduction and resistance to higher temperatures. These replacement universal joints are available for dozens of positions, as well as greasable and non-greasable styles. Order the model designed for fitment with your vehicle and engine type.

Product Features:
  • Forged cross
  • Lubeable
  • O.E.M replacement
  • Snap rings
See More

Autopart International Inc – U Joint (Part No.K10101977486API)

U Joint

from

$19.40
U Joint

Most Sold 2020 Toyota 4Runner 4WD Components

Explore our best-selling Toyota parts for the 2020 4Runner among 3 OEM and aftermarket options starting from $448.99.

Dorman – 4WD Axle Actuator Assembly (Part No.600-488)

4WD Axle Actuator Assembly

from

$448.99
This 4WD actuator directly replaces the original equipment part on specific vehicle applications. It is reverse engineered to reliably restore proper functionality.

Product Features:
  • Direct replacement – this 4WD axle actuator directly replaces the original equipment part on specific vehicle years, makes and models.
  • Effective fix – installation addresses inoperative four-wheel drive caused by failed original actuator.
  • Smart solution – delivers reliable fit and function for competitive price
  • Trustworthy quality – backed by team of designers and engineers in the United States
See More

Aisan – Locking Hub Actuator (Part No.K70273342480ASC)

Locking Hub Actuator

from

$566.17
Locking Hub Actuator

AISIN – Differential Shift A (Part No.J70781333983ASC)

Differential Shift A

from

$474.82
Differential Shift A

Top-Rated Drivetrains Brands For Your 2020 Toyota 4Runner

Shop for the best-rated brands offering Drivetrains and other products for your 2020 Toyota 4Runners. Below you’ll find some of our best rated Drivetrains from Valvoline, and more. Drivetrains from these brands that fit a 2020 4Runner start at just $14.49 and are rated as high as 5 stars. OEM and aftermarket Drivetrains don’t get more top quality, durable, and affordable than from the brands below.

Popular Valvoline 2020 Toyota 4Runner Drivetrains

When it comes to maintaining or upgrading your 2020 Toyota 4Runner, using quality Drivetrains is essential to ensure durability and a perfect fit. Valvoline ticks all of those boxes. We offer a wide selection of Valvoline Drivetrains, specifically designed for the 2020 Toyota 4Runner. With over 3 Valvoline brand Drivetrains in stock, you’re sure to find what you need. The prices for these top-notch parts start as low as $14.49, with an average price of just $21.82. Plus, with over 55 customer reviews and an average rating of 5 stars, you can trust that our Valvoline Drivetrains will get the job done right. Choose Advance Auto Parts for reliability, quality, and expert-approved parts that keep your vehicle running strong.

DEX/MERC Automatic Transmission Fluid, 1 Gallon
from
$35.99

(17)

DEX/MERC Automatic Transmission Fluid, 1 Gallon

“Equivalent to oem”

Transfer Case Fluid, 1 Quart
from
$14.99

(36)

Transfer Case Fluid, 1 Quart

“Did not have to use a lot”

DEXRON - VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart
from
$14.49

(2)

DEXRON – VI ATF Full Synthetic Automatic Transmission Fluid, 1 Quart

“I’ve used this in my 2005 2500HD since I bought the truck with 20k on it now at 280k changed every other year maybe 40k I’d put on in two years,
I pu”

FAQs for 2020 Toyota 4Runner Drivetrains

Which Drivetrains are best-sellers for 2020 Toyota 4Runners?

Out of 45 Drivetrains that fit 2020 Toyota 4Runners, the following parts are the top sellers:

What’s the price range for 2020 Toyota 4Runner Drivetrains?

Drivetrain prices for the 2020 Toyota 4Runner start at $8.89 and go up to $1,102.99 for the most premium parts.

What’s the average price of a Drivetrain for a 2020 Toyota 4Runner?

The average price for Drivetrains for the 2020 Toyota 4Runner is $284.41. Keep in mind the variety of part types within our Drivetrain category so you are likely to find a wide range of prices across a variety of parts and components.

Does Advance Auto Parts sell Drivetrains for other Toyota 4Runner model years?

Yes, we currently carry Drivetrains for 40 model years of Toyota 4Runners between 1984 and 2024. Drivetrains are bought most frequently for the following model years: 2023, 2022, 2021, 2019, 2018, 2017, 2016, 2015, and 2014.

What are the cheapest Drivetrains for my 2020 Toyota 4Runner?

The cheapest 2020 Toyota 4Runner Drivetrains we carry in stock are:

What types of Drivetrains do you sell for my 2020 Toyota 4Runner?

Can I get help with 2020 Toyota 4Runner Drivetrain orders?

Contact our customer support team, by chat or phone, through the help desk page, where you can find instant answers about Toyota Drivetrains and more.

What is your return policy for Toyota 4Runner Drivetrains?

Advance Auto Parts keeps returns simple. For new Toyota 4Runner Drivetrains and accessories, your online orders can be returned, in their original condition, within 45 days. For requirements, see the returns page.