from

$108.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to LEXUS 01-20; TOYOTA 01-19;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 2001-2020
Weight approx: 2 Lbs
BEARING ID / BORE: 1.1811 INCH / 30 MM
CENTERLINE: 0.10 INCH / 3 MM
MOUNT WIDTH: 7.00 INCH / 178 MM
STYLE: ROUND FRAME
WITH WINGS

from

$228.02

Rugged SKF drive shaft support bearings are built to meet or exceed OE specifications. They are also built on the years of experience that SKF has earned designing and supplying bearings to the world’s largest OE manufacturers. Engineered and manufactured to specific application requirements that deliver precise drive shaft alignment and support. Center support bearings are pre-lubricated and sealed with metal reinforced seals to prevent contamination. Rubber support cushions are manufactured from durable rubber compounds that provide maximum support while isolating the driveline shaft from damaging vibration. Drive shaft support frames are constructed from high quality steel or aluminum that provides additional strength and long life in harsh environments.

Product Features:

OE Quality, fit and performance
Precise driveshaft alignment and support
Pre-lubricated and sealed
Metal reinforced seals to prevent contamination
Manufactured from durable rubber compounds

from

$94.99

This drive shaft center bearing is designed to match the fit and function of the original bearing on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

Direct replacement – this drive shaft center bearing is designed to match the fit and function of the original bearing on specified vehicles
Restores functionality – this bearing is made to fit and fully restore part functionality after the original bearing fails
Durable construction – this part is made from quality materials to ensure reliable performance and long service life
Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

from

$119.99

Center support bearings or Carrier Support Bearings are used when the driveshaft is split into two sections. It serves as a junction on the drive shaft between the transmission and the differential allowing the driveshaft to flex, relieving stress on other drive line components. Each part is engineered and designed to OE Standards. Applicable to LEXUS 99-20; TOYOTA 01-20;. Please verify your application.

Product Features:

MAXIMUM VIBRATION DAMPENING: Rubber cushion is made of high grade rubber that ensures maximum dampening of vibration and the ability to absorb over loads.
HEAVY GAUGE STEEL FRAME: The housing frame is made from heavy gauge steel with durability that extends the service life.
READY TO INSTALL: Most center supports include a sealed bearing and dust shield and are ready to install.
For Years: 1999-2020
Weight approx: 2 Lbs
BEARING ID / BORE: 1.1811 INCH / 30 MM
CENTERLINE: 0.10 INCH / 3 MM
MOUNT WIDTH: 7.00 INCH / 178 MM
STYLE: ROUND FRAME
WITH WINGS
WITH ELEVATED MOUNTING PLATFORM

from

$16.99

Axle Shaft Seal

from

$109.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$104.99

N

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$205.15

Axle Assembly

from

$103.99

Carquest Premium constant velocity (C.V.) axle shaft assemblies are 100% new units that are designed to meet or exceed OE specifications. Every part number is tested to guarantee a proper fit and reliable performance. Carquest Premium CV axles are assembled with a specially formulated high-temperature moly grease to resist friction and wear of the bearings and joints. Our strict engineering and quality specifications ensure a long-lasting repair that is guaranteed with an industry-leading warranty.

Product Features:

Designed to meet or exceed OE specifications for fit, form and function
100% new axle and components
New axle nut or attaching hardware included when applicable
Bearings, races and housings are heat-treated for longer life
Precision-engineered seal mating surfaces for leak-free performance
High moly CV joint grease with stainless-steel boot bands

from

$95.99

Manufactured to be an OE replacement, CV axles use 100% new materials and are engineered for ease of installation and long service.

Product Features:

All New Materials
Engineered for OE Fitment
-40 Degree Rated CV Boots
Moly-Blend Grease in inner and outer joints
New nut and mounting hardware included if required

from

$1257.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$1676.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$1169.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$818.99

CARDONE Remanufactured Prop Shafts are engineered using the most stringent quality processes to deliver smooth, consistent performance in any driving condition. Original designs are scrutinized for potential improvement, and where applicable, design upgrades are implemented to produce a more durable part than the original. All critical components are tested to ensure proper function. Additionally, all CARDONE Prop Shafts are 100% dynamically balanced, resulting in vibration-free performance at all speeds.

Product Features:

Built to match O.E. form, fit and function.
100% NEW universal joints are installed to ensure proper fit and optimal performance.
All slip yokes are lubricated to prevent premature wear.
Units are 100% dynamically balanced at 3200 RPMs for vibration-free operation and increased joint life.

from

$1185.99

Replacing a drive shaft doesn’t have to be complicated. This complete drive shaft assembly is pre-balanced and ready to install with 100% new yokes, tubes, constant velocity (CV) joints and universal joints.

Product Features:

Direct replacement – this drive shaft is made to the original equipment dimensions for dependable fit and performance
100% new – this drive shaft is made from all new components so there’s no core charge or return hassle
Ready to install – this drive shaft arrives pre-balanced to make installation quick and simple
Serviceable construction – non-staked universal joints are designed for future serviceability

from

$41.49

National® has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

Designed to repair damaged, grooved or worn shafts
Durable stainless steel construction for corrosion-free sealing surface that surpasses most original shaft specifications
Ideal for a shaft where indications of seal wear, such as tracks or grooves have developed
Ultra-thin construction (0.01/0.25mm wall thickness) allows original seal size to be used with minimal additional lip loading
Easy to install with removable flange and installation tool
Installation tool reduces sleeve distortion and allows for installation without removal from the shaft