2018 Chevrolet Silverado 1500 Differentials

Motive Gear Differential Bearing Kits Include Front & Rear Pinion Bearing, Pinion Seal, Carrier Bearings, Pilot Bearing Where Applicable, Gear Marking Compound, Crush Sleeve, Pinion Nut, Brush, Thread Locking Compound And Cover Gasket Or Rtv

Product Features:

• GM 10 BOLT 8.5 BRG MSTR KIT W/EATON OR AUBURN PRO TIMKEN

Pennzoil? Synchromesh Fluid is designed to offer optimal protection for moderately loaded gears in manual transmissions. Containing a high detergent additive system, it helps cope with water, dust, dirt, and any other small deposits you might encounter on or off-road(1). Pennzoil? Synchromesh Fluid also offers synchronizer compatibility for performance in manual transmissions, specifically to fulfill the needs of Chrysler, GM, Honda and other transmission requirements. Pennzoil? Synchromesh Fluid meets General Motors specification 9985648 for use where GM part numbers 12345349 or 12345577 are called out for use. Chrysler manual transmission fluid specification MS-9224 is also met. This high quality manual transmission fluid is formulated for good low temperature flow to maintain shift characteristics even after a cold night(2). Corrosion protection is added to help protect your transmission. Pennzoil? Synchromesh fluid is a manual transmission fluid designed for certain manual trans axles and manual transmissions used by general motors or Chrysler. (1)The Anglamol 6091 additive system contains approximately twice the sulfonate detergent levels as current generation PCMO, 4500 ppm as magnesium of magnesium sulfonate. This engine oil type additive will emulsify water and polar contamination sufficiently to handle contamination levels above 0.5% water. Anglamol 6091 – Detergent, friction modifier, extreme pressure agent, seal swell, anti-wear, anti-oxidant. Chemical Composition – Magnesium sulphonate, alkenyl amide, alkenyl ester sulphide, alkenyl phosphite, alkylbenzene, hecterocyclic ether, zinc dithiophosphate. (2)Pour point is less than -39 Deg. C. Low temperature viscosity in a -40 Deg. C Brookfield test of 50,000 cPs maximum, less than a 75W gear oil and the cold cranking viscosity less than a typical conventional SAE 5W engine oil.

Product Features:

• Excellent yellow metal compatibility
• Meets GM specification 9985648 and Chrysler specification MS-9224
• Excellent synchronizer performance
• Exhibits excellent low-temperature performance

Pro-King is the leading supplier of transmission and driveline products in the aftermarket.

Product Features:

• All products are designed to meet or exceed OE quality, form, fit and funtion.

Motive Gear offers some of the toughest drive train components on the market today. If you are looking for the largest line of performance ring and pinion gear options available with gear sets in a wide range of ratios for nearly every application, both o

This axle differential seal is designed to match the fit and function of the original seal on specified vehicles, and is engineered for durability and reliable performance.

Product Features:

• Direct replacement – this axle differential seal is designed to match the fit and function of the original seal on specified vehicles
• Restores functionality – this seal is made to fit and fully restore part functionality after the original seal fails
• Durable construction – this part is made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Yukon yoke for GM 8.25″ IFS and 9.25″ IFS (mech 3R). 2.556″ snap ring span, 1.125″ cap diameter. Inside snap ring. This yoke uses inside snap rings. All Yukon yokes come with a one year warranty against manufacturing defects.

Product Features:

• Fits GM 8.25″ IFS and 9.25″ IFS
• 30 spline
• Mechanics 3R u-joint size
• Inside snap ring design
• 2.556″ snap ring span
• 1.125″ cap diameter
• Strap style

MOOG premium control arms for foreign and domestic nameplates are engineered for structural strength and corrosion protection.

Product Features:

• EASY TO INSTALL — Precision tolerances for easy installation and steering alignment giving you a perfect fit right out of the box
• HIGHLY PRECISE ENGINEERING — Optimized bushings for quiet operation and resistance to wear, salt, road grime and oils
• COMPREHENSIVE COVERAGE — Available for foreign and domestic nameplates
• Construction and design validated by MOOG engineers
• Incorporates proven design and engineering features

GM 8.6″ 30 spline standard open loaded carrier. Complete differential case with internals.

Product Features:

• Standard open carrier case and spiders
• Fits GM 8.6″

This differential housing is a direct replacement for an original unit that has failed due to impact, normal wear, insufficient lubrication, or damaged internal components. It is made of durable materials for reliable service..

Product Features:

• Ideal solution – this differential housing is a direct replacement for an original unit that has failed due to impact, normal wear, insufficient lubrication or damaged internal components.
• Exact fit – matches the fit, function and performance of the original differential housing on specified vehicles
• Durable construction – the housing and its internal components are made from quality materials to ensure reliable performance and long service life
• Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

• Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
• Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
• Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
• Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

Product Features:

• GM9.5″ INTERNAL KIT (OPEN) 33 SPL. FRONT & REAR

By constantly introducing design enhancements that extend product life and simplify installation and replacement, MOOG has earned its reputation as the chassis industry’s Problem Solver.

Product Features:

• Easy to install
• Returns like-new steering
• Long-lasting performance
• Construction and design validated by MOOG engineers
• Incorporates proven design and engineering features

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.

Yukon 1541H replacement alloy right hand rear axle for Dana 44 HD with 3.5″ ABS ring, a length of 29-3/8 inches, and 30 splines. Yukon 1541H alloy axles offer a strength increase over stock while retaining a low cost. Yukon 1541H alloy rear axles come with a one year warranty against manufacturing defects. This is a C-clip axle.

Product Features:

• 1996-1999 Jeep Grand Cherokee with Dana Spicer 44HD
• Right hand side
• 30 spline
• 29 3/8″ long
• Includes ABS ring

Remanufactured Rear Axle assemblies are completely disassembled, thoroughly cleaned and reassembled using new wear parts. Units are assembled, sealed & include backing plates, axle shafts & fluid.

Product Features:

• Rear axles are assembled with backing plates & axle shafts, and filled with fluid prior to shipping
• Axles are fully painted & shipped securely in environmentally safe and recyclable containers that are the perfect size for returning your original core
• Our complete Rear axle assemblies mean you just hang brakes, connect suspension & go! Your installation will be simple and trouble free
• Remember to match axle ratio to original. For 4WD rear axle must match front axle ratio

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

National has built a reputation as one of the most respected names in the industry. We have offered premium sealing solutions for more than 75 years. Our design team keeps pace with the industry and provides advanced solutions for today’s vehicles.

Product Features:

• Low swell in hydrocarbon fluids
• Design type: spring loaded; multi-lip
• Provides good low temperature capability
• Temperature range: -40°F to 225°F; -40°C to 107°C
• Delivers quality and reliable performance for every type of repair

Yukon Ring & Pinion sets give you the confidence of knowing you’re running gears designed for the harshest of conditions. Whether it’s on the street, off-road, or at the track; Yukon ring & pinion sets deliver unrivaled performance & quality. Yukon uses the latest designs and manufacturing technologies to provide a quiet running gear that is strong and easy to set up. All Yukon ring & pinion sets come standard with a one-year warranty. This gear set does not have an ABS provision on the pinion.

Product Features:

• Fits GM 8.5″ and 8.6″
• 8.50″ ring gear diameter
• 30 spline pinion
• 10 ring gear bolts
• 3.08 ratio

8.5, 9.5, & 8.2 Buick, Oldsmobile, Pontiac GM REDI sleeve yoke saver.Yukon Mighty seal.

Product Features:

• Pinion Redi-sleeve
• Fits GM 8.5″, 9.5″ and 8.2″ Buick, Oldsmobile and Pontiac

Differential Cover G

Fel-Pro gaskets offer 100% vehicle sealing with application-specific materials to give you sealing solutions with the performance and durability professionals trust

Product Features:

• Meets or exceeds all original equipment specifications
• Application specific design to ensure a perfect fit
• Unsurpassed quality you can trust
• Validated for fit, form and function
• Each Fel-Pro gasket, no matter how small, is engineered to exacting standards with proprietary design, engineering and manufacturing processes

USA Standard Master Overhaul kits let you finish your install with confidence. This kit uses Koyo bearings and races. Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve (if applicable), oil baffles and slingers (if applicable), threading locking compound, marking compound with brush and gasket.

Product Features:

• Fits 1999-2008 GM 8.6″
• Uses Koyo bearings and races
• Included are carrier bearings and races, pinion bearings and races, pinion seal, complete shim kit, ring gear bolts, pinion nut, crush sleeve, thread locker, marking compound with brush and gasket.

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Crowned raceways and rollers to ensure even load distribution for maximum life
• Industry leading coverage
• Professional technicians know they can depend on National

8.75-42, 8.75-89, 9.25″ Chrysler & GM, 9.5″, 10.25″ pinion shim kit.

Product Features:

• Pinion depth shim kit for Chrysler 8.75″ with ’42’ or ’89’ case housing, Chrysler 9.25″, GM 9.5″ and Ford 10.25″

This direct replacement differential cover matches the fit and function of the original equipment diff cover for a reliable, leak-free repair. It features a durable design, made to strict specifications, to help ensure reliable service life.

Product Features:

• Direct replacement – this differential cover matches the fit and function of the original equipment diff cover on select vehicles
• Reliable repair – the smart solution for fixing an existing cover that’s rusted, damaged or leaking differential fluid
• Durable construction – this differential cover is made according to strict engineering standards to help ensure dependability
• Trustworthy quality – backed by a team of product experts in the United States and more than a century of automotive experience

National Oil Seals & Bearings offer a full line of premium oil seals and bearings.

Product Features:

• Premium bearing design matches OEM specifications
• Precision manufactured using premium-grade steel for outstanding durability and performance
• Premium seal design keeps out dirt and contaminants and retains lubrication in bearing
• Integral ABS encoder seal where applicable
• Professional technicians know they can depend on National

Product Features:

• MINI INSTALL KIT GM8.2IFS 98 & ON

Richmond Gear is the leading manufacturer of professional quality, high-performance drivetrain products. Our complete line of products ranges from high performance ring-and-pinion sets for serious street and racing applications to torque-hungry manual transmissions and components. Richmond Gear products have been winners both at the Daytona 500 and U.S. Nationals for decades. WINNERS RUN RICHMOND!

Product Features:

• For over 80-years, the Richmond Double-Diamond logo has represented some of the highest quality gears in the racing industry. Winners Run Richmond!
• The superior quality of Richmond gearsets is a result of outstanding design, world class manufacturing and an extensive testing process that is performed on all products.
• Richmond performance gearsets have been winners for decades at: NHRA, NMRA, NMCA, Daytona 500, WISSOTA and U.S. Nationals.
• Richmond Gear is a leading manufacturer of high performance ring and pinion gearsets and drivetrain components, backed by a two year warranty.
• Engineered to perform faster and be more reliable, Richmond performance drivetrain products are the result of a continuous research and development program combined with state-of-the-art manufacturing capabilities.