2015 Subaru Legacy Belts and Hoses
More 2015 Subaru Legacy Belts and Hoses Categories
If you’re looking for an original Belts and Hoses replacement for a 2015 Subaru Legacy, you can search through our selection below. You’ll also find aftermarket and OEM Belts and Hoses to meet your needs.
Essential 2015 Subaru Legacy Belts and Hoses
Gates – Molded Heater Hose: EPDM, Direct Fit, 0.62" Inside Diameter (Part No.18081)
from
$25.99
Gates Small I.D. Molded Coolant Hose is factory-molded, OEM style hose to fit today’s smaller, tighter-fitting engine compartments. Can be used for coolant, water and air applications. Approved for marine applications.
Product Features:
See More
Product Features:
- Has all the quality features of Gates molded coolant hose and similar to OEM specifications
- Engineered to resist electrochemical degradation – the leading cause of hose failure
- EPDM tube, synthetic fiber knit reinforcement, EPDM cover
- Meets SAE 20R3 Type EC Class D-1 and D-2 specifications
- Temperature Range: -40 Deg. F to 275 Deg. F (-40 Deg. C -135 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Molded Heater Hose; EPDM Rubber, 5/8 Inch Diameter, 14 1/4 Inch Length (Part No.87649)
from
$11.79
Providing reliable service in applications requiring molded hoses in small diameters, the Dayco small I.D. heater hose is designed to replace OEM coolant hoses. Made with the same bends and routing as the original assembly, this molded hose is meant to fit the vehicle precisely. The knitted reinforcement and synthetic EPDM construction provide high-strength performance and resistance to detrimental environmental elements, coolants and temperature variations of -40°F (-40°C) to +257°F (+125°C) and the “quick connect” end allows for fast, convenient installation.
Product Features:
See More
Product Features:
- Meets the requirements of SAE J20R3, Class D-1
- Designed to meet Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Engineered as an OEM replacement
- The knitted polyester reinforcement provides high burst strength and resists degradation from temperature extremes and moisture
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.50" Diameter (Part No.B70081)
from
$24.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Gates – Vulco-Flex½ II Flexible Coolant Hose (Part No.25474)
from
$26.99
Product Features:
See More
- Improved sealing surface for greater leak resistance
- High flexibility for easy installation
- Maximum vehicle coverage with minimum inventory
- Resistant to heat, oil and ozone
- Rated for SAE 20R5 Class D-2 performance
- Temperature Range: up to +257 Deg. F (+125 Deg. C)
- Note: Gates recommends replacing clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 10.5" Long, 1.50" Diameter (Part No.C72531)
from
$28.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Molded Radiator and Bypass Hose (Part No.G2000401239DAY)
from
$14.08
Designed to replace original equipment manufacturer hose, Dayco Molded Radiator and Bypass Hose are built with knitted reinforcement and EPDM construction which provides high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. The Dayco Molded Radiator and Bypass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro- chemical requirements as specified in SAE J1684.
Product Features:
See More
Product Features:
- Made with synthetic EPDM rubber compounds that provide resistance to deterioration from ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C)
- The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose
- Meets SAE J20R4, Class D-1 requirements for improved service hose
- Meets Type EC electro-chemical requirements as specified in SAE J1684; which eliminates premature deterioration of the inner tube caused by the build up of static electric charges
Gates – Premium Molded Coolant Hose (Part No.21404)
from
$19.99
Gates Molded Coolant Hose is manufactured to fit specific applications. Similar to OEM specifications. Approved for marine applications.
Product Features:
See More
Product Features:
- Specifically-engineered materials resist collapse under vacuum
- Engineered to resist electrochemical degradation, the leading cause of hose failure
- Pre-shaped to fit and to ensure perfectly sealed conditions
- EPDM tube: synthetic fiber knit reinforcement: heat-, ozone- and chemical coolant-resistant EPDM cover
- Meets requirements of SAE 20R4, class D2 and DIN 73411, class A (except for tolerances)
- Temperature Range: -40 Deg. F to +257 Deg. F (-40 Deg. C to +125 Deg. C)
- Note: Gates recommends replacing hose clamps each time a new coolant hose is installed
- Caution: Do not use for fuel or oil transfer applications
INA – Accessory Belt Tensioner Assembly (Part No.G6001279822INA)
from
$115.82
The INA Accessory Belt Tensioner Assembly is a direct fit OEM replacement that contains the same high quality craftsmanship and materials as the original equipment it replaces.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application
- High quality precision spring tension assembly
- OE specified bearing and pulley assembly
- Durable long life performance
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999593A)
from
$99.99
This Heavy duty belt tensioner is manufactured by one of the largest original equipment tensioner suppliers to ensure proper fit and performance. This tensioner is produced for serpentine belt routing applications and is made of high strength steel for improved life and durability. This part corresponds to the 2010-2013 Subaru Outback,Legacy with 2.5L. The tensioner maintains the O.E. round spring technology as well as the internal damping design specified for this application. This higher damping consequently reduces arm motion and wear as well as an optimized install feature for ease on tensioner replacement. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Litens – Serpentine Belt Tensioner: 1 Piece (Part No.999422A)
from
$99.99
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and is made of high strength steel for improved life and durability. This pulley conforms to original equipment material, tolerances, and specifications. This part fits 2008-2013 Subaru Tribeca, Legacy, Outback with 3.6L. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 80 mm Diameter (Part No.900652A)
from
$48.49
This Litens supplied pulley is manufactured by the original equipment (O.E.) manufacturer. This part is specifically designed for Scion / Subaru / Toyota applications. Heavy duty steel pulley construction ensures long life and trouble-free performance. This pulley meets or exceeds all original equipment fit, form, and performance characteristics. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
Product Features:
See More
Product Features:
- Heavy duty steel pulley construction
- OE-spec sealed ball bearings with synthetic grease and double lip seals for long life
- Installation instructions included
- Heavy duty polyacrylic seals and synthetic grease for added enhanced durability
- Installation instructions included
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter (Part No.900043A)
from
$55.99
This Litens pulley is manufactured by one of the largest original equipment pulley suppliers to ensure proper fit and performance. This pulley is produced for serpentine belt routing applications and conforms to original equipment material, tolerances, and specifications. This replacement part is made in the U.S.A. to the O.E. specified design and meets all performance and durability requirements. Heavy duty steel construction. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Dorman – Idler/Tensioner Pulley: Specific Fit, Steel, 80 mm Diameter (Part No.419-693)
from
$44.49
This replacement accessory drive belt idler pulley has been engineered to match the function and performance of the original pulley on select vehicle years, makes and models, properly restoring critical vehicle operations.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt idler pulley matches the fit and function of the original equipment pulley on specified vehicles
- Restores performance – fixes a failed, squealing or groaning noise from a worn idler pulley
- Application specific – reverse engineered from the original design on certain vehicle years, makes and models
- Trustworthy quality – backed by team of engineers and quality specialists in the United States
Dayco – Poly Rib Belt Serpentine Belt; 67.91 Long, 6 Rib Count (Part No.5060680)
from
$43.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mile
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Poly Rib Belt Serpentine Belt; 62.6 Long, 6 Rib Count (Part No.5060625)
from
$32.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
- Made in the USA
Dayco – Poly Rib Belt Serpentine Belt; 33.27 Long, 4 Rib Count (Part No.5040333)
from
$35.99
Constructed with aramid reinforced EPDM compounds, the Dayco poly-V serpentine belt delivers more than just OE quality. Developed through extensive laboratory and road testing, the rib profile in this EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and helps eliminate noisy belt conditions. Dayco poly rib serpentine belts offer extensive flexibility and longer service life, while handling higher workloads and temperatures.
Product Features:
See More
Product Features:
- Provides full coverage for today’s light-duty vehicle market, especially vehicles with troublesome drives
- Engineered to help address noise issues caused by the belt drive
- Capable of handling more extreme temperatures and workloads
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16.5" Long, 1.50" Diameter (Part No.E72484)
from
$31.99
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Curved Radiator Hoses: EPDM Rubber, Standard Duty, 8.25" Long, 1.06" Diameter (Part No.B71153)
from
$15.79
The Dayco curved radiator hose features knitted reinforcement, a protective sleeve and a synthetic EPDM rubber construction for high-strength performance, protection against abrasion and resistance to oil, mud, salt, road debris, ozone and coolants. It can also withstand temperature variations of -40 Deg. F (-40 Deg. C) to +257 Deg. F (+125 Deg. C). The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose.
Product Features:
See More
Product Features:
- Meets SAE J20R4, Class D-1 requirements
- Meets Type EC electro-chemical requirements as specified in SAE J1684, which prevents inner tube deterioration caused by the build-up of static electric charges
- Provides excellent protection against external elements
Dayco – Molded Radiator and Bypass Hose (Part No.G2000537507DAY)
from
$13.08
Designed to replace original equipment manufacturer hose, Dayco Molded Radiator and Bypass Hose are built with knitted reinforcement and EPDM construction which provides high strength and resistance to oil, mud, salt, road debris, ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C) that are required for OEM hose replacements. The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose. The Dayco Molded Radiator and Bypass Hose has a convenient plastic hang strap for quick and easy merchandising. In addition to meeting SAE J20R4, Class D-1 requirements, this hose is now designed to meet Type EC electro- chemical requirements as specified in SAE J1684.
Product Features:
See More
Product Features:
- Made with synthetic EPDM rubber compounds that provide resistance to deterioration from ozone, coolants, and temperature variations of -40F (-40C) to +257F (+125C)
- The inner base tube is reinforced with knitted rayon for maximum strength and burst resistance for the life of the hose
- Meets SAE J20R4, Class D-1 requirements for improved service hose
- Meets Type EC electro-chemical requirements as specified in SAE J1684; which eliminates premature deterioration of the inner tube caused by the build up of static electric charges
Bando – Multi Rib (Serpentine) Belt (Part No.W100026288BAN)
from
$12.26
Bando USA has been a leading OE supplier to automotive manufacturers for over 50 years and Bando serpentine belts are original equipment on over 70% of the top 10 selling vehicles in North America. Bando USA will not compromise on critical quality measurements. Bando belts are produced to the same, more precise OE metric size to deliver an exact fit within the millimeter, ensuring a perfect fit every time. In addition to exact metric sizing, Bando USA aftermarket serpentine belts provide true OE performance for its aftermarket belts, as they are produced on the same manufacturing lines as the OE belts. Installation Note: The manufacturer recommends checking and/or replacing idler and tensioner bearings when replacing the serpentine belts
Product Features:
See More
Product Features:
- OE-Equivalent.
- Direct fit for easy installation.
- Resistant against wear, oil and heat.
- Strong tensile cords limit stretching.
- Supports higher horsepower loads.
- Made from high strength synthetic rubber.
Dayco – Poly Rib Serpentine Belt (Part No.W1000323031DAY)
from
$55.27
Built for passenger cars and light-duty trucks, Dayco’s extensive line of Poly Rib serpentine belts are engineered for high mileage, demanding drives found in today’s vehicles. As the manufacturer of the first original equipment multi-ribbed serpentine belt, Dayco’s commitment to automotive product excellence and innovation is unwavering. The Dayco Poly Rib W Profile serpentine belt is the most innovative advancement in serpentine belt design in more than 30 years. Developed through extensive laboratory and actual road mileage testing, this unique rib profile EPDM belt has been engineered to conform to high mileage, worn or misaligned drives and help eliminate noisy belt conditions. Constructed with aramid-reinforced EPDM compounds, the Dayco W Poly Rib serpentine belt delivers more than just OE-required quality. It delivers the solution to troublesome drive problems.
Product Features:
See More
Product Features:
- Constructed with aramid-reinforced EPDM compounds
- Engineered to conform to high mileage, worn or misaligned drives
- Helps eliminate noisy belt conditions Related Documents: (PDF 63.78 KB)
Bando – Drive Belt (Part No.W1000382843BAN)
from
$29.80
Bando has been manufacturing rubber products for over 100 years. Bando is the OEM supplier to over 80 percent of the top 10 cars sold in the U.S. (by volume). Bando belts are made with EPDM rubber which adheres to OEM specification that is more heat resistant and long lasting. With 19 plants worldwide, Bando are the 3rd largest manufacturer of automotive drive belts in the world. Bando’s automotive belts, serpentine, timing and V-belts are engineered to meet the unique requirements of today’s high performance engines for applications that run the gamut from international racing teams to light duty trucks. Bando manufactures belts for the world’s leading automakers, supplying both OEM and aftermarket applications, all to the same exacting standards of quality.
Product Features:
See More
Product Features:
- Designed to provide the positive no-slip drive requirements needed on demanding overhead cam applications
- Precision molded teeth are protected by durable fabric facing for long life
- Tensile cord is engineered and tested for maximum load carrying capabilities
- Rubber backing resists abrasion, oil and heat
Dorman – Coolant Pipe For Oil Cooler (Part No.626-594)
from
$38.99
This engine oil cooler hose assembly matches the fit and function of the original equipment components for reliable repair and restoration of proper oil circulation between the oil cooler and engine.
Product Features:
See More
Product Features:
- Ideal replacement – this engine oil cooler hose assembly is a direct replacement for the original hose assembly
- Quality materials – this engine oil cooler hose assembly is made from corrosion-resistant materials to ensure the smooth transfer of oil from the engine to the cooler
- Easy to install – no special tools required
- Quality tested – rigorous quality control ensure this hose assembly conforms to product standards
Imperial – Metal Line Kit for Engine Oil Coolers (Part No.240293)
from
$79.99
Metal line kit for engine oil coolers. Routes oil lines past exhaust manifolds.
Product Features:
See More
Product Features:
- Metal line kit
- For use in engine oil cooler applications
- Routes oil lines past exhaust manifolds
- Provides protection where standard hoses can fail
Imperial – 1/2" x 12′ Engine Oil Cooler Hose (Part No.240112)
from
$48.49
1/2″ x 12′ engine oil cooler hose. Imperial engine hose is specifically designed for engine cooling applications.
Product Features:
See More
Product Features:
- Engine oil cooler hose
- Size: 1/2″ x 12′
- Designed for engine oil applications
- 12′ hose length accommodates most applications
Litens – O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 70 mm Diameter (Part No.900547A)
from
$32.99
This part is specifically designed for Pontiac, Scion, Subaru, and Toyota applications. Heavy duty steel pulley construction ensures long life and trouble-free performance. This pulley meets or exceeds all original equipment fit, form, and performance characteristics. For maximum performance and durability, always use genuine Litens components. Litens is the world’s largest supplier of original equipment (O.E.) power transmission products. At Litens, we design systems that are more efficient, resulting in tangible fuel economy/emissions benefits. Litens holds over 2000 patents and continues to respond to the ever-changing automotive industry by investing heavily in new technology, facilities, and people. 90% of our line is made of products coming from the OE manufacturer, which makes the Litens Tensioning Products portfolio the purest OE tensioning line in the North American aftermarket.
See More
Dayco – Dayco, Acc. Belt Tension Pulley (Part No.G60111330434DAY)
from
$12.80
The Dayco Accessory Belt Idler Pulley is a direct fit OEM replacement that contains the same high quality craftsmanship as the original equipment it replaces.
Product Features:
See More
Product Features:
- OE-Equivalent and a direct fit application.
- Precision bearing
- OE High quality pulley assembly
- Durable long life performance.
Dorman – Idler Pulley (Pulley Only) (Part No.419-633)
from
$45.99
This accessory drive belt tensioner pulley is designed to match the fit and function of the original pulley on specified applications. Made of quality materials, it is engineered for reliable performance and durability.
Product Features:
See More
Product Features:
- Direct replacement – this accessory drive belt tensioner pulley is designed to match the fit and function of the original pulley on specified applications
- Restores functionality – reliable replacement for an original pulley that has failed due to vibration or corrosion
- Durable construction – this part is made from quality materials to ensure reliable performance and long service life
- Trustworthy quality – backed by team of product experts in the United States and more than a century of automotive experience
Popular 2015 Subaru Legacy Belts and Hoses Categories
2015 Subaru Legacy Belts and Hoses
You count on your 2015 Subaru Legacy to run right. That means taking care of it with regular maintenance, necessary repairs, and the right parts. Advance Auto Parts can help with all of that thanks to our extensive inventory of trusted Belts and Hoses. With 25 Belts and Hoses ranging in price from $1.49 to $165.46, you’re sure to find everything you need for your 2015 Subaru Legacy.
Brands matter. If you want to shop a specific Belts and Hoses brand, we stock 8 different brands like Dayco, Litens, and Imperial. 2015 Subaru Legacy Belts and Hoses start as low as $1.49!
One of the best ways to find top quality OEM or aftermarket Belts and Hoses is by asking professionals. Short of that, you can shop with confidence thanks to our 85 extensive product reviews on 2015 Subaru Legacy Belts and Hoses. Some of the top-rated Belts and Hoses products we carry are O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 80 mm Diameter with 5.0 stars.
Did we mention you can order your Belts and Hoses from our online catalog and have them shipped right to your garage? Or, if you feel like seeing the parts first-hand, search for your nearest Advance Auto Parts location above and pick up in-store when you’re ready. Browse our full Belts and Hoses inventory for your 2015 Subaru Legacy below to get started!
Top-Rated Belts and Hoses Brands For Your 2015 Subaru Legacy
Trusted Belts and Hoses OEM and aftermarket product brands are what Advance Auto Parts specializes in. The brands we work with are sure to keep that 2015 Subaru Legacy running right for years to come. In our inventory you’ll find brands like Dayco, Litens, Imperial, and even more.
Popular Driveworks Belts and Hoses
You’ll find popular Driveworks brand products across Serpentine and V Belts. All are waiting to get your 2015 Subaru Legacy back on the road. Some of the top-rated Driveworks products in these categories are:
Top-Rated Dayco Belts and Hoses
If Dayco are what you’re looking for, our inventory holds plenty. We stock Dayco brand Belts and Hoses for your 2015 Subaru Legacy, and some of our most reviewed Dayco parts include:
from
$24.99
(16)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 12" Long, 1.50" Diameter
Lower Radiator Hoses
from
$31.99
(6)
Curved Radiator Hoses: EPDM Rubber, Standard Duty, 16.5" Long, 1.50" Diameter
Upper Radiator Hoses
FAQs for 2015 Subaru Legacy Belts and Hoses
What are the most purchased Belts and Hoses for the 2015 Subaru Legacy?
Out of 25 Belts and Hoses for the 2015 Subaru Legacy, the most popular in our inventory are:
from
$48.49
This product is not rated
O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 80 mm Diameter
Idler Pulleys
from
$25.99
This product is not rated
Poly Rib Belt Serpentine Belt; 42.52 Long, 6 Rib Count
Serpentine Belts
What are the top-rated 2015 Subaru Legacy Belts and Hoses?
Top-rated Belts and Hoses for your 2015 Subaru Legacy based on customer reviews/ratings are:
from
$35.99
(1)
O.E Quality Idler/Tensioner Pulley: Direct Fit, Steel, 80 mm Diameter
“Perfect part to assist with degree timing”
