from

$29.99

The Engine Coolant Temperature Sensor determines the exact temperature of the engine coolant by sending an analog signal to the ECM to censure proper air/fuel ratio along with proper operation of the cooling fan(s) and temperature gauge. The Engine Coolant Temperature Sensor may be located on the cylinder head, engine block, thermostat housing or intake manifold. Reasons for replacement include: check engine light illumination, erratic or no temperature gauge operation, erratic or no cooling fan operation, and engine overheating.

Product Features:

OE MATCHED: Wires and probe length match OE. Mounting clip(s) included where applicable
FASTER RESPONSE TIME: Thermal conductive grease inside brass housing increases sensor response time
THE NTK DIFFERENCE: Thread sealant/o-ring installed where applicable. Thermistor placement within the housing matches OE to ensure proper output. Proper thermal conductive grease to provide accurate temperature transfer to the thermistor

from

$22.14

Water Temp. Sensor

from

$64.99

Beck/Arnley parts meet foreign nameplate OE specifications for form, fit and function. Our product specialists work with a network of global sourcing partners so you can install the right part with confidence.

Product Features:

Matches OE form, fit and function
Manufactured with high quality materials
Designed for underhood conditions
Quality constructed for durability
Application specific for this vehicle

from

$11.49

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$1.24

SEAL RING – COPPER

from

$38.99

Permatex’s The Right Stuff 1 Minute Series offers the fastest return to service in just 1 minute! This leak-proof, elastomeric “Formed-in-place” material is more reliable and longer lasting than pre-cut gaskets. It is blowout resistant and protects against leaks and seepage caused by vibration and thermal expansion. The Right Stuff 1 Minute Grey is specified for high torque and high vibration applications and is formulated to meet or exceed performance standards for long-term sealability, durability and handling.

Product Features:

Designed to perform under higher torque loads associated with engines having closely spaced bolt patterns
Sensor-safe, non-corrosive, RTV silicone
Protects against leaks caused by vibration and thermal expansion
Meets performance specs of OE silicone gaskets
Quickly returns vehicle to service in just 1 minute

from

$6.99

Permatex Ultra Grey is specified for high torque and high vibration applications. Ultra Grey offers a sensor-safe, low odor, non-corrosive formula and is OEM specified to fit dealership warranty requirements. This high performance gasket maker meets performance specs of OE silicone gaskets and can be used on high torque and vibration applications such as valve covers, water pump, intake manifold end seals ad thermostat housings.

Product Features:

High torque and rigidity
Sensor-safe, non-corrosive formula
OEM specified
Low-odor, non-corrosive formula
Ideal for closed spaced bolt patterns

from

$6.99

Permatex Water Pump & Thermostat RTV Silicone Gasket Maker is a noncorrosive, sensor-safe RTV silicone gasket material formulated for water pumps and thermostat housings. Permatex Water Pump & Thermostat has the highest water-glycol resistance available in an RTV silicone.

Product Features:

Sensor-safe, noncorrosive RTV silicone gasket material
Formulated specifically for water pumps and thermostat housings
Highest water-glycol resistance available in RTV silicone
Superior adhesion and flexibility
Can be used as a gasket maker or dressing

from

$137.57

Restore your vehicle’s cooling system to proper working order, and minimize the risk of premature failure, by installing a Bosch Auxiliary Water Pump. Bosch Auxiliary Water Pumps are designed to operate in the highly-stressful environment of today’s cooling systems. Eliminating the mechanical commutation system leaves the durability of the rotor bearings as practically the only limiting factor for service life. In addition to that, the lower number of moving parts results in significantly reduced noise.

Product Features:

OE Quality, reliability and service life
Leak-proof sealing of the drive
Fuel savings and reduced emissions
Cooling even without operation of the engine
CO²-reduction by optimized efficiency, speed control and reduced weight
Coverage of a wide hydraulic performance range
Reduced noise level

from

$154.43

Auxiliary Water Pump

from

$180.99

Carquest Premium auxiliary water pumps are 100% new, high-quality parts that meet or exceed original equipment (O.E.) specifications. All components, including the housing, impeller, controller, gaskets, and seals are designed for long-lasting service life. These electric water pumps are supplied with the gaskets or seals necessary for installation. Our Carquest Premium auxiliary water pumps undergo stringent testing to ensure superior performance that we stand behind with an industry-leading warranty.

Product Features:

Built to meet or exceed OE fit, form and function
All components necessary for installation are supplied with pump
100% tested for reliable performance
Follow all enclosed instructions to maximize pump life and validate warranty

from

$28.49

Specifically designed to perform under higher torque loads associated with engines having closely spaced bolt patterns (typically import vehicles). This product is blowout resistant, allowing leakproof gaskets to be made and put into service in just one minute. Sensor-safe, The Right Stuff GREY seals instantly, forming a reliable, long lasting elastomeric rubber gasket that outperforms pre-molded gaskets. Specified by major import OEMs, this material is resistant to powertrain fluids (oil, coolant and ATF) and operates in environments to 450°F (232°C) continuous; 500°F (260°C) intermittent.

Product Features:

Ideal for rigid cast aluminum parts
Meets OEM Specifications
Sensor safe & non-corrosive
Performs under higher torque loads associated with engines having closely spaced bolt patterns (typical of import vehicles)
Blowout resistant, allowing leakproof gaskets to be made in just one minute
Seals instantly, forming a reliable, long lasting elastomeric rubber gasket
Superior resistance to powertrain fluids including engine oil, transmission fluid, gear lube and coolants
Temperature range -60°C to 260°C (-75°F to 500°F) intermittent
Applications: Automotive, industrial and marine gaskets, valve covers, gearbox covers, pumps, compressors, oil pans, thermostat housings, water pumps, etc.

from

$1.79

Water Temperature Sensor O-Ring

from

$582.99

Manufactured with OEM quality materials and safety standards by an OE Supplier. This integrated thermostat housing will meet and exceed the expectations of the OE thermostat to insure the best product for your cooling system. Stands up to even the most demanding automotive cooling systems. Manufactured with OEM specifications and processes. Copper case and wax compound assures rapid response to temperature changes in the coolant as well as the design and function of the housing. Offset design, air relief valve, and OEM style seals included where applicable.

Product Features: